PennBarry Fumex Product Manual

FUMEX

PRODUCT GUIDE

Upblast Roof Exhausters

PennBarry | Your Single Source for Commercial & Industrial Supply & Exhaust Fans | www.pennbarry.com

TABLE OF CONTENTS

INTRODUCTION 3

CERTIFICATIONS & LISTINGS 4

FEATURES & BENEFITS 5-6

OPTIONS & ACCESSORIES 7-12

MOTOR AVAILABILITY 13-14

DIRECT DRIVE | DIMENSIONS 15

BELT DRIVE | DIMENSIONS 16

FAN SELECTIONS 17-18

www.PennBarry.com 2

INTRODUCTION

Fumex Series of Centrifugal Fans

Fumex centrifugal fans are designed for medium to high pressure applications and are available in a range of capacities. They can be

either roof or wall mounted. While suitable for general ventilation, Fumex fans are specically designed to discharge contaminated or
grease-laden air or fumes up and away from building surfaces. The optional “Fatrap” (UL762) restaurant grease exhaust conguration
(see Fatrap Conguration) makes Fumex fans particularly suited for all food service applications and chemical fume hoods. The optional
heat and smoke removal conguration (see Smoke Removal) makes Fumex fans especially prepared for heat and smoke control systems.
The optional high wind construction makes Fumex fans well-tted for high wind hurricane zones.

Fumex fans feature a weather-resistant, seamless spun aluminum housing which provides ample drainage and works in conjunction
with a patented wheel design and deeply spun inlets to provide smooth quiet airow through the ventilator. The centrifugal wheels are
aluminum, non-overloading, backward inclined, robotically welded, and dynamically balanced.

Direct Drive Units

Model: FX (V/S/R/Q/Q1/Q2)

• Static pressure up to 1.5” wg.

• Flow capacity up to 4,489 CFM.

• Fatrap (FT) option available on sizes 13, 16, and 18.

• High Wind Construction (-HW) option available.

High Pressure Belt Drive Units

Model: FX (BH)

• Static pressure up to 3.0” wg.

• Flow capacity up to 8,623 CFM.

• Fatrap (FT) option available.

• Heat & Smoke Removal (-HS) option available.

• High Wind Construction (-HW) option available.

www.PennBarry.com 3

Centrex Direct Drive

Standard Duty Belt Drive Units

Model: FX (B)

• Static pressure up to 2.5” wg.

• Flow capacity up to 21,511 CFM.

• Fatrap (FT) option available.

• Heat & Smoke Removal (-HS) option available.

• High Wind Construction (-HW) option available.

CERTIFICATIONS & LISTINGS

AMCA Certications

PennBarry certies that the Fumex direct drive and belt drive models FX, FXBH, and FXBHFT shown herein are licensed

to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA

Publication 211 and Publication 311 and comply with the requirements of the AMCA Certied Ratings Program. FX27B
is not AMCA Certied.

cULus Certication

Fumex fans carry the UL label, UL705 (ZACT/ ZACT7), le #E28413. Fumex fans with the “Fatrap” option carry the UL
label, UL762 (YZHW/ YZHW7), le #MH10684. Fumex fans with the heat and smoke removal option carry the UL label,
UL793 (ZAXH/ZAXH7), le #MH19473

High Velocity Hurricane Zone (HVHZ)

Miami-Dade NOA # 17-0112.06
Florida Product Approval #21559

www.PennBarry.com 4

FEATURES & BENEFITS

Motor Selection

Both direct drive and belt drive models are available with a wide range of voltages and enclosures (see Motor Selection for a complete
listing). Standard belt drive Open Drip Proof (ODP) ball bearing motors are selected using a conservative portion of the NEMA service
factor. Standard direct drive ODP motors have Class B insulation and internal overload protection. Overload protection is available as an

option on belt drive models. Each size is carefully engineered to match the motor to the wheel capacity.

Sound Performance

Fumex units deliver outstanding air performance with minimal noise and have the lowest AMCA licensed sound performance in the
industry.

Curb Caps (Base)

Curb caps for direct drive and standard duty belt drive models are available in galvanized steel (standard) or aluminum (optional). Curb

caps for high capacity belt drive models are available only in aluminum. All curb caps have fully welded corners and are pre-punched to

ensure a leak-tight and easy installation.

Forced Motor Cooling

Motors and drive components are located out of the airstream in a separate compartment. A cooling tube between the motor dome and
discharge apron enables fresh air to be drawn into the motor housing during fan operation. This positive cooling promotes longer life
for motor and drive components.

Easy Maintenance Access

By removing the fasteners, the motor dome lifts o for complete access to all the drive components.

Vibration Isolators

Multidirectional, rubber-in-shear vibration isolators mitigate residual vibration transmission from the unit to the building.

