Pelco PMCL-RM17, PMCL-RM19 User Manual

INSTALLATION

PMCL-R Series
Monitor Mount

C2220M-A (1/06)

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Only use attachments/accesories specified by the manufacturer.

6. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the aparatus. When a cart is being used,
use caution when moving cart/apparatus combination to avoid injury from tip-over.

7. Installation should be done only by qualified personnel and conform to all local codes.

8. Use only installation methods and materials capable of supporting four times the maximum specified load.

9. Only use replacement parts recommended by Pelco.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage constituting a risk of electric shock is
present within this unit.

CAUTION:

This symbol indicates that there are important operating and maintenance instructions
in the literature accompanying this unit.

Description

The PMCL-R Series monitor mount is designed for installing PMCL Series flat panel, TFT LCD monitors in a standard 19-inch (48 cm) equipment
rack.

MODELS

PMCL-RM15 Kit for mounting a 15-inch (38 cm) monitor in a standard 19-inch (48 cm) equipment rack (7 RUs)
PMCL-RM17 Kit for mounting a 17-inch (43 cm) monitor in a standard 19-inch (48 cm) equipment rack (8 RUs)
PMCL-RM19 Kit for mounting a 19-inch (48 cm) monitor is a standard 19-inch (48 cm) equipment rack (9 RUs)

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

2 C2220M-A (1/06)

Installation

The following parts are supplied:

Qty Description

2 Preassembled rack mounts
8 Screws, 10-32 x 0.750-inch, Phillips, pan head, black
8 Nylon washers
4 Screws, M4 x 0.70 x 6 mm, Phillips, pan head, stainless steel
4 Lock washers

1. Tighten the lock nuts (refer to Figure 1) so they are loose enough to allow the brackets to move but tight enough to hold them in place.

2. Attach the rack mounts to the monitor using the four stainless steel, pan head screws and lock washers. Refer to Figure 1.

(4) LOCK WASHERS

(4) SCREWS,

M4 X 0.70 X 6MM,

PHILLIPS, PAN HEAD

(2) LOCK NUTS

Figure 1. Attaching Rack Mounts to Monitor

3. Attach the rack mounts to the equipment rack using the eight black, pan head screws and nylon washers. Align the top slots of the mounts
with mounting holes on the equipment rack that have 0.5-inch spacing below them. All eight mounting slots will align with the holes in the
rack only if the mounts are in the correct position.

4. Swivel the monitor forward or backward to position it to the proper viewing angle.

C2220M-A (1/06) 3

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex

• Three years on Camclosure
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.

•Two years on standard motorized or fixed focal length lenses.

•Two years on Legacy
fixed dome products.

•Two years on Spectra
continuous motion applications.

•Two years on Esprit

•Two years (except lamp and color wheel) on Digital Light Processing (DLP
lamp and color wheel will be covered for a period of 90 days. The air filter is not covered
under warranty.

• Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for
such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused,
whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.

®

Series products (multiplexers, server, and keyboard).

®

and fixed camera models, except the CC3701H-2,

®

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

®

®

, Esprit

®

and WW5700 Series window wiper (excluding wiper blades).

™

Series distributed network-based video products.

™

, ExSite

, and PS20 scanners, including when used in

®

) displays. The

If a warranty repair is required, the Dealer must contact Pelco at [phone] or
[phone] to obtain a Repair Authorization number (RA), and provide the following
information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the

warranty conditions stated above, please include a written explanation with the product
when returned.

Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at
[phone] or [phone] to obtain an authorization number (CA number if returned
for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

REVISION HISTORY

Manual # Date Comments

C2220M 11/05 Original version.
C2220M-A 1/06 Added information about aligning mounting holes properly.

Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. ©Copyright 2006, Pelco. All rights reserved.
Endura and ExSite are trademarks of Pelco.
DLP is a registered trademark of Texas Instruments, Inc.

Worldwide Headquarters • 3500 Pelco Way • Clovis, California 93612 USA • www.pelco.com

USA & Canada • Tel: [phone] • Fax: [phone]

International • Tel: [phone] • Fax: [phone]