Pelco PXM100, CMXM100, PAXM100 User Manual

ExSite

™

Series Mounts
WXM100, CMXM100,
PAXM100, and PXM100

INSTALLATION

C2216M (5/05)

WXM100

C2216M (5/05) 3

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Only use attachments/accessories specified by the manufacturer.

6. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.

7. Installation should be done only by qualified personnel and conform to all local codes.

8. Use only installation methods and materials capable of supporting four times the maximum specified load.

9. Use stainless steel hardware to fasten the mount to outdoor surfaces.

CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any

servicing other that contained in the operating instructions unless you are qualified to do so.

10. Only use replacement parts recommended by Pelco.

The product and/or manual may bear the following marks:

WARNING: This symbol indicates that dangerous voltage constituting a

risk of electric shock is present within this unit.

This symbol indicates that there are important operating and maintenance
instructions in the literature accompanying this unit.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

4 C2216M (5/05)

Description

This manual contains the installation instructions for the following ExSite

™

Series mounts:

WXM100 Wall mount designed to mount the ExSite

Series system directly to a load-bearing vertical surface.

CMXM100 Corner adapter for use with the WXM100 to mount an ExSite Series system to the corner of a structure.

PAXM100 Pole adapter for use with the WXM100 to mount a system to a horizontal pole.

PXM100 Pedestal mount designed to mount an ExSite Series system directly to a horizontal surface in either an upright or inverted

position.

*Recommended strength of concrete is 3,600 psi or 25 Mpa.

**Minimum of 1/8-inch wall.

Model Supplied Hardware Mounting Surface Recommended Hardware

WXM100 None

Solid Concrete*

Five 3/8-16 x 1-9/16-inch long stainless steel drop-in anchors and five 3/8-16 x 1.0-inch
thread length, stainless steel hex head bolts with stainless steel lock washers

Steel I Beam**

Five 3/8-16 x 1.0-inch thread length, stainless steel hex head bolts with stainless
steel lock washers and 3/8-16 stainless steel nuts

CMXM100

Five 3/8-16 x 1.0-inch
thread length, stainless
steel hex head bolts with
lock washers to attach
the adapter to the
WXM100 wall mount

Solid Concrete*

Six 1/2-13 x 2-inch stainless steel drop-in anchors and six 1/2-13 x 1.0-inch thread
length, stainless steel hex head bolts with stainless steel lock washers

Steel I Beam**

Six 1/2-13 x 1.0-inch thread length, stainless steel hex head bolts with stainless
steel lock washers and 1/2-13 stainless steel nuts

PAXM100

Four 5/8-inch wide x
40-inch (101.6 cm) long
stainless steel straps to
attach the adapter to a
pole

Five 3/8-16 x 1.0-inch
thread length, stainless
steel hex head bolts with
lock washers to attach
the adapter to the
WXM100 wall mount

Steel pole with a
diameter between
4 and 9 inches
(10.16 to 22.86 cm)

Supplied

PXM100 None

Solid Concrete*

Five 3/8-16 x 1-9/16-inch long stainless steel drop-in anchors and five 3/8-16 x 1.0-inch
thread length, stainless steel hex head bolts with stainless steel lock washers

Steel I Beam**

Five 3/8-16 x 1.0-inch thread length, stainless steel hex head bolts with stainless
steel lock washers and 3/8-16 stainless steel nuts