Pelco IMP521-1IS, IMP521-1ES, IMP321-1RS, IMP321-1IS, IMP321-1ES User Manual

...

C2292M-B-EN (12/16)

IMP121-1IS IMP221-1IS

IMP321-1IS IMP521-1IS

Sarix

Professional IMP

Series 3.75” Indoor Dome

User Manual

C2292M-B-EN (12/16)

IJP121-1IS

IJP221-1IS

Sarix

Professional IJP

Series 2” Micro Indoor Dome

User Manual

Contents

Important Notices Statement ........................................................................................................................................................ 5

Regulatory Notices .............................................................................................................................................................. 5

Radio and Television Interference ....................................................................................................................................... 5

Korean Class A EMC .................................................................................................................................................. 5

Warranty Statement ..................................................................................................................................................................... 5

UL Safety Notices ................................................................................................................................................................ 5

Preface ......................................................................................................................................................................................... 6

1. Product Overview .............................................................................................................................................................. 7

1.1 Dimensions .................................................................................................................................................................... 7

1.1.1 IMP Series 3.75” Indoor Dome ........................................................................................................................... 7

1.1.2 IJP Series 2” Micro Indoor Dome ....................................................................................................................... 7

1.2 Models Introduction ....................................................................................................................................................... 8

1.2.1 IMP Series 3.75” Indoor Dome ........................................................................................................................... 8

1.2.2 IJP Series 2” Micro Indoor Dome ....................................................................................................................... 8

1.3 Physical Characteristics ................................................................................................................................................. 9

1.3.1 IMP Series 3.75” Indoor Dome ........................................................................................................................... 9

1.3.2 IJP Series 2” Micro Indoor Dome ..................................................................................................................... 11

2. Installation and Connection ........................................................................................................................................ 12

2.1 Unpacking Everything .................................................................................................................................................. 12

2.1.1 IMP Series 3.75” Indoor Dome ......................................................................................................................... 12

2.1.2 IJP Series 2” Micro Indoor Dome ..................................................................................................................... 12

2.2 Optional Accessories ................................................................................................................................................... 13

2.2.1 IMP Series 3.75” Indoor Dome ......................................................................................................................... 13

2.2.2 IJP Series 2” Micro Indoor Dome ..................................................................................................................... 13

2.3 Installation - IMP Series 3.75” Indoor Dome ................................................................................................................ 13

2.3.1 Checking Appearance ...................................................................................................................................... 13

2.3.2 Disassembling the Camera .............................................................................................................................. 14

2.3.3 Connecting the Wires ....................................................................................................................................... 15

2.3.4 Mounting the Camera ....................................................................................................................................... 15

2.3.5 Adjusting the Camera Position ......................................................................................................................... 22

2.3.6 Adjusting the Focus .......................................................................................................................................... 23

2.3.7 Network Topology ............................................................................................................................................ 23

2.3.8 System Requirements ...................................................................................................................................... 24

2.4 Installation - IJP Series 2” Micro Indoor Dome ............................................................................................................. 25

2.4.1 Checking Appearance ...................................................................................................................................... 25

2.4.2 Disassembling the Camera .............................................................................................................................. 25

2.4.3 Connecting the Wires ....................................................................................................................................... 26

2.4.4 Mounting the Camera ....................................................................................................................................... 27

2.4.5 Adjusting the Camera Position ......................................................................................................................... 30

2.4.6 Network Topology ............................................................................................................................................ 30

2.4.7 System Requirements ...................................................................................................................................... 31

2.5 Connection ................................................................................................................................................................... 32

2.5.1 Default IP address ............................................................................................................................................ 32

2.5.2 Connecting From a Computer & Viewing Preparation ...................................................................................... 32

3. Administration and Configuration .............................................................................................................................. 34

3.1 Live .............................................................................................................................................................................. 34

3.1.1 Zoom and Focus Controls ................................................................................................................................ 35

3.2 Settings ........................................................................................................................................................................ 35

3.2.1 System ............................................................................................................................................................. 36

3.2.2 Network ............................................................................................................................................................ 39

3.2.3 Imaging ............................................................................................................................................................. 51

3.2.4 A/V Streams ..................................................................................................................................................... 59

3.2.5 Users ................................................................................................................................................................ 65

3.2.6 Events .............................................................................................................................................................. 68

Pelco Troubleshooting Contact Information ............................................................................................................................... 79

Important Notices Statement

For information about Pelco’s product-specific important notices and thereto related information, refer to www.pelco.com/legal.

