WWW.PENNBARRY.COM
©PENNBARRY 2008
14
PENNBARRY
Hi-Ex Roof Ventilators
TM
Roof Ventilators
H
i
E
x
Engineering Specifications
Engineering Specifications
›
Model
HC = Standard Height;
Cast Aluminum Propeller
HF = Standard Height;
Cast Aluminum Propeller;
AMCA Certied
HX = Standard Height;
Fabricated Steel Propeller
HS = HiteSaver; Cast Aluminum Propeller
HZ = HiteSaver; Fabricated Steel Propeller
›
Unit Size
24 36 48 60
30 42 54 72
›
Drive Type
D = Direct Drive
B = Belt Drive
›
Motor Tap
M = 690 RPM
Q = 1750 RPM
Q1 = 1750 RPM
Q2 = 1750 RPM
T = 1140 RPM
T1 = 1140 RPM
T2 = 1140 RPM
T3 = 1140 RPM
W = 860 RPM
W1 = 860 RPM
W2 = 860 RPM
W3 = 860 RPM
›
Motor Speed
1 = Single Speed
2 = 2S2W 1800/1200
3 = 2S1W 1800/900
›
Horse Power
1/4 3/4 2 7 1/2
1/3 1 3 10
1/2 1 1/2 5 15
0 = None
X = Special
›
Enclosure
O = Open Drip Proof
T = Totally Enclosed
E = Explosion Proof
X = Special
›
Voltage
B = 115V E = 208V P = 460V
D = 200V G = 230V R = 575V
X = Special
›
Phase
1 = Single
3 = Three
›
Cycle
5 = 50 Hz
6 = 60 Hz
›
Efciency
S = Standard
P = Premium
›
Paint / Coating
0 = None
B = Epoxy*
C = Heresite*
D = Heresite with UV*
Q = Enamel*
X = Special
* Not available with choice of color.
›
Color
0 = None
00 = Standard Gray
50 = Chrome Green
53 = Williamsburg Blue
55 = Pale Green
56 = Dove Gray
61 = White
63 = Oxford Beige
65 = Dover White
66 = Desert Tan
70 = Black
73 = Smoke Gray
77 = Brick Red
79 = Peppercorn
81 = Pale Brown
83 = Chocolate Brown
85 = Timeless Bronze
94 = Charcoal
X = Special
›
AMCA Spark Rating
0 = None
C = Standard
B = Optional
›
Damper
0 = None
BDD = Gravity Backdraft Damper
MD1 = Gravity Backdraft Damper 115V
MD2 = Gravity Backdraft Damper 230V
MD4 = Gravity Backdraft Damper 460V
ED1 = Explosion Proof Motor
Operated Damper 115V
›
Screen
0 = None
B = Bird Screen
S = Insect/Bird Screen
›
Roof Curb
0 = None J = SCA16 T = UA12
A = UCG8 K = UCA18 U = UA18
B = UCG12 L = UG12 V = UG18
C = UCG18 M = SA16 W = URA12
D = UCA8 N = SFG12 Y = URA18
E = UCA12 P = SFG18 1 = URG12
F = SFA12 Q = SG16 2 = URG18
G = SFA18 R = SRA16
H = SCG16 S = SRG16
›
Slope
0 = None
S = Single
D = Double
›
Metal Liner
0 = None
L = Metal Liner
›
Damper Holding Plate
0 = None
P = Damper Holding Plate
›
Neoprene Gasket
0 = None
G = Gasket
›
No Wooden Nailer
0 = None
N = No Wooden Nailer
›
Curb Paint/Coating
0 = None
B = Air Dried Epoxy
Q = Air Dried Enamel
X = Special
›
Thermal Overload Protection
0 = None
P = Thermal Protection
›
Disconnect Switch
0 = None
3R = Nema 3R Disconnect Switch
4 = Nema 4 Disconnect Switch
7 = Nema 7 Disconnect Switch
9 = Nema 9 Disconnect Switch
X = Special
›
Internal Wiring
0 = None
3R = Nema 3R Internal Wiring
4 = Nema 4 Internal Wiring
X = Special
›
Firestat Switch
0 = None
F = Firestat Switch
›
Extended Lube Lines
0 = None
E = Lube Lines
›
Aluminum Housing
0 = None
H = Aluminum
›
Roof Pitch Adapters
0 = None
S = Single Slope
D = Double Slope
WWW.PENNBARRY.COM
©PENNBARRY 2008
PENNBARRY
15
TM
Roof Ventilators
H
i
E
x
Engineering Specifications
Hi-Ex Roof Ventilators
Engineering Specifications
›
Remote Drive with Cover
0 = None
C = Remote
›
Belt / Bearing Cover
0 = None
B = Cover
›
Mag Damper Latch
0 = None
L = Latch
›
Inlet Guard
0 = None
G = Guard
›
Heat / Smoke Kit
0 = None
H = Heat / Smoke
›
Helper Spring
0 = None
H = Helper Spring
›
Torsion Spring
0 = None
T = Torsion Spring
› HC
Direct Drive Units
Direct Drive Axial Upblast Roof exhaust
fan shall be Hi-Ex HC, manufactured by
PennBarry; Richardson, TX 75081.
