Pelco PM200C User Manual

C224M-C (6/99) PM200C Light Duty Ceiling/Pedestal Mount
®
3500 Pelco Way, Clovis, CA 93612-5699 USA
In North America & Canada: Tel (800) 289-9100 FAX (800) 289-9150
International Customers: Tel (1-559) 292-1981 FAX (1-559) 348-1120
www.pelco.com
U
®
L
LISTED
IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following warnings should be observed.
1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.
2. Installation shall be done in accordance with all local and national electrical and mechanical codes utilizing only approved materials.
3. Use only installation methods and materials capable of supporting four times the maximum specified load.
5. To prevent damage from water leakage when installing a mount outdoors on a roof or wall, apply sealant around the bolt holes between the mount and mounting surface.
The product and/or manual may bear the following marks:
This symbol indicates that danger­ous voltage constituting a risk of electric shock is present within this unit.
This symbol indicates that there are important operating and main­tenance instructions in the litera­ture accompanying this unit.
Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.
CAUTION:
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
NOTE:
The two fasteners to secure the mount to the mounting surface (minimum 1/4" diameter recommended) and the three fasteners to secure a scanner (10-32 x 1.00") to the mount are
not supplied
. The three 1/4-20 x .625 Hex head bolts, flat washers and split lock washers for a pan/tilt are supplied.
DESCRIPTION
The PM200C is a light duty ceiling/pedestal mount designed for mounting light duty scanners and pan/tilts and is capable of handling loads up to 25 pounds (11.25 cm). The PM200C is designed for easy installation or removal and mounts to any horizontal surface.
INSTALLATION
When mounting the PM200C ceiling/pedestal mount make certain that the mounting surface is capable of supporting the full load of the mount, scanner, or pan/tilt and camera.
1. Drill holes in the mounting surface using the mount as a template and attach the mount securely with the recommended fasteners. (Refer to Figure 1 for mounting dimensions.)
If you install the mount outdoors, rain water could leak through the holes for the mounting bolts and damage the roof. This could be a problem only if the mounting bolts go completely through the roof.
To prevent water damage, seal the bolt holes with an appropriate sealant. Apply the sealant around the bolt holes between the mount and the mounting surface.
2. Attach the scanner or pan/tilt to the mount with the recommended fasteners.
HARDWARE KIT
Qty Description Part Number 3 1/4-20 x 5/8, Hex head bolts ZH1/420X.625CH 5 3/16 special size, flat washer ZH260X562X65C 5 1/4" washer, split lock ZH1/4LWSSL 2 1/4-20 nut ZH1/4-20NUTCH
Figure 1. PM200C Mounting Dimensions
WARRANTY AND RETURN INFORMATION
WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below:
• Five years on FT/FR8000 Series fiber optic products.
• Three years on Genex® Series products (multiplexers, server, and keyboard).
• Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a five-year warranty.
• Two years on standard motorized or fixed focal length lenses.
• Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.
• Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in continuous motion applications.
• Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
• Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura™ Series distributed network-based video products.months on DX Series digital video recorders, NVR300 Series network video recorders, Endura™ Series distributed network-based video products, and TW3000 Series twisted pair transmission products.
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800)289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.
RETURNS In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair). All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below. If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following: If the goods are to be sent by a COURIER SERVICE, send the goods to:
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
REVISION HISTORY
Manual # Date Comments
C224M-C 8/95 Revised outdoor mounting instructions and hardware kit.
6/99 Revised to new style.
Service Department Pelco 3500 Pelco Way Clovis, CA 93612-5699
Pelco 3500 Pelco Way Clovis, CA 93612-5699 USA
Pelco c/o Expeditors 473 Eccles Avenue South San Francisco, CA 94080 USA Phone: 650-737-1700 Fax: 650-737-0933
® Pelco, the Pelco logo, Spectra, Esprit, Genex, Legacy, and Camclosure are registered trademarks of Pelco. ™ Endura and ExSite are trademarks of Pelco. © Copyright 1999, Pelco. All rights reserved.
Loading...