Pelco SD436-PRE0, SD436-PRE0-X, SD436-PRE1, SD436-PRE1-X, SD429-PRE0 Specsheet

PRODUCT SPECIFICATION

Pressurized Spectra® IV SE Series

BACK BOX AND LOWER DOME

camera solutions

Product Features

• Pressurized to 8 psig (55 kPa)

• Solid-State Sensors for Internal Temperature, Pressure, and

Dew Point

• On-Demand Environmental Status Display for Internal Temperature,

Pressure, and Dew Point

• On-Screen Alert Modes

• On-Screen Programmable Menus for Pan/Tilt, Camera, and Sensor

Alert Settings

• Built-in Back Box Memory

• Integrated Passive UTP Circuit

• 2 Auxiliary Outputs and 7 Alarm Inputs

• Environmental Pendant Style Back Box

• Stainless Steel Construction

• Meets NEMA Type 6P and IP67 Standards

• Compatible with 29X and 36X Spectra

• Built-in Power Line Surge and Limited Lightning Protection

• Fiber Optic Feedthrough Models Available

®

IV SE Dome Drives

10.50 (26.7)

11.63
(29.5)

5.96 (15.1)

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS;

ALL OTHERS ARE IN INCHES.

Pelco’s Pressurized Spectra® IV SE Series dome system provides
ultimate protection of the camera optics and electronics from
moisture, corrosive gases, and airborne contaminants. Domes are
easily pressurized with dry nitrogen to 8 psig (55 kPa) before or after
installation to stabilize the environment inside the system.

Sensors strategically placed in the dome system send an “Alert”
message when changes in internal pressure, temperature, or dew
point are beyond factory-set acceptable limits. The sensors also allow
for instant on-screen display of internal temperature, pressure, and
dew point.

The components of the Pressurized Spectra IV SE Series include
an environmental pendant style back box and a lower dome designed
for optimum optical clarity. All stainless steel construction provides
added protection in harsh environments.

The back box features a sun shroud, heater, and fan to maintain a
consistent operating environment. The back box also features built-in
back box memory, an integrated passive UTP circuit, two auxiliary
outputs, seven alarm inputs, and is compatible with all Spectra IV SE
Series dome drives.

The lower dome features an innovative O-ring seal and a stainless
steel V-band to create a reliable pressure seal. The V-band has a
unique latching system with one captivated fastener making lower
dome installation easy. Accessible on the lower dome trim ring are a
Schrader valve for system purging and a pressure relief valve.

The Pressurized Spectra IV SE Series is supplied with a prewired
cable with mating connector. The cable includes all wires for system
functionality, including power, alarms, auxiliaries, coaxial video, UTP
video, and serial control.

Also available are pressurized back box models with fiber optic
feedthrough that allow Pelco’s FS85011A and third-party fiber optic
transmitters to be installed inside the back box. These models include
either a 9/125 µm single-mode or 62.5/125 µm multimode fiber optic
cable with an ST-type connector.

International Standards

Organization Registered Firm;

ISO 9001 Quality System

C3421 / REVISED 12-21-12

TECHNICAL SPECIFICATIONS

SYSTEM MODEL NUMBERS

Back Box Type

Environmental Pendant, Pressurized

Environmental Pendant, Pressurized
Fiber Optic Feedthrough, Single-Mode

Environmental Pendant, Pressurized
Fiber Optic Feedthrough, Multimode

Lower

Dome

Smoked SD429-PRE0 SD436-PRE0

Clear SD429-PRE1 SD436-PRE1

Smoked SD429-PRSE0 SD436-PRSE0

Clear SD429-PRSE1 SD436-PRSE1

Smoked SD429-PRME0 SD436-PRME0

Clear SD429-PRME1 SD436-PRME1

29X Day/Night

COMPONENT MODEL NUMBERS

Back Box Lower Dome Dome Drive*

BB4-PR-E Environmental pendant, gray,

pressurized

BB4-PRS-E Environmental pendant, gray,

pressurized, fiber optic
feedthrough, single-mode

BB4-PRM-E Environmental pendant, gray,

pressurized, fiber optic
feedthrough, multimode

*For PAL and CCIR models add “-X” suffix to part number (for example: SD436-PRSE0-X or DD429-X)

†

To order a fixed mount system, refer to the component models above and select a back box model, a lower dome model, and the DD5-FM dome drive.
DD5-FM accepts camera and lens combinations including a BNC connector up to 12.70 x 6.99 x 6.99 cm (5.00" D x 2.75" W x 2.75" H).

