Pelco IM-VEPM User Manual

INSTALLATION

IM-VEPM Environmental Pendant Mount Adapter

C2252M (1/11)

Contents

Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

User Supplied Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2 C2252M (1/11)

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Only use attachments/accessories specified by the manufacturer.

6. Installation should be done only by qualified personnel and conform to all local codes.

7. Use only installation methods and materials capable of supporting four times the maximum
specified load.

8. Only use replacement parts recommended by Pelco.

C2252M (1/11) 3

Description

The IM-VEPM pendant mount adapter is specifically designed for use with Sarix™ IM-E/IM-V Series
network dome cameras.

PARTS LIST

The following installation tools and parts are supplied:

Qty Description

1 IM-VEPM pendant mount adapter

1 Tube of anti-seize lubricant

2 Screws, 8-32 Phillips pan head

1 Installation manual

USER SUPPLIED PARTS LIST

The following installation tool and parts are needed but not supplied:

Qty Description

1 IM-E or IM-V Series network dome camera

1 IX-SC service cable

1 Phillips screwdriver

4 C2252M (1/11)

Installation

1

2

3

4

5

6

7

8

8 7 6 5

4 3

2 1

1

2

3

4

5

6

7

8

1

2

3

4

5

6

7

8

8 7 6 5 4 3 2 1

8

8

1

1

Table A.

Pin Function

1TX+

2TX–

3RX+

4PoE 1-2

5PoE 1-2

6RX–

7PoE 3-4

8PoE 3-4

1. Route the wiring through the IM-VEPM pendant mount adapter.

2. Apply anti-seize lubricant (supplied) to the threads of the IM-VEPM.

3. Thread the pendant mount adapter to a 1.5-inch NPT pipe.

Figure 1. Installing the Pendant Mount Adapter

4. Connect the network cable to the RJ-45 network port.

Figure 2. RJ-45 Pin Descriptions

C2252M (1/11) 5

5. If you are installing an IM10-E or IM10-V Series model, connect the necessary wiring for audio.

+

–

+

–

Figure 3. Line-In Audio Wiring

ì

Microphone

î

Amplifier

ï

600-Ohm Impedance Matching Transformer

ñ

Line In –

ó

Line In +

Figure 4. Line-Out Audio Wiring

ì

Speaker

î

Amplifier

ï

600-Ohm Impedance Matching Transformer

ñ

Line Out –

ó

Line Out +

6 C2252M (1/11)

6. Install the back box in the pendant mount adapter:
a. Align the back box screws with the two mounting screw holes on the pendant mount adapter.

b. Slide the back box into the pendant mount adapter.

c. Insert the two 8-32 Phillips pan head screws (supplied) through the holes in the back box.

d. Tighten the screws completely to secure the back box to the pendant mount adapter.

Figure 5. Installing the Back Box

7. Apply power to the camera.

NOTE: If the camera is not connected to a Dynamic Host Configuration Protocol (DHCP) server and
DHCP is enabled, the configuration sequence might take up to five minutes to complete.

C2252M (1/11) 7

8. Position the camera as needed:
a. View the camera image using the service port.

b. Manually rotate and tilt the camera module to position the camera. Do not over-rotate the

module.

WARNING: Excessively turning the module in one direction could result in damage to the wiring.

Figure 6. Adjusting the Pan and Tilt

ì

Pan 355°

î

Rotate 120°

ï

Tilt 164°

9. Adjust the field of view:
a. Loosen the zoom locking screw.

b. Turn the zoom adjustment ring clockwise or counterclockwise to adjust the field of view.

c. Tighten the zoom locking screw.

10. Focus the lens:
a. View the camera image using the service port or a Web browser.

b. Manually adjust the zoom and focus of the lens to the desired field of view.

c. The focus can be adjusted further using the settings in the Web interface.

8 C2252M (1/11)

11. Align the dome liner with the camera, and then snap it into place.

Figure 7. Installing the Dome Liner

12. Install the bubble and trim ring:
a. Place the bubble inside the trim ring.

b. Align the trim ring screws with the three mounting screw holes on the back box.

c. Push the bubble and trim ring onto the back box.

d. Use the 1/8-inch hollow hex bit (supplied with IM-E and IM-V Series cameras) to tighten the

tamper-resistant screws to secure the trim ring to the back box.