Structural Integrity

Durable housings of spun aluminum have a high strength-to-weight ratio and incorporate a rolled bead for additional strength. There

are no welds to break or seams to leak. The heavy-gauge motor mounting platform provides positive rigidity between all components

of the power train assembly.

Internal Bracing

Tri-Strut™ supports transfer the weight of the motor mounting platform directly to the curb mounting surface. The aluminum spun
housing, therefore, is not used to support any weight. For grease laden applications, there is less surface for grease build-up during
normal operation.

Solid Steel Shafts

Sized so the rst critical speed is a minimum of 130% of maximum cataloged operating speed, shafts are precision ground and polished.

Self-Aligning Bearings

Heavy-duty bearings are sized for a minimum L50 life in excess of 200,000 hours of operation. One hundred percent factory tested, they

are designed for air handling applications.

Drives and Belts

Pulleys are pre-set to the specied RPM. Cast iron variable pitch pulleys are adjustable, allowing for eld balancing based on actual eld
conditions. All pulleys are sized for at least 150% of the driven horsepower.

Conduit

Both direct and belt drive units include a large 1” nominal conduit chase (not available on heat and smoke removal units; wiring is run via

the cooling tubes) for easy installation of wiring from the motor dome to below the curb cap. Fatrap units are factory wired to an external

NEMA 3R junction box.

www.PennBarry.com 5

FEATURES & BENEFITS

Reverse Venturi

Reverse venturi reduces turbulence and improves distribution of the air as it enters the wheel
inlet and is “captured” by the blades.

Wheels

Fumex fans oer patented wheel designs. Carefully matched, highly-tooled venturis enhance the performance of these backward inclined

and non-overloading centrifugal wheels. Made of advanced aluminum alloys, the various wheel components provide superior strength

and durability, as well as spark resistant construction. The heat and smoke removal conguration utilizes steel construction.

Silent Wheel (Direct Drive)

• Blades’ highly curved leading edges provide unsurpassed low sound numbers with excellent

air performance.

• Backplate and inlet are stamped for consistency, plus dynamic balancing ensure smooth,

vibration-free operation.

• Riveted or riveted and welded construction ensure superior dependability over other wheel
designs.

Standard Duty, All Welded Wheel

(Standard Duty & High Pressure Belt Drive)

• Blades are curved for improved air performance while increasing their strength and rigidity.

• Backplate and inlet are stamped for consistency. They include a perimeter rim which enhances strength and improves balancing.

• Wheel assembly is robotically welded to provide extremely durable and consistent performance.

• Wheel is dynamically balanced. Balancing weights are mechanically attached to the inside of the rims of both the backplate and

wheel inlet. This allows a precise placement of the weights anywhere within a full 360º range on two separate planes, without the
possibility of detachment.

Enhanced Direct Drives

These enhanced units have Gplus™ motor selection up to 2 HP (available on single phase and three phase) and are available up to size

24. Design enhancements to Direct Drive Fumex models signicantly improve air performance, while Gplus™ EC motors oer higher

eciency, and quieter, more reliable operation. Combined with PennBarry’s patented, backward inclined, centrifugal wheel, these fan
units deliver low noise and high eciency performance.

Internal Wiring

All direct and belt drive models with ODP motors feature a polarized disconnect plug which is factory wired from the motor to the
junction box. This provides a positive method of electric shut-o as required by most codes without requiring the traditional disconnect

switch. In addition, weather resistant NEMA 3R wiring is available for selection.

www.PennBarry.com 6

OPTIONS & ACCESSORIES

Spare Belt

One or two extra sets of spare belts are available for selection.

iQ Controllers

There are two types of iQ controllers available:

• iQ-IPCM (Intelligent Pressure Control Module), with Duct Sentry™ technology is designed to maintain constant pressure 24/7 within

a duct system by controlling fan motor speed

• iQ-MS (Multi-Speed Controller), with dual set-point interface allows the user to set and remotely switch among two dierent motor

speeds.

Both of them provide motor control signal output of 0-10 VDC for seamless integration with today’s advanced motor technologies to

provide substantial energy savings and peace of mind.

Extend Lube Lines

Preloaded at the factory, lube lines allow bearing maintenance when easy access to the bearings is unavailable.

Stainless Steel Hardware

If another material is desired for the unit’s hardware, stainless steel hardware is available for selection.

Variable Frequency Drives

Variable frequency drives (VFDs) are designed to meet performance requirements while increasing eciency. By varying the fan

motor input frequency and voltage, the VFD controls the motor speed and torque, helping to improve productivity and lower energy

consumption. The VSC and VSA are ideal for both new and retrot fan applications. Shipped loose and separately.

0-10 Output Potentiometer

Potentiometers are always paired with Green Plus motors. With the potentiometer, the Green Plus motors can be turned down to as low

as 80% the max operating speed while maintaining 90% eciency through the operating range. Additionally, the Green Plus can accept

0-10V input to tie to building management systems, not only allowing for savings in direct fan energy consumption but reducing the

exhaust of conditioned air during o peak hours as well

Stainless Steel Shaft

If another material is desired for the motor shaft, stainless steel shafts are available for selection.

