Pentair EVERPURE Twin, EVERPURE Triple, EVERPURE Quad, EVERPURE Quad Plus Installation And Operation Manual

EVERPURE

Figure 1 Twin Figure 2 Triple Figure 3 Quad Figure 4 Quad Plus

®

HIGH FLOW CSR FILTER SYSTEMS

SELECT A MOUNTING LOCATION

1. Give consideration to the weight of the unit when
operating (filled with water). Operating weights of
Everpure High Flow CSR Systems are:

• Twin System - 45 lbs (20.4 kg)

• Triple System - 47 lbs (21.3 kg)

• Quad System - 49 lbs (22.2 kg)

• Quad Plus System - 49 lbs (25.2 kg) + separate

surge/storage tank @ 60 lbs (27.2 kg)

INSTALLATION

1. Use the predrilled mounting holes in the manifold
bracket as guides. Mark and drill anchor holes. Mount
securely. See Figures 5-8.

2. Shut off power to equipment. If system is an Everpure
High Flow CSR Quad Plus (separate Everpure SR-X
Feeder and surge/storage tank), proceed to step 4.

3. Connect outlet ports of High Flow system to equipment
served per the instructions below. Always use NSF
approved pipe dope or plumber tape at all connections.
Use a backup wrench on all fittings while connecting to
avoid stress on the system components.

• The cross fitting before the SR-X Feeder has a

threaded outlet on top. Connect a minimum 1/2" I.D.
line from this outlet to fountain beverage equipment.

• The cross fitting has a flushing valve installed on the

bottom. Connect tubing to the flushing valve and run
to drain.

NOTE: Some municipal plumbing codes and good

sanitary practices require an air gap at the drain
termination point.

2. The location should allow for (See Figures 1-8):

• Minimum clearance of 2-1⁄2" (6.4 cm) under the
cartridge(s) so it can be lowered for removal
and replacement.

• Adequate space for “in” and “out” water line
connections. Be near a drain for flushing and near a
110V outlet if the optional Everguard™ Low Pressure
Alarm is used.

• Additional mounting and floor space for the separate
Everpure SR-X Feeder and surge/storage tank

(Quad Plus).

• Connect the outlet of the SR-X Feeder to the ice
machine make-up water (not condenser water) line
and coffee brewing equipment. Proceed to step 5.

4. For Everpure High Flow CSR Quad Plus System, connect
outlet to equipment served per the instructions below.
Always use a NSF approved pipe dope or plumber tape at
all connections. Use a backup wrench on all fittings while
connecting to avoid stress on the system components.

• Locate and mount the separate SR-X Feeder between

the High Flow CSR system and the ice machine.
Make-up water (not condenser water) line and coffee
brewing equipment.

• A tee fitting is located in the system header before

the surge tank isolation and flushing valve. Using
minimum 1/2" I.D. line, connect the outlet of this tee to
the fountain beverage and remote SR-X Feeder line.

IMPORTANT: Install a tee in this service water line to

separate the fountain water feed from the ice
machine/coffee brewer water feed.
In Massachusetts, a backflow preventer is
required for this installation.

FILTRATION & PROCESSING SOLUTIONS

HIGH FLOW CSR FILTER SYSTEMS INSTALLATION AND OPERATION GUIDE

1

30"

• Connect one branch of the service water tee to the
fountain beverage equipment. Connect the other
branch of the tee to the inlet of the SR-X Feeder.
Connect the outlet of the SR-X Feeder to the ice
machine make-up water (not condenser water) line
and coffee brewing equipment.

• The surge tank isolation and flushing valve is located
at the end of the system header. Using fittings and
hose provided, connect one branch of the valve to the
surge/storage tank. Connect a hose from the other
(flushing) branch and run to drain.

NOTE: Some municipal plumbing codes and good

sanitary practices require an air gap at the drain
termination point.

5. The surge/storage tank is pre-pressurized to 20 psi
(1.4 bar). Check pressure and adjust as necessary.

6. Install a manual shut-off valve leading to the system for
servicing and connect minimum 1/2" I.D. (3/4" for quad)
water line to the system inlet.

