Pelco IM-PMWT, IM-PMBL User Manual

INSTALLATION

IM-PMWT/IM-PMBL Pendant Mount Adapter

C2243M-A (2/10)

Contents

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Cat5 Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Audio Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2 C2243M-A (2/10)

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Only use attachments/accessories specified by the manufacturer.

6. Installation should be done only by qualified personnel and conform to all local codes.

7. Use only installation methods and materials capable of supporting four times the maximum
specified load.

8. Only use replacement parts recommended by Pelco.

C2243M-A (2/10) 3

Description

The IM-PMWT and IM-PMBL are pendant mount adapters designed for use with the IM Series network
dome camera. When used with the appropriate hardware, the mounts are compatible with 0.75-inch or
25 mm conduit.

MODELS

IM-PMWT Indoor white pendant mount
IM-PMBL Indoor black pendant mount

PARTS LIST

Remove all of the contents from the shipping box.

Qty Description

1 IM-PMWT or IM-PMBL pendant mount adapter
2 Screws, M4 x 16 mm, Phillips pan head
1 Installation manual

Installation tools, mounting hardware, and the following parts are needed but not supplied:

Qty Description

1 IM Series network dome camera
1 0.75-inch or 25 mm conduit fitting (including a threaded pipe nipple and nut)
1 IX-SC service cable
1 Phillips screwdriver

4 C2243M-A (2/10)

Installation

1. Prepare the pendant mount adapter:

a. Place a threaded pipe nipple (not supplied) into the top of the pendant mount adapter.

b. Screw the pipe nut (not supplied) securely onto the bottom of the threaded pipe nipple.

Figure 1. Preparing the Pendant Mount Adapter

2. Prepare the IM Series network dome camera:

a. Remove the surface mount ring from the back box of the dome camera.

b. Turn the lower dome 45 degrees, and then remove the lower dome from the back box.

c. Remove the dome liner from the back box.

3. Pull all wiring through the pipe, conduit fitting, and pendant mount adapter and terminate all wires
(if not already terminated).

4. Attach the IM-PMWT or IM-PMBL pendant mount adapter with conduit fitting to 0.75-inch or 25 mm
conduit.

5. Connect the wiring to the back box (refer to Wiring on page 8).

C2243M-A (2/10) 5

6. Install the back box into the pendant mount adapter:

a. Line up the back box screws with the two mounting screw holes on the pendant mount

adapter.

b. Slide the back box into the pendant mount adpater.

c. Insert the two M4 x 16 mm Phillips pan head screws (supplied) through the holes in the

back box.

d. Tighten the screws completely to secure the back box to the pendant mount adapter.

Figure 2. Installing the Back Box

7. Apply power to the camera. The camera will complete a configuration sequence: the green LED
flashes five times per second for approximately two minutes and then turns off after the sequence is
complete.

NOTE: If the camera is not connected to a Dynamic Host Configuration Protocol (DHCP) server and DHCP
is enabled, the configuration sequence might take up to five minutes to complete.

6 C2243M-A (2/10)

8. Install the dome liner:

a. Insert the dome liner tabs into the slots in the camera module.

b. Press the dome liner until you hear it snap into place.

Figure 3. Installing the Dome Liner

9. Install the lower dome:

a. Align the lower dome with the camera.

b. Press the lower dome into place against the trim ring.

c. Turn the lower dome 45 degrees to conceal the service port, reset button, and NTSC/PAL

button.

Figure 4. Installing the Lower Dome

10. To complete the installation, refer to the IM Series Installation/Operation manual.

C2243M-A (2/10) 7

WIRING

8

8

1

1

CAT5 CABLE

Connect a Cat5 cable to the RJ-45 network port. The 8-pin connector includes video and
Power over Ethernet (PoE) for the camera. PoE (IEEE 802.3af) injects power over the same cabling
that carries the network data, eliminating the need for a separate power supply. This simplifies
the installation and operation of the camera without affecting network performance.

NOTE: The camera will autosense and configure itself to use either a crossover cable or a
straight cable.

Refer to Figure 5 for pin descriptions.

1

2

3

4

5

6

7

8

8

7

6

5

4

3

2

1

Pin Function

1TX+

2TX–

3RX+

4 PoE 1-2

5 PoE 1-2

6RX–

7 PoE 3-4

8 PoE 3-4

Figure 5. Cat5 Cable Pin Descriptions

8 C2243M-A (2/10)

AUDIO WIRING

If you are not using the built-in microphone, the IM Series also supports line-in audio using standard
unshielded twisted pair (UTP) cable and a 600-ohm impedance matching transformer. Audio functionality
is only available for IM10 Series models, and it can be enabled or disabled using the Web browser.