Units shall be weather resistant and
designed to withstand prevailing wind
velocities. A heavy gauge galvanized
motor mounting panel shall be securely
fastened to heavy gauge galvanized airshaft. Airshaft shall be welded to a heavy
gauge galvanized base with welded corners, pre-punched mounting holes, and a
deeply spun venturi. A ribbed reinforced
galvanized windband shall be securely
fastened to air shaft and shall include
automatic buttery dampers which open
and close with the start and stop of the
fan. No portion of fan shall protrude below the roof line.
Statically and dynamically balanced propellers shall be cast aluminum and airfoil
shaped. Motors shall be continuous duty,
ball bearing design, positively cooled,
and furnished at the specied voltage
and phase.
› HX
Direct Drive Units
Direct Drive Axial Upblast Roof exhaust
fan shall be Hi-Ex HX, manufactured by
PennBarry; Richardson, TX 75081.
Units shall be weather resistant and
designed to withstand prevailing wind
velocities. A heavy gauge galvanized
motor mounting panel shall be securely
fastened to heavy gauge galvanized airshaft. Airshaft shall be welded to a heavy
gauge galvanized base with welded corners, pre-punched mounting holes, and a
deeply spun venturi. A ribbed reinforced
galvanized windband shall be securely
fastened to air shaft and shall include
automatic buttery dampers which open
and close with the start and stop of the
fan. No portion of fan shall protrude below the roof line.
Statically and dynamically balanced propellers shall be cast aluminum and airfoil
shaped. Motors shall be continuous duty,
ball bearing design, positively cooled,
and furnished at the specied voltage
and phase.
Belt Drive Units
Belt Drive Axial Upblast Roof exhaust
fan shall be Hi-Ex HC, manufactured by
PennBarry; Richardson, TX 75081.
Units shall be weather resistant and
designed to withstand prevailing wind
velocities. A heavy gauge galvanized
motor mounting panel shall be securely
fastened to heavy gauge galvanized airshaft. Airshaft shall be welded to a heavy
gauge galvanized base with welded corners, pre-punched mounting holes, and a
deeply spun venturi. A ribbed reinforced
galvanized windband shall be securely
fastened to air shaft and shall include
automatic buttery dampers which open
and close with the start and stop of the
fan. No portion of fan shall protrude below the roof line.
Statically and dynamically balanced propellers shall be cast aluminum and airfoil
shaped. Motors shall be continuous duty,
ball bearing design, positively cooled,
and furnished at the specied voltage,
phase, and enclosure. Shafts shall be
turned, ground, polished, and rust protected. Pulleys shall be adjustable, cast
iron, machined, keyed, securely attached, and sized for 150% of the horsepower at its rated maximum speed.
Belt Drive Units
Belt Drive Axial Upblast Roof exhaust
fan shall be Hi-Ex HX, manufactured by
PennBarry; Richardson, TX 75081.
Units shall be weather resistant and
designed to withstand prevailing wind
velocities. A heavy gauge galvanized
motor mounting panel shall be securely
fastened to heavy gauge galvanized airshaft. Airshaft shall be welded to a heavy
gauge galvanized base with welded corners, pre-punched mounting holes, and a
deeply spun venturi. A ribbed reinforced
galvanized windband shall be securely
fastened to air shaft and shall include
automatic buttery dampers which open
and close with the start and stop of the
fan. No portion of fan shall protrude below the roof line.
Statically and dynamically balanced propellers shall be cast aluminum and airfoil
shaped. Motors shall be continuous duty,
ball bearing design, positively cooled,
and furnished at the specied voltage,
phase, and enclosure. Shafts shall be
turned, ground, polished, and rust protected. Pulleys shall be adjustable, cast
iron, machined, keyed, securely attached, and sized for 150% of the horsepower at its rated maximum speed.