7. The optional EverguardTM Low Pressure Alarm (LPA)
consists of a pressure switch, audible/visual alarm box
and a power adapter. It is designed to detect a fixed
low pressure, approx. 20 psi (1.4 bar), condition as an
indication of loss of system outlet pressure either due
to an intentional shut-down or excess fouling of the
water filters, thus indicating the need for filter cartridge
change-out. If the system is equipped with the LPA,
follow these steps:

• Determine location of a convenient 110 VAC outlet to

plug in the LPA power adapter.

• Remove the protective rubber cap from the pressure

switch installed in the system header assembly. Insert
the wires from the LPA unit through the cap and
connect them to the terminals on the pressure switch.
Either wire can be connected to either terminal.
Replace the cap.

• Plug the LPA power adapter into an outlet. The audible

alarm should activate. Push the reset switch
to silence.

• Unplug the LPA unit.

8. Shut off the system inlet valve located on the inlet of the
prefilter head.

9. Check to be sure the o-ring on the prefilter housing
is sufficiently lubricated. Use a good grade of silicone
lubricant, if needed. Position the Everpure EC210
prefilter cartridge on guide seat in the bottom of the
bowl. Then thread the bowl into the head by hand. Use a
sump wrench to snug the bowl onto the head.

10. Install only genuine Everpure carbon filter cartridge(s)
into the filter head(s) following directions on the
cartridge label or as shown in the Cartridge Change
illustrations. Install the Everpure® SS-10 Scale Inhibitor
cartridge into the Everpure SR-X housing.

11. Turn on inlet water to the filter system and check
for leaks.

12. Open the flushing valve and flush the cartridge(s) by
running water through at full force for five (5) minutes.
This will set the filtering media and purge any air and
fines, insuring maximum filter life. See illustrations.

13. After flushing, close the flushing valve, turn on power
to equipment and plug the LPA (if so equipped) into the
electrical outlet. The system is ready for operation.

Check for compliance with state and local laws and regula­tions. Do not use with water that is microbiologically unsafe
or of unknown quality without adequate disinfection before or
after the system. Systems certified for cyst reduction may be
used on disinfected waters that may contain filterable cysts.

For installations in Massachusetts, the Commonwealth of
Massachusetts Plumbing Code 248 CMR shall be adhered to.
Consult your licensed plumber for installation of the system.
This system and its installation must comply with state and
local regulations.

DIMENSIONS

25.80"

FOUNTAIN

OUTLET

3/4" FNPT

INLET

3/4" FNPT

Figure 5 Twin

2 HIGH FLOW CSR FILTER SYSTEMS INSTALLATION AND OPERATION GUIDE

ICE MACHINE/
COFFEE
OUTLET
3/4" FNPT

25.59"

INLET

3/4" FNPT

Figure 6 Triple

FOUNTAIN

OUTLET
3/4" FNPT

ICE MACHINE/
COFFEE

OUTLET
3/4" FNPT

25.59"

INLET

31.38"

3/4" FNPT

34"

OUTLET
3/4" FNPT

ICE MACHINE/
COFFEE

OUTLET
3/4" FNPT

25.69"

INLET

3/4" FNPT

INSERT TEE FITTING.
ONE OUTLET TO
FOUNTAIN,
ONE OUTLET TO SRX.

OUTLET

3/4" FNPT

INLET

3/4" FNPT

ICE MACHINE/
COFFEE

OUTLET
3/4" FNPT

Figure 7 Quad

CARTRIDGE CHANGE DETERMINATION

• Replace the prefilter cartridge whenever it becomes
excessively dirty (observed visually or by flow restriction).
Follow the change instructions provided with the
cartridge.

• Replace carbon filter cartridges when capacity is
reached or when flow becomes inadequate, but at least
annually. All carbon filter cartridges on multiple cartridge
systems should be changed at the same time. Change
the Everpure SS-10 cartridge when product level in the
cartridge drops below 1/2" from the bottom of the bowl.

• The system pressure gauge or optional Everguard Low
Pressure Alarm (LPA) provides a quick, simple means
of determining when the filter cartridge(s) should be
checked. Installed on the system outlet manifold, the
gauge or LPA can be used to monitor both dynamic
(flowing) and static (line) pressure.