NOTE: Improper use of audio/visual recording equipment may subject you to civil and criminal penalties.
Applicable laws regarding the use of such capabilities vary between jurisdictions and may require, among
other things, express written consent from the recorded subjects. You are solely responsible for insuring
strict compliance with such laws and for strict adherence to any/all rights of privacy and personalty.

Figure 6. Line-In Audio Wiring

ì

Microphone

î

Amplifier

ï

600-Ohm Impedance Matching Transformer

ñ

Audio UTP Cable

C2243M-A (2/10) 9

Specifications

MECHANICAL

Mounting Method Requires a 0.75-inch or 25 mm conduit fitting (not supplied) to

GENERAL

Construction ABS plastic
Finish

IM-PMWT White
IM-PMBL Black

Unit Weight 0.24 lb (0.11 kg)

(Design and product specifications subject to change without notice.)

attach the mount adapter to 0.75-inch or 25 mm conduit.

4.98

4.98

(12.65)

(12.65)

4.87

4.87

(12.37)

(12.37)

Ø 3.22

Ø 3.22

(8.18)

(8.18)

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE IN INCHES.

REVISION HISTORY

Manual # Date Comments

C2243M 12/09 Original version.
C2243M-A 2/10 Revised the lower dome installation instructions per CN24047 to reflect design change.

10 C2243M-A (2/10)

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, an y merchandise proved defective in material or workmanship for a period of one year after the date of
shipment.

Exceptions to this warranty are as noted below:

• Five years:
– Fiber optic products
– Unshielded Twisted Pair (UTP) transmission products
– CC370 1H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models

• Three years:
– Pe lco-designed fixed network cameras and network dome cameras with Sarix™ technology.
– Pe lco-branded fixed camera models (CCC1390H Series, C10DN Series, C10CH Series, and IP3701H Series)
– EH150 0 Series enclosures

®

– Spectra

IV products (including Spectra IV IP)

– Cam closure
– DX Series digital video recorders (except DX9000 Se ries which is covered for a period of one year), DVR5100 Series digital video recorders,

– En dura
– Ge nex® Series products (multiplexers, server, and keyboard)
– PMCL200/300/400 Series LCD monitors
– PMC L542F, PMCL547F, and PMCL552F FHD monitors

• Two years:
– S tandard varifocal, fixed focal, and motorized zoom lenses.
– DF5/DF8 Series fixed dom e products
– Lega cy® Series integrated positioning systems
– Spectra III™, Spectra Mini, Spectra Mini IP, Esprit®, ExSite®, and PS20 scanners, including when u sed in continuous motion applications.
– Espr it Ti and TI2500 Series thermal imaging products
– Espr it and WW5700 Series window wiper (excluding wiper blades).
– CM 6700/CM6800/CM9700 Series matrix
– Di gital Light Processing (DLP®) displays (except lamp and color wheel). The lamp and color wheel will be covered for a period of 90 days.

– Inte lli-M

•One year:
– Video cassette record ers (VCRs), except video heads. Video heads will be covered for a period of six months.

• Six months:
– Al l pan and tilts, scanners, or preset lenses used in continuous motion applicatio ns (preset scan, tour, and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to a Pelco designated locatio n. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are no t covered under
this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products
shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental, or consequential
damages (including loss of use, loss of prof it, and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with spe cific legal rights. The Dealer may also have additional right s, which are subject to variation from state
to state.

If a warranty repair is required, the Dealer must contact Pelco at (800 ) 289-9100 or [phone] to obtain a Repair Authorization number (RA), and
provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, sales order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product that does not fall un der the warranty conditions stated above, please include a written
explanation with the product wh en returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS

To expedite parts returned for repair or credit, please call Pelco at [phone] or [phone] to obtain an authorization number (CA number if
returned for credit, and RA number if returned for repair) and designated return location.

All merchandise returned for credit may be subject to a 20 percent restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid.

®

Series (IS, ICS, IP) integrated camera systems

®

Digital Sentry

The air filter is not covered under warranty.

Series hardware products, DVX Series digital video recorders, and NVR300 Series network video recorders

®

Series distributed network-based video pro ducts

®

eIDC controllers

1-22-10

Pelco, the Pelco logo, Camclosure, Digital Sentry, Endura, Esprit, ExSite, Genex, Intelli-M, Legacy, and Spectra are registered trademarks of Pelco, Inc.
Spectra III is a trademark of Pelco, Inc.
DLP is a registered trademark of Texas Instruments Incorporated.
All product names and services identified t hroughout this document are trademarks or registered trademarks of their re spective companies.
The absence of a trademark or registered trademark from this document does not constitute a waiver of intellectual property rights.
© Copyright 2010, Pelco, Inc. All rights reserved.

www.pelco.com

Pelco, Inc. Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA

USA & Canada Tel [phone] Fax [phone]

International Tel [phone] Fax [phone]