Transformers

To meet local requirements 277V transformers are available for all direct drive units. The transformers are step-down and will step the

voltage down to 120V. Shipped loose for eld installation.

Finishes

Coatings such as Polyester Powder Coat, Epoxy Powder Coat, Phenolic Epoxy Powder Coat, and others are available. See the coatings
brochure for details.

www.PennBarry.com 7

OPTIONS & ACCESSORIES

Mounting Pedestal

The 12” high mounting pedestal, available in aluminum or galvanized steel, incorporates a removable access panel for easy inspection
and service of motor operated backdraft dampers. It provides solid ventilator support and a weather resistant seal that does not injure or
disturb ashing. This item should not be used with Fatrap units.

Hinged Sub-Base

Hinged sub-bases provide access to the curb well for damper service or the clean out for grease applications. Constructed with a rust
proof hinge arrangement and low height, (3 ½”) the assembly is easily manipulated and reduces the impact on overall installation height.
This accessory is available for use with most models for either factory built or existing roof curbs.

Fumex
Base

Floating Hinge Kit

A oating hinge kit is also available for eld installation. This assembly connects

the exhauster directly to the roof curb and provides the same level of access as
the hinged sub-base.

Floating Hinge Plate

Back Plate

(Inside Curb/Pedestal)

Ventilator
Curb/Pedestal

Bushing

Aluminum Bird & Insect Screen

Bird screens are available for all direct and belt drive models. An aluminum insect screen with a smaller mesh than the standard bird
screen is also available. However, please note that NFPA 96 installations do not allow the use of bird or insect screens. The requirements

of local codes must be reviewed to determine if there are any conicts.

Internal Wiring

NEMA 3R wiring is available for both direct and belt drive models.

Backdraft Dampers

Backdraft dampers are available for either gravity or motorized operation (motor kit optional). Dampers feature square galvanized steel
frames and multi-leaf, roll formed aluminum blades with nylon bearings. Backdraft dampers should not be used when venting kitchen

hoods. NFPA 96 installations do not allow the use of dampers. The requirements of local codes must be reviewed to determine if there

are any conicts.

Safety Service Switch

Safety service switches are available to allow positive electrical shut-o and

safety. Switches are factory mounted when factory wiring is requested. Wiring

is only run from the motor to the junction box. (Factory wiring of explosion

proof applications is not available.) A wide range of NEMA rated enclosures
with service switches are available for indoor, outdoor, and explosion proof

installations. Service switches are to be eld wired by a licensed electrician.

Firestat Switch

Firestat switch automatically disconnects the unit when the temperature of the
air being exhausted exceeds a preset rating.

www.PennBarry.com 8

OPTIONS & ACCESSORIES

Time-Delay Switch

(For select direct drive models only) The Airminder Model AM12 switch is a

UL recognized and CSA certied time-delay relay that operates both the fan

and room light to ventilate an area even after the occupants depart. In the

“On” position, the Airminder turns the light and fan on immediately. In the “O”
position, the light goes o immediately, and the fan is in operation for a period

of time as preset from 1 to 60 minutes. Suitable only for 1/3 HP maximum at
120/1/60.

Speed Controllers

The Lek-TrolTM controller allows adjustment in speed to a maximum of 50%
reduction, which results in a very cost eective means for system balancing. The
device can be located under the fan dome to prevent unauthorized tampering

or on the wall for ease of operation by the building occupants. (Available on
direct drive units with ODP motors and some select TE motors. See reference
table under Motor Availability)

Automatic Belt Tensioner

The factory mounted Automatic Belt Tensioner accessory eliminates the need for re-tensioning the belt after start-up. It is constructed

from 10 gage galvanized steel and incorporates ve torsion springs to automatically position the motor and maintain proper belt tension.
Additional benets include reduced belt and pulley wear and simplied belt replacement without tools. The Automatic Belt Tensioner is
available for Fumex models FX08B, FX10B, FX12BH, FX13B,

FX13BHFT and FX14B with 1/4, 1/2, 3/4, and 1 HP ODP motors. It can also be used with 1.5 HP, 3-phase ODP motors.

Spark Resistant Construction

AMCA ‘B’ construction is available as standard construction on direct drive units and as an option on belt drive units (not available on heat
and smoke removal units). If required, an explosion proof motor and service switch may be selected as options.

Wall Mounting

This option is provided as a separate product line, whose models include a “W” prex. Product line includes models up to size 24, motors
up to 2HP, and round bases (not available on heat and smoke removal units).