• The cartridge(s) should be changed when the pressure
gauge is in the red area while equipment is in operation,
and yet the needle shows adequate line pressure between
cycles.

• Observe the needle during the next equipment on cycle.
If the needle registers adequate pressure, it can be
assumed that the temporary low-pressure condition
was caused by a brief power failure or other incoming
pressure disruption.

• If the low pressure condition is not due to an external
condition, check/change the prefilter first. If the low
pressure condition is still not corrected, change the
carbon filter cartridges.

Figure 8 Quad Plus

FLUSHING

For maximum life, all carbon filter cartridges must be
flushed for five (5) minutes at full flow before use.

ALL NEW CARTRIDGES MUST BE FLUSHED AFTER EACH
CARTRIDGE CHANGE BEFORE BEING PUT INTO SERVICE!

If the cartridges are new, have been properly flushed and
both needle and follower register inadequate pressure, or the
LPA is sounding, you may be experiencing inadequate water
pressure or some restriction may exist in the inlet water
line. In either case, the incoming water pressure must be
improved to receive optimum filter life.

COMPLETE CARTRIDGE CHANGE INSTRUCTIONS CAN BE
FOUND ON THE FILTER CARTRIDGE LABEL.

Not for residential use. For food service applications only.

REPLACEMENT PARTS

Contact your local Pentair® Everpure® dealer for filter
cartridges or system replacement parts.

DESCRIPTION PART NUMBER

Inlet/Outlet Pressure Gauge EV3114-09

Inlet/Flushing Valve EV3114-07

O-ring for Prefilter or SR-X EV3112-40

Prefilter Bowl EV3112-38

SR-X Bowl EV3112-39

LPA Pressure Switch EV3016-41

Wrench EV3112-41

3 HIGH FLOW CSR FILTER SYSTEMS INSTALLATION AND OPERATION GUIDE

PRESSURE GAUGES

Low Inlet
Pressure

CARTRIDGE CHANGE PROCEDURE

E-Series Prefilter Cartridge Change

1. Shut off po wer to equip ment. Shu t off
inlet w ater ahea d of syste m.

Everp ure Carbo n Filter Car tridge
Change

1. Shut off po wer to equi pment. Shu t off

inlet w ater ahea d of syste m.

2. Push red rel ief valve . Unscrew b owl.
Remove prefilter cartridge.

2. Open flushi ng valve to r elieve pr essure.

3. Hold head fi rmly and push u pward. Tur n
cart ridge to le ft until i t stops.

Adequate Inlet

Pressure

3. Clean bow l with filt ered wate r only; NO
SPECIAL CLEANERS.

4. Feel he ad o-ring. I f dry, lubr icate wit h
high quality silicone lubricant.

4. Pull cart ridge down ward and ou t of head.

5. Hold head fi rmly. Align c artrid ge lug with
label . Insert n ew cartr idge firm ly
into he ad.

Low Outlet

Pressure

5. Install ne w prefilt er cartr idge in bowl .
Hand ti ghten bow l onto head .

6. Turn cartri dge right 90 ˚ until
rotation stops.

7. Repeat ste ps 3-6 for re maining
cartridges.

Adequate Outlet

Pressure

6. Turn on water. Turn o n power to
equipment.

Flushing

8. With flus hing valve f ully open, o pen inlet
wate r at full for ce for five m inutes. C lose
flushing valve.

9. Turn on pow er to equipm ent

SR-X Feeder Cartridge Change

1. Shut of f power to e quipment . Shut off
inlet w ater ahea d of syste m.

2. Press r ed press ure relief b utton on h ead.

3. Unscr ew bowl.

4 HIGH FLOW CSR FILTER SYSTEMS INSTALLATION AND OPERATION GUIDE

4. Remove o ld cartr idge.

5. Feel bo wl o-ring; i f dry, lubri cate wit h
silicone lubricant.

6. Insta ll new SS-10 car tridge in to head.

7. Hand tig hten bowl i nto head.

8. Turn on wat er.

9. Press r ed press ure relief b utton un til
wate r comes out o f valve por t.

10. Turn on po wer to equip ment.

OPERATING SPECIFICATIONS*

COMBINED MODEL NAME REPLACEMENT CARTRIDGE

FLOW RATE CAPACITY

GPM LPM GALLONS LITRES

High Flow CSR Twin - MC MC 3.3 12.5 18,000 68,000
High Flow CSR Twin - MC

2

MC

2

3.3 12.5 18,000 68,000
High Flow CSR Twin - XC XC 3.3 12.5 18,000 68,000
High Flow CSR Twin - XC