LD53PR-0 Lower dome with smoked bubble
LD53PR-1 Lower dome with clear bubble

†

36X Day/Night

†

DD429 Day/night (NTSC) camera (29X)
DD436 Day/night (NTSC) camera (36X)

†

Removable, fixed mount bracket only

DD5-FM

(camera and lens not included);
interchangeable with all Spectra IV dome
drives

ELECTRICAL

Input Voltage 18 to 32 VAC; 24 VAC nominal

Input Power

24 VAC 23 VA nominal (without heater);

24 VDC 0.7 A nominal (without heater)
Fuse 1.25
Auxiliary Outputs 2
Alarm Inputs 7

22 to 27 VDC; 24 VDC nominal

73 VA nominal (with heater)

A

GENERAL

Construction

Back Box and Lower Dome Type 316L stainless steel

bble Polyc

Bu

Ligh

t Attenuation 1 F-stop (smoked); zero light loss (clear)

arbonate, 0.0

V-Band Type 316L stainless steel

Pressure Relief Brass

Schrader Valve Brass

Connector Nickel-plated steel
Mounting 1.5-inch NPT, threaded
Pressurization

Valve Schrader

Pressure 8 psig (55 kPa) (not factory pressurized)

Pressure Relief 10 psig (69 kPa)
Operating Temperature (Assumes no wind chill factor; for detailed

test conditions, contact Pelco)

Maximum 140°F (60°C) absolute maximum; 122°F

(50°C) sustained maximum

Minimum

F (–51.11°C) absolute minimum;

–60°
minimal icing at sustained minimum of –50°F
(–45°C); prevents icing at sustained minimum
of –40°F (–40°C); de-ices 0.1 inch (2.5 mm)
within 3 hours after power-up

90-inchthick

Weight (approximate) Unit Shipping

Back Box 10.2 lb (4.6 kg) 13 lb (5.9 kg)
Lower Dome 3.3 lb (1.5 kg) 7 lb (3.2 kg)

CERTIFICATIONS/RATINGS

• CE, Class B

• FCC, Class B

• UL/cUL Listed

•C-Tick

• S Mark for Argentina

• Meets NEMA Type 6P and IP67 standards

OPTIONAL ACCESSORIES

IPS-CABLE Remote monitor cable and software kit
IPS-RDPE-2
EH8000RKIT Dry nitrogen recharging kit (cannot be refilled)
TXB Series

FS85011A

Mounts IDM4012SS (stainless steel, wall),

†

If TXB or FS85011A boards are installed, it is not possible to upgrade system
operating software through the remote data port (IPS-RDPE-2).

†

†

Remote data port

Translator boards for AD Manchester, Hernis,

®

(Philips, Burle), TASS, and NTCIP

Bosch
protocols

†

Fiber transmitter sends one unidirectional
composite video channel and one
bidirectional data channel over one optical
fiber. Available in multimode and single-mode
versions

IWM Series (wall), MRCA (ceiling),
PP4348 (parapet roof), and
PP350/PP351 (parapet wall/roof)

Pelco by Schneider Electric

3500 Pelco Way, Clovis, California 93612-5699 United States

USA & Canada Tel [phone] Fax [phone]
International Tel [phone] Fax [phone]
www.pelco.com www.pelco.com/community

Pelco, the Pelco logo, and other tr ademarks associated with Pelco products referred

to in this publication are trademarks of Pelco, Inc. or its affiliates. ONVIF and the

ONVIF logo are trademarks of ONVIF Inc. All othe r product names and

Product specifications and availability are subject to change without notice.

services are the property of their respective co mpanies.

©Copyright 2012, Pelco, Inc. All rights reserved.