Prefabricated Curb

A variety of sizes of prefabricated roof curbs are available. Galvanized steel unibeam curbs are the most popular. For a complete listing
of all curb types and sizes available, see the latest PennBarry Ventilation Curb brochure. Please note that NFPA 96 installations require a
specic curb height. See Fatrap conguration on the next page.

www.PennBarry.com 9

OPTIONS & ACCESSORIES

Fumex Curb

w/Cant

T (s q.)

Vented S elf

Fl ashing

18 " MIN.

1 1 /2"

H

Standa rd

R o (sq.)

A (sq.)

Model E

FX08S/R 18.5 17 25 9 8.75 18

FX10S/R 18.5 17 25 11.5 11.25 18

FX11V/S/R/Q 18.5 17 25 11.5 11.25 18

FX13V/S/R/Q 18.5 17 25 11.5 11.25 18

FX16V/S/R/Q1/Q2 20.5 19 27 16 15.75 18

FX18V 28.5 27 35 20 19.75 18

FX08B to FX14B 24.75 23.25 31.25 16 15.75 18

FX12BH 24.75 23.25 31.25 16 15.75 18

FX13BHFT 24.75 23.25 31.25 16 15.75 18

FX16B and FX18B 28.5 27 35 20 19.75 18

FX18BH 28.5 27 35 20 19.75 18

FX24B 33.5 32 40 25 24.75 18

FX24BH 33.5 32 40 25 24.75 18

FX27B and FX30B 36.5 35 43 28 27.75 18

FX36B 44.5 43 51 36 35.5 18

(4)

SQ T

(2)

SQ A SQ Ro(3) SQ Damper Size SQ Galv. Steel Gauge

Standard heights “H” are 8”, 12”, and 18” including wood nailer. ”T” dimension of curb is 1 1/2” less than the dimension of inside base of fan (“E”). “Ro”
refers to Roof Opening. “E” dimension is inside base of fan. For FT (Fatrap) units, curbs are cantless, 18” high and optionally vented.

Exploded View

SAFETY
DISCONNECT
SWITCH

ALUMINUM
BIRD AND INSECT
SCREEN

HINGED
SUB-BASE

PREFABRICATED
CURB

BACKDRAFT
DAMPER

www.PennBarry.com 10

OPTIONS & ACCESSORIES

Fatrap Conguration

Fatrap congured fans are ideal for use in commercial kitchens over grilles, charcoal broilers, deep fat fryers, steam tables, ranges,
dishwashers, and other appliances. Fumex fans are specially congured for food service applications with the addition of a group of

accessories that either meets a requirement or eases installation requirements according to NFPA 96. NFPA 96 “Standard for Ventilation

Control and Fire Protection of Commercial Cooking Operations” is the generally recognized authority nationwide for restaurant installation

requirements. However, local codes may vary.

Included in the units are the following.

• UL 762 Listing: Fatrap congured Fumex fans are listed at 400°F — 100°F higher than UL requirements. The high temperature rating

is the result of the fan’s highly ecient forced motor cooling capability. Three direct drive (sizes 13 – 18) and all belt drive models are

listed.

• Pre-wired Junction Box: A weather-proof junction box is factory wired and mounted to the housing exterior. An appropriately sized

service switch is commonly selected as an additional option. These items meet the code requirements for positive electric shut-o.

• Grease Collector/Separator Box: Designed for easy installation, the grease is routed from a single swiveling collection spout to an

amply sized durable galvanized steel box, trapping grease and residue and avoiding discharge onto the roof surface. Additionally,

these boxes separate the water from the grease, prolonging the time required between periodic maintenance.

Additional Fatrap Accessories

Ventilated Curbs and Pedestals: For buildings two stories or higher NFPA 96 requires the use of ventilated mounting curbs or pedestals to

provide an approved arrangement for connecting a range hood and duct work to the roof fan. PennBarry’s ventilated mounting curbs and
pedestals, 18” high, comply with that standard when properly installed. Ventilated curbs have a at mounting ange for fastening directly
to the roof deck. This ange should be securely fastened and ashed to ensure weather tightness. Ventilated pedestals are designed to
t on an existing curb. They provide cap ashing when so installed.

ADDITIONAL
COOLING TUBE

STEEL WHEEL

PREFABRICATED
CURB

www.PennBarry.com 11

OPTIONS & ACCESSORIES

Heat & Smoke Removal Conguration

While Fumex fans are commonly used for general ventilation, they are also designed to discharge contaminated or grease-laden air

or fumes up and away from building surfaces with the Fatrap option. When equipped with the Heat and Smoke Removal option, this
series of fans incorporates features exclusively designed to exhaust heat and smoke in the event of re. During these emergencies, the

fans are designed to operate at the temperature and time limits stated below. To maintain power to these fans during emergencies,

special consideration must be made for eld power supply. In the event of an emergency, if power is maintained, the units will operate

for the times and temperatures indicated, after which they will continue to operate until they are destroyed by the extreme temperature

generated during an actual re, or their roof structure collapses.

