C256M-C (4/99)
PM2000/PM2010
Universal Ceiling/Pedestal Mount
®
300 W. Pontiac Way,
Clovis, CA 93612-5699
USA
In North America & Canada:
Tel (800) 289-9100
FAX (800) 289-9150
DataFAX (800) 289-9108
International Customers:
Tel (1-559) 292-1981
FAX (1-559) 348-1120
DataFAX (1-559) 292-0435
Pelco Online
http://www.pelco.com
U
®
L
LISTED
IMPORTANT SAFEGUARDS AND WARNINGS
Observe the following warnings before installing and using this product.
1. Installation and servicing should be done by qualified installation and service personnel only.
2. Installation should be done according to all local and national electrical and mechanical
codes, using only approved materials.
3. Use only installation methods and materials capable of supporting four times the maximum weight of the equipment to be mounted.
4. Use stainless steel hardware to fasten the mount to outdoor surfaces.
5. To prevent damage from water leakage when installing a mount outdoors, apply sealant
around the bolt holes between the mount and the mounting surface.
The product and/or manual may bear the following marks:
This symbol indicates that dangerous voltage constituting a risk of
electric shock is present within this
unit.
This symbol indicates that there are
important operating and maintenance instructions in the literature
accompanying this unit.
Please thoroughly familiarize yourself with the information in this manual prior to installation
and operation.
CAUTION:
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
DESCRIPTION
The PM2000 and PM2010 universal ceiling/pedestal mounts are designed for use with
medium- to heavy-duty scanners and pan and tilt units and will safely support loads up to 125
pounds (57 kg). Using two or more ST1 support struts with the PM2000 can add stability to the
mount in high wind conditions. These universal mounts will accept the AH1000 and AH2000
adjustable heads for ceiling or pedestal mounting of camera enclosures or a PA2000 mount
adapter for use with the Legacy® integrated positioning system. Both mounts are constructed
of aluminum and have a gray polyester powder coat finish.
CAUTION:
Make
certain the mounting
surface is capable of
supporting the full load of the
ceiling/pedestal mount, scanner
or pan and tilt, and camera/
enclosure.
Models
PM2000 Universal ceiling/pedestal mount for use with medium- or heavy-duty scan-
ners and pan and tilt units; 24 inches (61.0 cm) in height
PM2010 Same as PM2000, except 10 inches (25.4 cm) in height
INSTALLATION
1. Determine the correct positioning of the ceiling/pedestal mount. For Legacy® and
medium-duty scanner and pan and tilt installations, the 8.5-inch (21.6 cm) diameter end
will be attached to the mounting surface. For heavy-duty pan and tilt installations, the 6.0inch (15.2 cm) diameter end will be attached to the mounting surface.
2. Using the PM2000 or PM2010 universal ceiling/pedestal mount as a template, drill holes
into the mounting surface.
3. Attach the ceiling/pedestal mount to the mounting surface with 5/16-inch diameter stainless steel fasteners (not supplied). To prevent water damage if installed outdoors, seal
the bolt holes with appropriate sealant (not supplied). Apply the sealant around the bolt
holes between the ceiling/pedestal mount and the mounting surface.
4. Attach ST1 support struts to the PM2000 mount as required for high wind conditions.
5. Refer to the AH1000/AH2000 manual for instructions to attach an adjustable head to the
ceiling/pedestal mount.
6. For a Legacy® integrated positioning system, attach a PA2000 mount adapter to the
Legacy® base with the four 1/4-20 screws provided with the mount adapter. Then attach the
mount adapter and Legacy® to the PM2000/PM2010 with suitable hardware (not supplied).
SPECIFICATIONS
Construction: Aluminum
Finish: Gray polyester powder coat
Maximum Load: 125 lb (57 kg)
Dimensions: See Figure 1
Weight:
PM2000 4.2 lb (1.9 kg)
PM2010 2.9 lb (1.3 kg)
PM2000 PM2010
Figure 1. PM2000/PM2010 Universal Ceiling/Pedestal Mount
WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of
shipment. Exceptions to this warranty are as noted below:
• Three years on Genex™ Series (multiplexers, server, and keyboard).
• Two years on all standard motorized and fixed focal length lenses.
• Two years on Esprit™, Legacy
CM8500/CM9500/CM9750/CM9760 Matrix, Spectra
Fixed Dome products.
• Two years on WW5700 series window wiper (excluding wiper blades).
• Two years on cameras.
• Six months on all pan and tilts, scanners or preset lenses used in continuous
motion applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date
of Pelco shipment. All goods requiring warranty repair shall be sent freight
prepaid to Pelco, Clovis, California. Repairs made necessary by reason of
misuse, alteration, normal wear, or accident are not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss
resulting from the specific use or application made of the Products. Pelco’s
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products.
In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may
also have additional rights, which are subject to variation from state to state.
®
, Intercept®, PV1000 Series, CM6700/
®
, DF5 Series and DF8
NOTE: VALUES IN PARENTHESES ARE
CENTIMETERS; ALL OTHERS
ARE INCHES
If a warranty repair is required, the Dealer must contact Pelco at (800) 2899100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and
provide the following information:
1. Model and serial number
2. Date of shipment, P .O. number, Sales Order number , or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall
under the warranty conditions stated above, please include a written explanation with the product when returned.
Ship freight prepaid to: Pelco
Method of return shipment shall be the same or equal to the method by which
the item was received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please
call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for
repair). Goods returned for repair or credit should be clearly identified with
the assigned CA/RA number and freight should be prepaid. All merchandise
returned for credit may be subject to a 20% restocking and refurbishing charge.
Ship freight prepaid to: Pelco
300 West Pontiac Way
Clovis, CA 93612-5699
300 West Pontiac Way
Clovis, CA 93612-5699
REVISION HISTORY
Manual # Date Comments
C256M-C 4/99 Added certifications. Added reference to PA2000 adapter. Revised manual to new format.
®Pelco and the Pelco logo are registered trademarks of Pelco. © Copyright 1999, Pelco. All rights reserved.