Figure 8. Installing the Lower Dome

C2252M (1/11) 9

Specifications

REVISION HISTORY

Manual # Date Comments

C2252M 1/11 Original version.

Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates.
All other product names and services are the property of their respective companies.
Product specifications and availability are subject to change without notice.
© Copyright 2011, Pelco, Inc. All rights reserve d.

The materials used in the manufacture of this document and its components are compliant to the requirements of
Directive 2002/95/EC.

MECHANICAL

Mounting Method Attach the IM-VEPM to a mount with 1.5 inch NPT pipe

GENERAL

Construction Aluminum

Finish Light gray polyester powder coat

Unit Weight 0.77 kg (1.69 lb)

NOTE: VALUES IN PARENTHESES ARE INCHES; ALL OTHERS ARE CENTIMETERS.

1.32

(0.52)

9.14

(3.60)

13.46 (5.30)

10 C2252M (1/11)

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, an y merchandise proved defective in material or workmanship for a period of one year after the date of
shipment.

Exceptions to this warranty are as noted below:

• Five years:
– Fiber optic products
– Unshielded Twisted Pair (UTP) transmission products
– CC370 1H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models

• Three years:
– Pe lco-designed fixed network cameras and network dome cameras with Sarix™ technology.
– Pe lco-branded fixed camera models (CCC1390H Series, C10DN Series, C10CH Series, and IP3701H Series)
– EH150 0 Series enclosures

®

– Spectra

IV products (including Spectra IV IP)

– Cam closure
– DX Series digital video recorders (except DX9000 Se ries which is covered for a period of one year), DVR5100 Series digital video recorders,

– En dura
– Ge nex® Series products (multiplexers, server, and keyboard)
– PMCL200/300/400 Series LCD monitors
– PMCL5xx Series FHD monitors

• Two years:
– S tandard varifocal, fixed focal, and motorized zoom lenses.
– DF5/DF8 Series fixed dom e products
– Lega cy® Series integrated positioning systems
– Spectra III™, Spectra Mini, Spectra Mini IP, Esprit®, ExSite®, and PS20 scanners, including when u sed in continuous motion applications.
– Espr it Ti and TI2500 Series thermal imaging products
– Espr it and WW5700 Series window wiper (excluding wiper blades).
– CM 6700/CM6800/CM9700 Series matrix
– Di gital Light Processing (DLP®) displays (except lamp and color wheel). The lamp and color wheel will be covered for a period of 90 days.

– Inte lli-M

•One year:
– Video cassette record ers (VCRs), except video heads. Video heads will be covered for a period of six months.

• Six months:
– Al l pan and tilts, scanners, or preset lenses used in continuous motion applicatio ns (preset scan, tour, and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to a Pelco designated locatio n. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are no t covered under
this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products
shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental, or consequential
damages (including loss of use, loss of prof it, and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with spe cific legal rights. The Dealer may also have additional right s, which are subject to variation from state
to state.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or [phone] to obtain a Repair Authorization number (RA), and
provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, sales order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product that does not fall un der the warranty conditions stated above, please include a writte n
explanation with the product wh en returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS

To expedite parts returned for repair or credit, please call Pelco at [phone] or [phone] to obtain an authorization number (CA number if
returned for credit, and RA number if returned for repair) and designated return location.

All merchandise returned for credit may be subject to a 20 percent restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid.

®

Series (IS, ICS, IP) integrated camera systems

Digital Sentry

The air filter is not covered under warranty.

®

Series hardware products, DVX Series digital video recorders, and NVR300 Series network video recorders

®

Series distributed network-based video pro ducts

®

eIDC controllers

2-10-10

www.pelco.com

Pelco by Schneider Electric 3500 Pelco Way Clovis, California 93612-5699 United States

USA & Canada Tel [phone] Fax [phone]

International Tel [phone] Fax [phone]