For smoke control systems, Heat and Smoke Removal congured fans are listed per UL for emergency smoke removal, referencing UL705,
UL793, Industrial Risk Insurers (IRI), and Southern Building Code Congress International (SBCCI).

The UL standard requires the fan to run at 500°F for 4 hours (IRI) and 1000°F for 15 minutes (SBCCI). PennBarry Heat and Smoke Removal
congured Fumex units are listed at 500°F for 4 hours and 1000°F for 1 hour. The additional 45 minutes at 1000°F will buy precious time
in the event of a re.

Steel Wheel: The wheel is a standard duty, all-welded wheel (standard duty and high pressure belt drive). The blades are curved for
improved air performance while increasing their strength and rigidity. The wheel assembly is fully welded to provide extremely durable
and consistent performance. The wheel is dynamically balanced. Balancing weights are mechanically attached to the inside of the rims

of both the backplate and wheel inlet. This allows a precise placement of the weights anywhere within a full 360° range on two separate

planes, without the possibility of detachment.

Forced Motor Cooling: Motors and drive components are located out of the airstream in a separate compartment. Two cooling tubes
are located between the motor dome and discharge apron which enables fresh air to be drawn into the motor compartment during fan
operation. This allows the cooler outside air to wash over the motor and bearings. This positive cooling promotes longer life for the motor
and drive components.

High Wind Construction

High wind construction Fumex fans are specically designed for high wind hurricane zones (HWHZ). The Fumex models are designed

to withstand 150 MPH winds in accordance with Miami-Dade and Florida Building Code standards. The units are 3rd party tested and

certied through a 3rd party Professional Engineer (P.E.) to meet these strict standards. Installation details are provided and since there are
no tie downs or external braces required for attaching the unit to the roof or curb this makes installation simple and easy. A wide range
is oered to meet all of your ventilation needs which includes all belt and direct drive sizes 36 and under.

Belt Drive Fumex Cutaway Direct Drive Fumex Cutaway

Product Certications:

18) Miami-Dade NOA # 14-0311.03

19) Florida Product Approval #12339

20) Texas Department of Insurance # RV-48

www.PennBarry.com 12

MOTOR AVAILABILITY

Green Plus Electronically Commutated Motor

The Green Plus (GP) option utilizes EC motors to provide signicantly greater
eciency, exibility, and controllability over standard direct drive permanent split

capacitor (PSC) motors. Using the included potentiometer, the Green Plus motors

can be turned down to as low as 80% the max operating speed while maintaining
90% eciency through the operating range. Additionally, the Green Plus can accept

0-10V input to tie to building management systems, not only allowing for savings in
direct fan energy consumption but reducing the exhaust of conditioned air during

o peak hours as well. All Green Plus motors come in open enclosure for usage with
115V-208V/230V, single phase, 50/60 Hz applications.

G

plus

Model HP

FX08VGP 1/6 - X X

FX08S/RGP 1/6 - X X

FX08QGP 1/6 - X X

FX10VGP 1/6 - X X

FX10S/RGP 1/6 - X X

FX10QGP 1/6 - X X

FX11V/S/RGP 1/6 - X X

FX11QGP 1/4 - X X

FX13V/S/RGP 1/6 - X X

FX13QGP 1/4 - X X

FX16VGP 1/6 - X X

FX16S/RGP 1/3 X X X

FX16Q1GP 1/2 X X X

FX16Q2GP 3/4 X - X

FX18VGP 3/4 X X X

ODP

110-120V

1-Phase

TE

110-120V

208-480V

TE

www.PennBarry.com 13

MOTOR AVAILABILITY

Variable Speed Motor Control

PennBarry oers Lek-Trol™ solid state controllers to alter the high speed of most direct drive motors by as much as 50%. If variable speed
is required, check the Lek-Trol™ availability table below to verify that controllers exist for the fan model selected. Remember, Lek-Trol™
controllers are currently only available for direct drive motors including all standard Open Drip Proof (ODP) 60 Hz motors. Not all totally

enclosed motors are currently available with variable speed control. Inverter rated motors suitable for use with variable frequency drives
can be supplied for belt drive models. Contact your local PennBarry representative for availability.

Available Lek-Trol™ Speed Controls

60 Hz 50 Hz

Model

FX08S - - - - - - - -

FX08R LT25 - - - - - - -

FX10S - - - - - - - -

FX10R LT30 LT30 LT35 LT35 LT35 LT30 LT35 LT35

FX11V - - - - - - - -

FX11S - - - - - - - -

FX11R LT30 - - - - - - -

FX11Q LT50 - - - - - - -

FX13V - - - - - - - -

FX13S - - - - - - - -

FX13R LT30 LT30 LT35 LT35 LT35 LT50 LT35 LT35

FX13Q LT45 LT50 LT35 LT35 LT35 LT50 LT35 LT35

FX16V - - - - - - - -

FX16S - - - - - - - -

FX16R LT50 - - - - - - -

FX16Q1 LT40 - - - - - - -

FX16Q2 LT75 - - - - - - -

FX18V LT60 - - - - - - -

Lek-Trols™ indicated for multi-speed models (eg., FX16V/S/R) are applicable only for the high speed. Do not use on low or medium speed for multi-speed
models. Items noted with ( - ) are not applicable.

