Pelco SS3515, SS3512 User Manual

INSTALLATION/OPERATION

SS3508/SS3512/SS3515

®

Sun Shroud

C1437M-B (6/02)

INSTALLATION

The SS3508, SS3512 and SS3515 sun shrouds protect the EH3508, EH3512 and EH3515 enclosures from the direct rays of the sun and
reduce the internal temperature of the enclosures approximately 10° F (-12.22° C).

The sun shroud is supplied with the following:
2 Threaded spacers
2 Phillips head screws
2 Nylon washers

To install the sun shroud refer to Figure 1 and do the following:

1. Unlatch and raise the lid of the enclosure.

2. Remove the two screws, nylon washers, nuts, and lock washers from the lid of the enclosure. Do not discard the screws, nylon
washers, and lock washers, because they are required to install the sun shroud.

3. Install the hardware on the enclosure lid:

a. Place a lock washer onto one of the screws previously removed from the enclosure lid.

b. Insert the screw through a hole from the inside of the enclosure lid.

c. Place a nylon washer (previously removed from the enclosure lid) and then a spacer (supplied with the sun shroud) onto the

screw and tighten.

d. Repeat steps a-c to install the hardware on the other side of the enclosure lid.

4. Slide the sun shroud over the top of the enclosure lid. Align the spacers in the enclosure lid with the holes in the sun shroud.

5. Attach the sun shroud to the enclosure lid with the nylon washers and screws supplied with the sun shroud. Tighten screws securely.

SCREW

NYLON WASHER

SUN SHROUD

ENCLOUSURE

SPACER
NYLON WASHER

LOCK WASHER

SCREW

Figure 1. Detailed Assembly of a SS3508/SS3512/SS3515 Sun Shroud and an EH3508/EH3512/EH3515 Enclosure

WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment. Exceptions to this warranty are
as noted below:

• Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and MC3500/MC3600
Series); two years on all other cameras.

• Three years on Genex® Series (multiplexers, server, and keyboard).

•Two years on cameras and all standard motorized or fixed focal length lenses.

•Two years on Legacy®, Camclosure™ Camera Systems, CM6700/CM6800/CM8500/CM9500/
CM9740/CM9760 Matrix, DF5 and DF8 Series Fixed Dome products.

•Two years on Spectra®, Esprit™, and PS20 Scanners, including when used in continuous
motion applications.

•Two years on WW5700 series window wiper (excluding wiper blades).

• Eighteen months on DX Series digital video recorders.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applica­tions (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the
specific use or application made of the Products. Pelco’s liability for any claim, whether based on
breach of contract, negligence, infringement of any rights of any party or product liability, relating
to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no
event will Pelco be liable for any special, incidental or consequential damages (including loss of
use, loss of profit and claims of third parties) however caused, whether by the negligence of
Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or [phone] to
obtain a Repair Authorization number (RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions
stated above, please include a written explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received by
Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289­9100 or [phone] to obtain an authorization number (CA number if returned for credit, and RA
number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and
freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico:

Intermediate Consignee Ultimate Consignee

American Overseas Air Freight Pelco
320 Beach Road 3500 Pelco Way
Burlingame, CA 94010 Clovis, CA 93612-5699
USA USA

REVISION HISTORY

Manual # Date Comments

C1437M 6/95 Original version.
C1437M-A 6/97 Revised manual.
C1437M-B 6/02 Revised installation instructions. Updated format.

® Pelco, the Pelco logo, Spectra, Genex, and Legacy are registered trademarks of Pelco. © Copyright 2002, Pelco.
™ Esprit and Camclosure are trademarks of Pelco. All rights reserved.

®

World Headquarters

3500 Pelco Way

Clovis, California 93612 USA

USA & Canada

Tel: [phone]

Fax: [phone]

International

Tel: [phone]

Fax: [phone]

www.pelco.com

ISO9001

Orangeburg, New York Las Vegas, Nevada Eindhoven, The Netherlands Wokingham, United Kingdom Montreal, Canada