Page 1
PELONIS
OWNER’S MANUAL
9" Window Fan
With Remote Control
And Filter
Model No.FW23-A4R
READ AND SAVE THESE INSTRUCTIONS
Page 2
NOTE:
This equipment has been tested and found to comply with the limits for a Class B
esigned to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
l interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television,
off and on, the user is encouraged to try
the receiver is
Read Rules for Safe Operation and Instructions Carefully.
CAUTION
IMPORTANT SAFETY INF
ORMATION
RULES FOR SAFE OPERATION
1. Never insert fingers, pencils, or any other object through the grille when fan is running.
2. Disconnect fan when moving from one location to another.
3. Disconnect fan when removing louvers and filters for cleaning.
OVERHEAT PROTECTION
The fan motor is equipped with a thermal fuse that turns the fan off in case of overheating. If
overheating occurs, please send the fan in for repair (refer to the Service & Support sections of
this manual).
WARNING
1. To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed
control device.
2. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of
electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
Do not attempt to defeat this safety feature.
3. Do not leave the fan running unattended.
4. Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
digital device, pursuant to Part 15 of the FCC Rules. These limits are d
used in accordance with the instructions, may cause harmfu
which can be determined by turning the equipment
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
connected.
- Consult the dealer or an experienced radio TV technician for help.
INSTALLATION INSTRUCTION
1. It is designed to fit a double-hung, slider and casement window with minimum openings of
25.35 inches wide and 12.7 inches high. It is recommended to use with your window screen
in place.
2. It is almost fully assembled and ready for immediate installation.
Page 3
3. The package includes two plastics feet,
which are needed when the fan is placed on
a surface rather than in a window.
ⅠUSED IN AWINDOW
1. Each side has two locks. Release the locks
at either one side or two sides to pull out the
extenders.
2. Put the locks back to fix the extender at desired length.
ⅡUSED AT SURFACE
The fan can be used at a surface besides a window. In this situation, just snap the two plastic feet
at the bottom of the fan body. No tools needed.
Figure 1
OPERATING INSTRUCTION
Plug it into an outlet. The red LED will display “ROOM”and two digits; this is the indoor
temperature.
ⅠPANEL OPERATION
The fan has two reversible motors. The rotation speed
and direction of each motor are controlled
independently using panel operation.
1. SPEED CONTROL
The three speeds— low (L), medium (M) and high (H)
are controlled by the left/right speed buttons and
showed by relevant left/right speed lights. For
example, when the light beside “L”is on, the speed is
low. When you press the “ON/SPEED1/OFF” /
“ON/SPEED2/OFF”button, the left/right motor starts
at low speed. Press the button repeatedly to select
the speed; the sequence of speed is low, medium,
high and off.
2. DIRECTION CONTROL
To exhaust, press the “DIRECTION1”/“DIRECTION2” button. Change the air direction by
pressing the button repeatedly.
To make the air exchange, set the two motors to
rotate in opposite direction.
3. TEMPERATURE SETTING
The fan can be set at any temperature from 65℉to 90℉. Press the “TEMP”button for several
seconds until the temperature LED starts blinking. Now the word “SET”shows while “ROOM”
disappears. Each time you press the “TEMP+” / “TEMP-” button, the temperature will
increase/decrease by 1℉. When it reaches a desired temperature, press “TEMP”button to stop
the blink and so the setting is confirmed. The two motors will be turned off automatically when the
Figure 2
Page 4
indoor temperature reaches the setting. Once the temperature departs the setting, the fan will
turn on automatically.
4. TURN-OFF
When the left/right motor is low/medium/high, press the “ON/SPEED1/OFF”/ “ON/SPEED2/OFF”
button three times/twice/once, then the left/right speed light is off and the left/right motor stops.
ⅡREMOTE CONTROLLER OPERATION
The remote controller is more convenient than the panel except it cannot be used to set the
temperature.
1. Press the “ON/OF”button to start the fan. The two motors will take in the air at the low speed.
2. To change the speed of left/right motor, press “SPEED1”/“SPEED2”button. Repeat and then
press to select the speed; the sequence of speed is low, medium and high.
3. To exhaust air, press the “DIRECTION1”/“DIRECTION2”button. Change the air direction by
pressing the button repeatedly.
4. To stop the fan, press the “ON /OFF”button.
INSERT THE BATTERIES
Press down on the battery compartment cover and slide it out.