ODP Totally Enclosed Totally Enclosed

115V 115V 200V 208V 230V 110V 220V 240V

www.PennBarry.com 14

DIRECT DRIVE | DIMENSIONS

L DIA

Fumex direct drive models are available with single and multi-speed motors.

A single Fumex fan may be made suitable for several requirements by a simple wiring change. This feature provides exibility for a variety
of reasons, including energy savings, o hours requirements, future expansion, or unexpected eld variations. When compared to belt

drive models, direct drive fans require less maintenance, have a simpler construction, cost less, and are lighter in weight.

Fumex direct drive models are available in six sizes (8, 10, 11, 13, 16, and 18). Their capacities are up to 4500 CFM, with static pressures up

to 1 1/2”.

L DIA

E Sq.

H

L DIA

G

1 ¼"

F Sq.

Wo

L DIA

E Sq.

H

L DIA

G

1 ¼"

F Sq.

Wo

FX13FX08-FX11

L DIA

E Sq.

G

1 ¼"

F Sq.

H

Wo

L DIA

E Sq.

L DIA

H

G

1 ¼"

F Sq.

Wo

FX16 FX18

Model L DIA H E Sq. Wo Sq. F Sq. G

FX08 25 14 1/8 18 1/2 9 16 7/8 24 16 Gauge 0.064” 0.050” 29 lbs.

FX10/ FX11 25 14 1/8 18 1/2 11 1/2 16 7/8 24 16 Gauge 0.064” 0.050” 32 /42 lbs. (1)

FX13 25 1/2 16 1/2 18 1/2 11 1/2 17 7/8 24 16 Gauge 0.064” 0.050” 45lbs.(2)

FX16 30 1/4 22 3/8 20 1/2 16 24 24 1/4 16 Gauge 0.064” 0.064” 69lbs.(3)

FX18 39 31 28 1/2 20 29 1/2 32 1/2 16 Gauge 0.064” 0.080” 87 lbs.

Galv. Steel

Base

Aluminum

Base

Discharge

Apron

Est. Ship

Weight

All dimensions are in inches.

(1) 11Q estimated ship weight = 44 lbs.

(2) 13Q estimated ship weight = 52 lbs.

(3) 16Q1 estimated ship weight = 71 lbs. 16Q2 estimated ship weight = 73 lbs.

Enhanced Direct Drives

Model L

FX081 35 28 3/4 24 3/4 16 27 1/4 30 5 3/4 15 3/4 56 16 gage 0.064 101

FX101 35 28 3/4 24 3/4 16 27 1/4 30 5 3/4 15 3/4 56 16 gage 0.064 101

FX121H 35 28 3/4 24 3/4 16 27 1/4 30 5 3/4 15 3/4 56 16 gage 0.064 116

FX131/H 35 28 3/4 24 3/4 16 27 1/4 30 5 3/4 15 3/4 56 16 gage 0.064 116

FX141 35 28 3/4 24 3/4 16 27 1/4 30 5 3/4 15 3/4 56 16 gage 0.064 118

FX161 39 31 28 1/2 20 29 1/2 32 1/2 6 1/2 19 3/4 145T 14 gage 0.064 151

FX181/H 39 31 28 1/2 20 29 1/2 32 1/2 6 1/2 19 3/4 145T 14 gage 0.064 152

FX241/H 46 34 1/2 33 1/2 25 35 7/8 36 7 24 3/4 184T 14 gage 0.064 200

DIA

H E

All dimensions are in inches

www.PennBarry.com 15

Sq.

Wo

Sq.

Sq.

F

G X Damper Size

Max Motor
Frame Size

Galv. Steel Base Discharge Apron

Est. Ship Weight

(lbs.)

BELT DRIVE | DIMENSIONS

L DIA

X

X

G

F Sq.

H

L DIA

Wo

E Sq.