WWW.PENNBARRY.COM
©PENNBARRY 2008
16
PENNBARRY
Hi-Ex Roof Ventilators
TM
Roof Ventilators
H
i
E
x
Engineering Specifications
Engineering Specifications
› HZ
Direct Drive Units
Direct Drive Axial Low Contour Upblast Roof exhaust fan shall
be Hi-Ex HZ, manufactured by PennBarry; Richardson, TX
75081.
Units shall be weather resistant and designed to withstand pre-
vailing wind velocities. A heavy gauge galvanized motor mounting panel shall be securely fastened to a ribbed reinforced
galvanized windband. Windband shall be securely attached
to a heavy gauge galvanized base with welded corners, prepunched mounting holes, and a deeply spun venturi, and shall
include automatic buttery dampers which open and close with
the start and stop of the fan.
Statically and dynamically balanced propellers shall be cast alu-
minum and airfoil shaped. Motors shall be continuous duty, ball
bearing design, positively cooled, and furnished at the specied
voltage, phase, and enclosure.
Belt Drive Units
Belt Drive Axial Low Contour Upblast Roof exhaust fan shall be
Hi-Ex HZ, manufactured by PennBarry; Richardson, TX 75081.
Units shall be weather resistant and designed to withstand prevailing wind velocities. A heavy gauge galvanized motor mounting panel shall be welded and securely fastened to a ribbed
reinforced galvanized windband. Windband shall be securely
attached to a heavy gauge galvanized base with welded corners, pre-punched mounting holes, and a deeply spun venturi,
and shall include automatic buttery dampers which open and
close with the start and stop of the fan.
Statically and dynamically balanced propellers shall be cast alu-
minum and airfoil shaped. Motors shall be continuous duty, ball
bearing design, positively cooled, and furnished at the specied
voltage, phase, and enclosure. Shafts shall be turned, ground,
polished, and rust protected. Pulleys shall be adjustable, cast
iron, machined, keyed, and securely attached, and sized for the
150% of the horsepower at its rated maximum speed.
› HF
Belt Drive Units
Belt Drive Axial Upblast Roof exhaust fan shall be Hi-Ex HF,
manufactured by PennBarry; Richardson, TX 75081.
Units shall carry UL705 listing and be CSA certied. Units shall
be weather resistant and designed to withstand prevailing wind
velocities. A heavy gauge galvanized motor mounting panel
shall be securely fastened to heavy gauge galvanized airshaft.
Airshaft shall be welded to a heavy gauge galvanized base with
welded corners, pre-punched mounting holes, and a deeply
spun venturi. A ribbed reinforced galvanized windband shall be
securely fastened to air shaft and shall include automatic butter-
y dampers which open and close with the start and stop of the
fan. No portion of fan shall protrude below the roof line.
Statically and dynamically balanced propellers shall be of fab-
ricated steel. Motors shall be continuous duty, ball bearing de-
sign, positively cooled, and furnished at the specied voltage,
phase, and enclosure. Shafts shall be turned, ground, polished,
and rust protected. Pulleys shall be adjustable, cast iron, machined, keyed, securely attached, and sized for 150% of the
horsepower at its rated maximum speed.
› HS
Belt Drive Units
Belt Drive Axial Low Contour Upblast Roof exhaust fan shall
be Hi-Ex HS, manufactured by PennBarry; Richardson, TX
75081.
Units shall be weather resistant and designed to withstand pre-
vailing wind velocities. A heavy gauge galvanized motor mounting panel shall be welded and securely fastened to ribbed
reinforced galvanized windband. Windband shall be securely
attached to a heavy gauge galvanized base with welded corners, pre-punched mounting holes, and a deeply spun venturi,
and shall include automatic buttery dampers which open and
close with the start and stop of the fan.
Statically and dynamically balanced propellers shall be heavy
gauge steel. Motors shall be continuous duty, ball bearing de-
sign, positively cooled, and furnished at the specied voltage,
phase, and enclosure. Shafts shall be turned, ground, polished,
and rust protected. Pulleys shall be adjustable, cast iron, machined, keyed, securely attached, and sized for 150% of the
horsepower at its rated maximum speed.
Each model HS fan shall bear the AMCA Licensed Ratings Seal
for Air and Sound Performance (30-48), and shall be UL (UL
Std. 705, UL Std. 793 optional).
If specied, Heat and Smoke option, fan shall additionally provide UL 793 Listing (500ºF for 4 hrs./1000ºF for 15 min.), pedestal mounting, remote motor mounting, and damper springs
activated by fusible links.
Loading...