2

XC

2

3.3 12.5 18,000 68,000
High Flow CSR Twin - 4CB5 4CB5 3.3 12.5 12,000 45,400
High Flow CSR Twin - 7CB5 7CB5 5.0 18.9 20,000 75,700
High Flow CSR Triple - MC MC 5.0 18.9 27,000 102,000
High Flow CSR Triple - MC

2

MC

2

5.0 18.9 27,000 102,000
High Flow CSR Triple - XC XC 5.0 18.9 36,000 136,000
High Flow CSR Triple - XC

2

XC

2

5.0 18.9 36,000 136,000
High Flow CSR Triple - 4CB5 4CB5 5.0 18.9 18,000 68,000
High Flow CSR Triple - 7CB5 7CB5 7.5 28.5 30,000 113,550
High Flow CSR Quad - MC MC 6.6 25.2 36,000 136,000
High Flow CSR Quad - MC

2

MC

2

6.6 25.2 36,000 136,000
High Flow CSR Quad Plus - XC XC 6.6 25.2 48,000 181,600
High Flow CSR Quad Plus - XC

2

XC

2

6.6 25.2 48,000 181,600

* For individual cartridge specifications, refer to cartridge literature.

Temperature:

35 - 100°F (2 - 38°C)

Pressure:

10 - 125 psi (0.7 - 8.6 bar), non-shock

For cold water use only.

System Tested and Certified by NSF International against NSF/ANSI
Standard 42 and 53 for the reduction of:

Standard No. 42 —
Aesthetic Effects

Bacteriostatic Effects
(MC2 and XC2 only)
Chemical Reduction
Taste and Odor
Chlorine
Mechanical Filtration
Nominal Particulate Class I

Standard No. 53 —
Health Effects

Mechanical Filtration
Cyst (MC, MC2, XC, XC2 only)
Asbestos (MC, MC2 only)

The term ‘bacteriostatic’ indicates that the system limits the passage or growth of bacteria that may already exist in the incom­ing water. It does not mean that the water leaving the system is safer to drink than the water entering the system.

5 HIGH FLOW CSR FILTER SYSTEMS INSTALLATION AND OPERATION GUIDE

NOTES

6 HIGH FLOW CSR FILTER SYSTEMS INSTALLATION AND OPERATION GUIDE

NOTES

7 HIGH FLOW CSR FILTER SYSTEMS INSTALLATION AND OPERATION GUIDE

LIMITED WARRANTY

COMMERCIAL WATER TREATMENT EQUIPMENT

You have just purchased one of the finest water treatment units made. As an expression of confidence in this product, Pentair Filtration
Solutions, LLC (“PFS”) offers the following product warranty. This product is warranted against material defects in materials and
workmanship to the original end-user when installed in accordance with the PFS specifications. The warranty period commences on the
date of purchase and is administered as follows:

For a period of ONE YEAR Replaceable elements (i.e., filter & water treatment cartridges)*

For a period of FIVE YEARS The entire system (excluding replaceable elements)

The unit must be used in operating conditions that conform to PFS’s recommended guidelines. This warranty will not apply if the unit
has been modified, repaired or altered by someone not authorized by PFS.

If a part described above is found to have a material defect in materials or workmanship within the specified warranty period, you
should notify Pentair® Everpure technical service at the phone number listed below. Any part found materially defective within the terms
of this warranty will be repaired or replaced (at PFS’s discretion) by your local dealer or Pentair Everpure technical service. You pay only
freight from our factory and local dealer charges. Any item repaired or replaced pursuant to this warranty will be covered under the
original warranty terms of the system.

PFS is not responsible for damage caused by accident, fire, flood, freezing, Act of God, misuse, misapplication, neglect, oxidizing agents
(such as chlorine, ozone, chloramines and other related components), alteration, installation or operation contrary to our printed
instructions, or by the use of accessories or components which do not meet PFS’s specifications. Refer to the specifications section in
the Installation and Operating manual for approved application parameters.