Model L DIA H E Sq. Wo/ Ro F Sq. G X

FX08B 35 28 3/4 24 3/4 16 27 1/4 30 5 3/4 110

FX10B 35 28 3/4 24 3/4 16 27 1/4 30 5 3/4 115

FX12B 35 28 3/4 24 3/4 16 27 1/4 30 5 3/4 112

FX13B(HFT) 35 28 3/4 24 3/4 - - - 5 3/4 144

FX14B 35 28 3/4 24 3/4 16 27 1/4 30 5 3/4 145

FX16B 39 31 28 1/2 20 29 1/2 32 1/2 6 1/2 145

FX18B(H) 39 31 28 1/2 20 29 1/2 32 1/2 6 1/2 190

FX24B(H) 46 34 1/2 33 1/2 25 35 7/8 36 7 190

FX27B 53 1/2 35 1/2 36 1/2 - - - 6 1/2 219

FX30B 53 1/2 35 1/2 36 1/2 - - - 6 1/2 219

FX36B 66 47 1/2 44 1/2 - - - 5 1/2 470

Est. Ship Weight

(lbs)

(1)

(1)

(2)

(2)

(3)

(3)

(4)

(4)

(4)

(5)

(6)

Model Galv. Steel Base Aluminum Base Discharge Apron Damper Size (in.) Max Motor Frame Size

FX08B 16 Gauge 0.064” 0.064” 15 3/4 55

FX10B 16 Gauge 0.064” 0.064” 15 3/4 56

FX12B 16 Gauge 0.064” 0.064” 15 3/4 56

FX13B(HFT) 16 Gauge 0.064” 0.064” 15 3/4 56

FX14B 16 Gauge 0.064” 0.064” 15 3/4 56

FX16B 14 Gauge 0.080” 0.080” 19 3/4 145T

FX18B(H) 14 Gauge 0.080” 0.080” 19 3/4 145T

FX24B(H) 14 Gauge 0.080” 0.080” 24 3/4 184T

FX27B 14 Gauge 0.080” 0.080” 27 3/4 184T

FX30B 14 Gauge 0.080” 0.080” 27 3/4 184T

FX36B 12 Gauge 0.102” 0.080” 35 1/2 213T

All dimensions are in inches

(1) Add 8 lbs. for Heat and Smoke option

(2) Add 11 lbs. for Heat and Smoke option

(3) Add 20 lbs. for Heat and Smoke option

(4) Add 55 lbs. for Heat and Smoke option

(5) Add 65 lbs. for Heat and Smoke option

(6) Add 110 lbs. for Heat and Smoke option

www.PennBarry.com 16

FAN SELECTIONS

Model

FX = Fumex centrifugal roof exhaust upblast fan

Construction

Application

E = Exhaust / Relief
S = Supply / Intake

Application Flow (CFM)

<enter value>

Application Static Pressure (inwg)

<enter value>

Motor

Eciency

G = Green Plus (ECM)
P = Premium
S = Standard

Horsepower

0.020 = 1/50

0.033 = 1/30

0.050 = 1/20

0.040 = 1/25

0.083 = 1/12

0.091 = 1/11

0.143 = 1/7

0.167 = 1/6

0.200 = 1/5

0.250 = 1/4

0.333 = 1/3

0.500 = 1/2

0.750 = 3/4

01.00 = 1

01.50 = 1 1/2

02.00 = 2

03.00 = 3

05.00 = 5

07.50 = 7 1/2

10.00 = 10

15.00 = 15

20.00 = 20

25.00 = 25
X = Special

Drive Type

B = Belt
D = Direct
T = Belt w/Tensioner

Fan RPM

<####>

Motors and Drives

F = Factory mounted
L = Less motor less drive
M = Less motor with drive

Motor Enclosure

0 = None
1 = TE w/Overload
2 = TE w/o Overload
3 = ODP w/Overload
4 = ODP w/o Overload
5 = EXP C2D1
X = Special

Motor Tap

0 = None
K = 1650 RPM (Q1)
L = 500 RPM
M = 690 RPM
Q = 1750 RPM (Q2)
R = 1550 RPM
S = 1300 RPM
V = 1050 RPM
W = 860 RPM (W1,W2,W3)

Unit Size

8, 81, 10, 101, 11, 12, 121, 13, 131, 14,
141, 16, 161, 18, 181, 24, 241, 27, 30,
36

Wheel Width

0 = Standard
H = High pressure

Voltage/Phase/Cycle

1 = 380V/1PH/50HZ
2 = 400V/1PH/50HZ
3 = 415V/1PH/50HZ
4 = 460V/1PH/60HZ
B = 110V/1PH/50HZ*
C = 115V/1PH/60HZ
D=120V/1PH/60HZ*
F = 208V/1PH/60HZ
G = 208V/3PH/60HZ
H = 220V/1PH/50HZ*
J = 220V/3PH/50HZ*
K = 230V/1PH/60HZ
L = 230V/3PH/60HZ
M = 240V/1PH/50HZ*
N = 240V/3PH/50HZ*
P = 277V/1PH/60HZ*#
Q = 380V/3PH/50HZ*
R = 380V/3PH/60HZ*
S = 400V/3PH/50HZ*
T = 415V/3PH/50HZ*
U = 440V/3PH/50HZ*
V = 460V/3PH/60HZ
W = 480V/3PH/60HZ*
X = Special
Y = 575V/3PH/60HZ
* Non-standard offering subject to
longer lead times and price adjustment
# 277V applications require a
transformer

www.PennBarry.com 17

FAN SELECTIONS

Electrical Accessories

Controllers

0 = None
A = 0-10V output potentiometer
1 = Lek-Trol solid state speed

controller (mounted)

