Pelco SS4722L, SS4718L, SS4722 User Manual

®

SS4718/SS4718L/SS4722/SS4722L

Sun Shroud and

TI47 Thermal Insulation

Installation/Operation Manual

C1409M-C (7/98)

1.0 WARNINGS Prior to installation and use of this product, the following WARNINGS should be

observed.

1. Installation and servicing should only be done by qualified service personnel
and conform to all local codes.

2. Only use replacement parts recommended by Pelco.

Please thoroughly familiarize yourself with the information in this manual prior to
installation and operation.

2.0 DESCRIPTION The information contained within this manual covers the SS4718, SS4722, SS4718L,

SS4722L Sun Shrouds and the TI47 Thermal Insulation Kit installation.

The SS4718, SS4722, SS4718L, and SS4722L Sun Shrouds provide an air space
between the sun shroud and the enclosure to protect the enclosure from the direct
rays of the sun and reduce the internal temperature by approximately 10 to 15°F
(-12.2° to -9.4°C).

The TI47 Thermal Insulation Kit provides an improved resistance to heat loss through
the body of the enclosure by adding a 1/4-inch thick polyurethane insulation to the
majority of the internal surfaces.

Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • www.pelco.com
In North America and Canada: Tel [phone] • FAX [phone]

International Customers: Tel [phone] or FAX [phone]

3.0 INSTALLATION

3.1 SS4718/SS4722/ The sun shroud is supplied with two (2) threaded spacers and two (2) Phillips head
SS4718L/SS4722L screws.
SUN SHROUDS

To install the sun shroud, perform the following steps (refer to Figure 1).

1. Unlatch and raise enclosure lid.

2. Remove the two (2) screws, nylon washers, nuts and lock washers from the lid
of the enclosure.

3. Attach the threaded spacers to the under side of the sun shroud with the two
(2) screws and nylon washers previously removed, threading them through
the top of the sun shroud.

4. Align the spacers in the sun shroud with the holes in the enclosure lid. Attach
the sun shroud to the enclosure lid with the remaining lock washers and screws.
Tighten screws securely.

3.2 TI47 THERMAL The TI47 thermal insulation sheets are designed to be used with both 18-inch
INSULATION (45.72 cm) and 22-inch (55.88 cm) EH4700 Series enclosures. If insulation is

required for an 18-inch enclosure, the insulation must be cut along the factory-

NOTE:

The camera mounting sled

must be removed for proper installa-

marked perforation. For 22-inch installations, no trimming is necessary. To install
the thermal insulation, perform the following steps:

tion of the thermal insulation, there­fore, it should be done prior to the
enclosure installation.

3.2.1 Lid Insulation 1. Unlatch the enclosure lid and raise.

Installation

2. Pop the gas spring off of the lid at the ball-joint connection. Make sure the lid is
supported and not allowed to lay completely open - doing so will damage the
lid hinge.

3. Remove the adhesive backing from the “lid” insulation pad (see Figure 2).

4. Position the insulation around the sun shroud fasteners on the inside of the lid. It
may help to hold the insulation in a folder manner while positioning. Remove the
necessary punch-out holes in the insulation to accommodate the fasteners.

Figure 2. Lid Insulation InstallationFigure 1. Sun Shroud Installation

2 Pelco Manual C1409M-C (7/98)

3.2.2 Body Insulation 1. Remove the long, 1.5-inch wide, strip of insulation for the side panel from the
Installation lid insulation pad.

2. To adjust the length of the insulation pad (or the side panel), tear the insulation
along the perforations from the end(s) of the pad to fit either the 18-inch ver­sion or the Legacy® version of the enclosure.

3. Position the pad around the press nuts in the center of the body by folding the
pad along its length. Position the insulation punch-out(s) to closely match the
position of the press nuts.

4. Remove the adhesive backing, and carefully lay the insulation in the body of
the enclosure, pressing firmly, taking care not to crease the insulation.

5. Then apply the side strip to the side of the enclosure body that does not con­tain the “T-slot”. (See Figure 3.)

6. The insulation is very soft and will conform as needed during the installation of
the camera and lens.

7. Snap the gas spring ball joint to the lid, and close the enclosure.

3.2.3 Temperature Standard EH4700/EH4700L enclosure operating temperature: -10° to 120°F (-23°
Specifications to 48.8°C).

Temperature increase inside enclosure with heater operating:

17°F (9.5°C) increase with vent grills installed.

25°F (13.8°C) increase with vent covers and TI47 thermal insulation installed.

35°F (19.4°C) increase with vent covers, TI47 thermal insulation and WD47
defroster installed.

Figure 3. Installation of TI47 Thermal Insulation

Pelco Manual C1409M-C (7/98) 3

4.0 WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex

• Three years on Camclosure
CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a five­year warranty.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy
dome products.

• Two years on Spectra
continuous motion applications.

• Two years on Esprit

• Eighteen months on DX Series digital video recorders, NVR300 Series network video

recorders, and Endura

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications
(that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment.
All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs
made necessary by reason of misuse, alteration, normal wear, or accident are not covered under
this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the
specific use or application made of the Products. Pelco’s liability for any claim, whether based on
breach of contract, negligence, infringement of any rights of any party or product liability, relating
to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event
will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss
of profit and claims of third parties) however caused, whether by the negligence of Pelco or
otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or [phone]
to obtain a Repair Authorization number (RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty
conditions stated above, please include a written explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received
by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at (800)
289-9100 or [phone] to obtain an authorization number (CA number if returned for credit,
and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number

and freight should be prepaid. Ship to the appropriate address below.

Pelco, the Pelco logo, Camclosure, Esprit,
Genex, Legacy, and Spectra are registered
trademarks of Pelco.
Endura and ExSite are trademarks of Pelco.

© Copyright 1998, Pelco. All rights reserved.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed
to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

®

Series products (multiplexers, server, and keyboard).

®

and fixed camera models, except the CC3701H-2, CC3701H-2X,

®

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed

®

, Esprit®, ExSite™, and PS20 scanners, including when used in

®

and WW5700 Series window wiper (excluding wiper blades).

™

Series distributed network-based video products.

4 Pelco Manual C1409M-C (7/98)