Our product performance specifications are furnished with each water treatment unit. TO THE EXTENT PERMITTED BY LAW,
EVERPURE DISCLAIMS ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR PARTICULAR PURPOSE; TO THE EXTENT REQUIRED BY LAW, ANY SUCH IMPLIED WARRANTIES ARE LIMITED IN
DURATION TO THE PERIOD SPECIFIED ABOVE FOR THE ENTIRE WATER TREATMENT UNIT.

As a manufacturer, we do not know the characteristics of your water supply or the purpose for which you are purchasing this product.
The quality of water supplies may vary seasonally or over a period of time, and your water usage rate may vary as well. Water
characteristics can also differ considerably if this product is moved to a new location. For these reasons, we assume no liability for
the determination of the proper equipment necessary to meet your requirements, and we do not authorize others to assume such
obligations for us. Further, we assume no liability and extend no warranties, express or implied, for the use of this product with a non­potable water source or a water source which does not meet the conditions for use described in the owner’s guide or performance data
sheet for this product.

OUR OBLIGATIONS UNDER THIS WARRANTY ARE LIMITED TO THE REPAIR OR REPLACEMENT (AT PFS’S DISCRETION) OF THE
FAILED PARTS OF THE WATER TREATMENT UNIT, AND WE ASSUME NO LIABILITY WHATSOEVER FOR DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL, SPECIAL, GENERAL OR OTHER DAMAGES.

Some states do not allow the exclusion of implied warranties or limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. Similarly, some states do not allow the exclusion of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.

*Warranty applies to material defects in materials & workmanship only.

FILTRATION & PROCESSING SOLUTIONS

EVERPURESHURFLO WORLD HEADQUARTERS, 1040 MUIRFIELD DRIVE, HANOVER PARK, IL 60133 USA • WWW.EVERPURE.COM

800.942.1153 MAIN (US ONLY) • 800.942.1153 (US ONLY) • 630.307.3000 MAIN • 630.307.3030 FAX • [e-mail] EMAIL
PENTAIR AUSTALIA/NEW ZEALAND, 1-21 MONASH DRIVE, DANDENONG SOUTH, VIC 3175, AUSTRALIA

1300.576.190 TEL • [e-mail] EMAIL
EVERPURESHURFLO CHINA, 21F CLOUD 9 PLAZA, NO 1118, SHANGHAI, 200052, CHINA

86.21.3211.4588 TEL • 86.21.3211.4580 FAX • [e-mail] EMAIL
EVERPURESHURFLO INDIA, GREEN BOULEVARD, B-9/A, 7TH FLOOR - TOWER B SECTOR 62, NOIDA - 201301

91.120.419.9444 TEL • 91.120.419.9400 FAX • [e-mail] EMAIL
EVERPURESHURFLO EUROPE, PENTAIR WATER BELGIUM BVBA, INDUSTRIEPARK WOLFSTEE, TOEKOMSTLAAN, 30 B-2200 HERENTALS, BELGIUM

+32.(0).14.283.500 TEL • +32.(0).14.283.505 FAX • [e-mail] EMAIL
EVERPURESHURFLO JAPAN INC., HASHIMOTO MN BLDG. 7F, 3-25-1 HASHIMOTO, MIDORI-KU, SAGAMIHARA-SHI KANAGAWA 252-0143, JAPAN

81.(0)42.775.3011 TEL • 81.(0)42.775.3015 FAX • [e-mail] EMAIL
EVERPURESHURFLO SOUTHEAST ASIA, 390 HAVELOCK ROAD, #04-01, KING’S CENTRE, SINGAPORE 169662

65.6795.2213 TEL • FAX: [phone] FAX • [e-mail] EMAIL

All Pentair trademarks and logos are owned by Pentair, Inc. or its affiliates. All other registered and unregistered trademarks and logos are the property of their
respective owners. Because we are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice.
Pentair is an equal opportunity employer.

© 2014 Pentair Filtration Solutions, LLC. All Rights Reserved.

EPA Est. No. 002623-IL-002

EV3112-78 Rev F MY14