Pelonis FZ10-9LR Owner's Manual

1

OWNER'S MANUAL

36" OSCILLATING TOWER FAN

MODEL: FZ10-9LR

READ AND SAVE THESE INSTRUCTIONS

SAFETY INFORMATION

PACKAGE CONTENTS

CAUTION

• Do not leave the fan running unattended.

• Do not use fan in a window. Rain may create an electrical hazard.

• This is not a toy. Keep out of the reach of children and pets.

• Do not insert any object or body parts in the grilles of the fan while the fan is plugged in.

• This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of
electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does
not fit fully into the outlet, reverse the plug. If the plug still does not fit, contact a qualified
electrician. Do not attempt to bypass this safety feature.

WARNING

2

3

1. Do not operate any fan with a damaged cord or plug. Discard fan or return to
an authorized service facility for examination and/or repair.

2. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar
coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area
and where it will not be tripped over.

3. Fan should be used under rated voltage.

4. Connect power after the fan is fully assembled.

5. Never insert fingers, pencils, or any other object through the guard when fan is running.

6. Unplug from outlet when not in use, when moving fan from one location to another, before putting
on or taking off parts, and before cleaning.

7. Disconnect fan when removing grilles for cleaning.

8. Be sure fan is on a stable surface when operating to avoid overturning.

9. DO NOT use fan in window, rain may create electrical hazard.

RULES FOR SAFETY OPERATION

ASSEMBLY INSTRUCTIONS

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and diagram above. If any part is missing or damaged, do not attempt
to assemble the product. Contact customer service for replacement parts.
Estimated Assembly Time: 10 minutes

Fig. 2

1. Pull power cord (E) out slightly.

2. Put front base (B) onto rear base (C) and join them together.

3. Put the round base on the body (A) by inserting the cylinders under

(A) to blind holes on the round base as shown on diagram.

4. Fix (A) with base clip (D) as shown.

A

B

C

E

D

OPERATING INSTRUCTIONS (Fig. 3)

Fig. 3

CARE AND MAINTENANCE

• Always unplug the fan before cleaning.

• Do not allow water and steam to drip on or into the fan motor housing.

• Do not use any of the following as a cleaner: gasoline, paint thinner, benzine.

• Periodically clean this fan by lightly running a vacuum cleaner nozzle over the fan

grilles to remove any dust or dirt that may have accumulated inside or on the unit.

• Wipe all parts with a soft cloth.

• Dry all parts completely before reassembling or reconnecting the fan to the wall outlet.

• Keep surfaces dry and clean for a longer-lasting finish.

Proble

TROUBLESHOOTING

m Possible Cause Corrective Action

The fan will not
operate.

The fan isn’t plugged in and/or the
electrical outlet isn’t working properly.

Make sure the fan is plugged in and/or
the electrical outlet is working properly.

The fan will not
operate.

Obstructions stop the fan from working. Check for obstructions. If you find an

obstruction, turn the fan off.
Unplug the fan and carefully remove the
obstruction. Plug the fan in and turn it
on again by referring to the operating
instructions.

INSERT BATTERIES (Fig. 4)

Fig. 4

Notes:

.

ICON FUNCTION

Power

Speed Setting

Wind Mode

Timer

Oscillating

DETAIL

Press this key to turn the fan on/off

Press this key to desired fan speed,

1 = Low, 2 = Medium, 3 = High

Press this key to desired wind mode in the

sequence of NORMAL-BREEZE ( ) -SLEEP ( )

Press this key repeatedly to set the timer

from 1 hour to 8 hours

Press this key to start or stop the fan oscillation

1. Grasp plug and remove from the wall outlet.
Do not unplug by pulling on cord.

2. Open fuse cover. Slide open fuse access cover on top of attached
plug toward blades.

3. Remove fuse carefully. Push the fuse from the other side or turn
fuseholder over to remove fuse.

4. Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse.

5. Close fuse cover. Slide closed the fuse access cover on top of attached plug.

6. Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that should not be
removed. Discard product if the attached plug is damaged.

WARNING: This appliance has a polarized plug (one blade is wider than the other). The polarized
plug is not intended to be used in non-polarized outlets (having both slots the same size). To reduce
the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug, if it still does not fit, contact a qualified electrician. Do not
modify the plug in any way.

USER SERVICING INSTRUCTIONS

Battery
Compartment Cover

Batteries

Remote Control

1. Press down on the battery compartment cover and slide it out.

2. Insert the batteries, making sure that the positive terminals are facing
the proper direction marked inside the battery compartment.

3. Close the cover by sliding it in.

1) Use 2 “AAA” batteries (NOT INCLUDED).

2) Do not mix old and new batteries.

3) Do not mix alkaline, standard (carbon-line) or rechargeable
(nickel-cadmium) batteries.