2 = Lek-Trol solid state speed

controller (loose)

3= Multi speed controller, iQ-MS

(ECM only)

4 = iQ-IPCM-no power supply (ECM

only)

5 = iQ-IPCM with 115V/230V power

supply (ECM only)

6 = iQ-IPCM with 277V power supply

(ECM only)

Options and Accessories

Construction Accessories

0 = None
A = Aluminum curb cap (standard)
F = Floating hinge kit (aluminum base)
G = Floating hinge kit (steel base)
H = Hinged sub-base (aluminum base)
J = Hinged sub-base (steel base)
S = Steel curb cap
W = Wall mounted adaptor

Curb

0 = None
C = Curb
Note: Curbs ordered separately on all
PLOPs

Damper

00 = None
D = Damper
XX = Special

Extended Lube Lines

0 = None
L = Extended lube lines

Guard/Screen

0 = None
B = Bird screen

Paint/Coating

0 = None
F = Epoxy powder coat (light gray)

7 = Provided by others
V = VFD (belt drive only)
Note: VFD can be ordered separately

Service Switches and ITW*

0 = None
1 = NEMA 1 ITW only
3 = NEMA 3R ITW only
A = NEMA 1 - loose
C = NEMA 1 - mounted and wired
D = NEMA 3R - loose
F = NEMA 3R - mounted and wired
G = NEMA 4 - loose
N = NEMA 7 - loose
Q = NEMA 9 - loose

G = Epoxy powder coat with UV

protection (gray)
H = Hi-temp powder coat (black)
J = Non-stick powder coat (clear)
K = Phenolic epoxy powder coat

(gray)
L = Phenolic epoxy powder coat with

UV protection (gray)
N = Polyester powder coat*
X = Special
* Colors only available in Polyester
Powder Coat

Paint Color*

00 = None
50 = Chrome green
55 = Pale green
56 = Dove gray (PPC standard)
61 = White
63 = Oxford beige
65 = Dover white
66 = Desert tan
70 = Black
73 = Smoke gray
77 = Brick red
79 = Peppercorn
81 = Pale brown
83 = Chocolate brown
85 = Timeless bronze
94 = Charcoal
X = Special
* Colors only available for polyester
powder coat

X = Special
* ITW - Internal wiring not provided on
explosion proof motors

Switches / Sensors

0 = None
A = Airminder switch (time delay)

B = Airminder+restat

F = Firestat switch

Transformer

0 = None
B = 277Vx115V

Pedestal

0 = None
A = Galvanized pedestal
B= Galvanized vented pedestal
C = Aluminum pedestal
D = Aluminum vented pedestal

Spare Belt(s)

0 = None
1 = 1 spare set
2 = 2 spare set

Special Applications

0 = None
2 = Restaurant exhaust (UL762)
4 = UL heat & smoke

Special Construction

0 = None
B = Spark resistance (AMCA B)
C = Spark resistance (AMCA C)
D= Spark resistance (AMCA C) + high

wind (Miami-Dade)

E= Spark resistance (AMCA B) + high

wind (Miami-Dade)

H = High wind (Miami-Dade)

Stainless Steel

0 = None
B = Hardware & shaft
H = Hardware
S = 304SS Shaft
X = Special

www.PennBarry.com 18

PENNBARRY PRODUCT SOLUTIONS

Commercial

Roof & wall exhaust centrifugal fans

Ceiling, wall, & inline centrifugal fans

Roof supply centrifugal fans

Square & round centrifugal fans

Wall mounted axial fans

Hooded roof axial fans

Upblast roof axial fans

Gravity ventilators

Roof curbs

Industrial

Freestanding centrifugal fans

Industrial & material handling fans

Tubular centrifugal inline fans

Mixed ow centrifugal fans

Plug & plenum fans

Wall mounted propeller fans

Tube axial fans

Vane axial fans

Bifurcator fans

Lab exhaust

Kitchen ventilation

Make-up air units

Exhaust fans

Energy recovery

Outdoor units

Indoor units

PennBarry is proud to be your preferred manufacturer of commercial and industrial fans and blowers. Learn how PennBarry

can assist you in your next application by contacting your PennBarry Representative or visiting us on the web at www.pennbarry.com

PennBarry | www.pennbarry.com | [e-mail] | Tel [phone] | Fax [phone]

PennBarry reserves the right to make changes at any time, without notice, to models, construction, specications, options and availability.

This document illustrates the appearance of PennBarry products at the time of publication. View the latest updates on the PennBarry website.

© 2018 PennBarry. All rights reserved. FUMEX OCTOBER 2018.