1. Insert the batteries (not included in the package), and make
sure that the batteries are placed in the right way.
2. Slide back the battery cover.
Notes: Use size "AAA" alkaline or standard (carbon-zinc)
batteries. Do not mix old and new batteries. Do not mix alkaline,
standard (carbon-zinc), or rechargeable (nickel cadmium)
batteries.
Figure 3
The batteries should be removed from the remote controller and disposed of
safely before they are flat.
CLEANING
1. Be sure to unplug from the electrical supply source before cleaning.
2. Plastic parts should be cleaned with mild soap and damp cloth or sponge. Thoroughly remove
soap film with clean water.
3. To disassemble each part, reverse the order of assembly.
4. Be sure not to let water or other liquid enter the inside of motor.
5. To clean the filter:
1) Take of the small round plastic plate at the center of the louver by rotating it
counter-clockwise.
2) Use screwdriver to take off the screw and pick up the plastic washer (above) and metal
washer.
3) Take the louver and find the filter behind it. Clean them with mild soap and damp cloth or
sponge. Thoroughly remove soap film with clean water.
4) When the filter is dry, reverse the assembly order.
Page 5
Model No.: FW23-A4R
SPECIFICATIONS
SERVICE
&
SUPPORT
Voltage: 120v, 60Hz
For usage tips about this fan, to register your fan warranty online, or to obtain information about
other Pelonis Appliances products, please visit our website at
www.pelonis.com.
In the event of a warranty claim or if service is required for this fan, please contact us at the
following:
Toll Free: 866-876-4332 (M-F 9:00am to 5:00pm CST)
Email us at: service@pelonis.com
For questions or comments, please write to:
Pelonis Appliances, INC.
Att: Consumer Relations Department
2617N Great Southwest Parkway
Suite 100
Grand Prairie, TX 75050, USA
For your records, staple your sales receipt to this manual and record the following:
DATE OF PURCHASE: _____________________________________________
PLACE OF PURCHASE:_____________________________________________
(STAPLE SALES RECEIPT HERE)
NOTE: PROOF OF PURCHASE IS REQUIRED FOR
ALL WARRANTY CLAIMS
Page 6
ONE(1) YEAR LIMITED WARRANTY
Please read all instructions before attempting to use this product.
Please return the Warranty Registration card within fifteen (15) days from the date of
purchasing this product.
Pelonis Appliances, INC., referred to hereafter as Pelonis Appliances, warrants as limited herein
to the original purchaser of retail that each new FW23-A4R Window Fan, shall be free of defects
in material and workmanship for a period of one (1) year from the date of original purchase. This
one (1) year warranty is limited to the fan motor, fan blades, and electric control circuit board.
In the event of malfunctions or failure of your FW23-A4R Window Fan, simply deliver or send the
product, postage prepaid along with PROOF OF PURCHASE, within the warranty period of one
(1) year, to Pelonis Appliances. Pelonis Appliances reserves the right to inspect the claimed
defective part or parts to determine if the defect or malfunction complaint is covered by this
warranty. Pelonis Appliances shall, within sixty (60) days after receipt of the product, at its option,
repair and/or replace the defective part or parts free of charge. This warranty shall only cover
defects arising from normal usage.
Pelonis Appliances assumes no responsibility whatsoever if the FW23-A4R Window Fan should
fail during the warranty period by reasons of:
Misuse, negligence, physical damage or accidents.
Lack of maintenance (see cleaning).
Repair by any unauthorized party during the warranty period.
Damage caused by connection to an improper input voltage (see specifications).
Pelonis Appliances makes no further warranties or representations, express or implied except
those contained herein. No representative or dealer is authorized to assume any other liability
regarding the FW23-A4R Window Fan. The duration of the implied warranty granted under State
law, including warranties of merchantability and fitness for particular purpose are limited in
duration should the duration of the express warranty grant it hereunder. Pelonis Appliances shall
in no event be liable for direct, indirect, special or consequential damages.
Some states do not allow limitations on how long an implied warranty lasts, and/or the above
limitations or exclusion may not apply to you. This warranty gives you specific legal rights and you
may have other rights, which vary from state to state.
Should your FW23-A4R Window Fan fail to operate under the terms of this limited warranty,
contact Pelonis Appliances at 866-876-4332 (M-F 9:00am to 5:00pm CST).
Loading...