Pelco SS5729L, SS5723L, SS5729 User Manual

®

SS5723/SS5729

SS5723L/SS5729L

Series Sun Shroud

Installation/Operation

Manual C1419M (6/95)

1.0 WARNINGS

Prior to installation and use of this product, the follow­ing WARNINGS should be observed.

1. Installation and servicing should only be done by Quali­fied Service Personnel and conform to all Local codes.

2. Please thoroughly familiarize yourself with the
information in this manual prior to installation.

2.0 SCOPE

The information contained within this manual covers
the SS5723, SS5729, SSS723L and SS5729L Sun
Shroud installation.

2.1 DESCRIPTION

The Sun Shrouds are designed for use with the EH5723L
and EH5729L Legacy® Series enclosures. The sun
shroud protects the enclosure form the direct rays of
the sun and reduces the internal temperature by approxi­mately 10° to 15°F (-12.2° to -9.4°C) .

3.0 INSTALLATION

To install the sun shroud, perform the following steps:

NOTE: Use the four (4) 10-32 x .375 Phillips
head screws and nylon washers from the en­closure assembly.

1. Unlatch the enclosure lid and raise.

2. Remove the four (4) 10-32 screws from the enclo­sure lid (see diagram above).

3. Align the screw holes in the sun shroud and enclo­sure lid.

4. Install the screws as shown in the diagram above.

Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • [phone] or (1-559) 292-1981

FAX [phone] or (1-559) 292-3827

International customers call (1-559) 292-1981 or FAX [phone]

4.0 WARRANTY AND RETURN
INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved
defective in material or workmanship for a period of one year after the date
of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex

keyboard).

• Three years on Camclosure

CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,
and MC3651H-2X camera models, which have a five-year warranty.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy

DF5/DF8 Series fixed dome products.

• Two years on Spectra

ing when used in continuous motion applications.

• Two years on Esprit

wiper blades).

• Eighteen months on DX Series digital video recorders, NVR300

Series network video recorders, and Endura
network-based video products.

• One year (except video heads) on video cassette recorders (VCRs).

Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in

continuous motion applications (that is, preset scan, tour and auto scan
modes).

Pelco will warrant all replacement parts and repairs for 90 days from the
date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to Pelco, Clovis, California. Repairs made necessary by
reason of misuse, alteration, normal wear, or accident are not covered
under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or
loss resulting from the specific use or application made of the Products.
Pelco’s liability for any claim, whether based on breach of contract,
negligence, infringement of any rights of any party or product liability,
relating to the Products shall not exceed the price paid by the Dealer to
Pelco for such Products. In no event will Pelco be liable for any special,
incidental or consequential damages (including loss of use, loss of profit
and claims of third parties) however caused, whether by the negligence
of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The
Dealer may also have additional rights, which are subject to variation from
state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289­9100 or [phone] to obtain a Repair Authorization number (RA),
and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice

number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall
under the warranty conditions stated above, please include a written
explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by
which the item was received by Pelco.

®

Series products (multiplexers, server, and

®

and fixed camera models, except the

®

, CM6700/CM6800/CM9700 Series matrix, and

®

, Esprit®, ExSite™, and PS20 scanners, includ-

®

and WW5700 Series window wiper (excluding

™

Series distributed

RETURNS

In order to expedite parts returned to the factory for repair or credit, please
call the factory at [phone] or [phone] to obtain an
authorization number (CA number if returned for credit, and RA number
if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking
and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the
assigned CA or RA number and freight should be prepaid. Ship to the
appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto
Rico, send goods to:

If you are located outside the continental U.S., Alaska, Hawaii or Puerto
Rico and are instructed to return goods to the USA, you may do one of the
following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:

If the goods are to be sent by a FREIGHT FORWARDER, send the goods
to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

Pelco, the Pelco logo, Camclosure, Esprit,
Genex, Legacy, and Spectra are registered
trademarks of Pelco.
Endura and ExSite are trademarks of Pelco.

© Copyright 1999, Pelco. All rights reserved.

2 Pelco Manual C1419M (6/95)