REGULATORY NOTICES

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission’s rules.

CAN ICES-3(A)/NMB-3(A)

Korean Class A EMC

Warranty Statement

For information about Pelco’s product warranty and thereto related information, refer to www.pelco.com/warranty.

UL SAFETY NOTICES

The product is intended to be supplied by a Listed Power Unit marked "L.P.S." (or "Limited Power Source") and rated output 12Vdc/0.70A or 24Vac, 0.56A minimum or 48Vdc, 0.15A minimum.

The product shall be installed by a qualified service person and the installation shall conform to all local codes.

Preface

This user manual is to be used as a reference for the installation and manipulation of the camera unit including features, functions, and a detailed explanation of the menu tree.

This manual provides the following information:

 Product Overview: The main functions and system requirements of the unit.  Installation and Connection: Instructions on unit installation and wire connections.  Administration and Configuration: The main menu navigation and controls explanations.

1. Product Overview

1.1 Dimensions

1.1.1 IMP Series 3.75” Indoor Dome

The dimension of the Sarix® Professional Series 3.75” Indoor Dome camera is depicted within the Figure 1-1 below.

VALUES IN PARENTHESES ARE INCHES; ALL OTHERS ARE

FIGURE 1-1: PHYSICAL DIMENSIONS

1.1.2 IJP Series 2” Micro Indoor Dome

CENTIMETERS.

3.75” INDOOR DOME

The dimension of the Sarix® Professional Series IP 2” Micro Indoor Dome camera is depicted within the Figure 1-2 below.

VALUES IN PARENTHESES ARE INCHES; ALL OTHERS ARE

FIGURE 1-2: PHYSICAL DIMENSIONS

CENTIMETERS.

2” MICRO INDOOR DOME

1.2 Models Introduction

Model

Description

IMP121-1ES

1MP Indoor Dome with Vari-focal lens

IMP221-1ES

2MP Indoor Dome with Vari-focal lens

IMP321-1ES

3MP Indoor Dome with Vari-focal lens

IMP521-1ES

5MP Indoor Dome with Vari-focal lens

Model

Description

IJP121-1IS

1MP 2” Micro Indoor Dome

IJP221-1IS

2MP 2” Micro Indoor Dome

1.2.1 IMP Series 3.75” Indoor Dome

The physical appearance and installation methods for the IMP 3.75” Indoor Series models indicated within the list below are, by and large, the same. Therefore, please regard this manual where we use the example from IMP521-1IS as a reference to apply to all the varied models.

TABLE 1-1: MODELS LIST

1.2.2 IJP Series 2” Micro Indoor Dome

The physical appearances and installation methods for the IJP 2” Indoor models indicated within the list below are, by and large, the same. Therefore, please regard this manual where we use the example from IJP221-1IS as a reference to apply to all the models.

TABLE 1-2: MODELS LIST

1.3 Physical Characteristics

2 3 4 5 6

7 8 10

1.3.1 IMP Series 3.75” Indoor Dome

FIGURE 1-3: CAMERA CONNECTIONS AND FEATURES 1/4 FIGURE 1-4: CAMERA CONNECTIONS AND FEATURES 2/4

FIGURE 1-5: CAMERA CONNECTIONS AND FEATURES 3/4 FIGURE 1-6: CAMERA CONNECTIONS AND FEATURES 4/4

1. Back box: The bottom case of the camera.

2. Lens Base: The physical main body of the camera.

3. Torx Screws of Lens Base * 3: The screws for fixing lens base with back box.

4. Inner Liner: The inner adjustable liner to cover and beautify camera lens assembly.

5. Torx Screws of Top Cover * 3: The screws for fixing top cover with lens base.

6. Top Cover: The top cover of the camera.

7. Micro SD Card Slot: The slot is for inserting micro SD card for file storage.

8. Default & Reset Button:

 Default: Press the button for 6 seconds to restore the camera’s settings back to the factory default.  Reset: Press the button for below 1 second to reboot the camera.

9. Bottom Conduit Hole: The bottom hole for cable entry.

10. Side Conduit Hole: The side hole for cable entry.

11. Digital I/O Connectors:

 Audio In: Via “Au/I” and “GND” ports, connect to external device like microphone that receives sound for camera.  Audio Out: Via “Au/O” and “GND” ports, connect to device like speaker to be triggered through alarm output signals.  Alarm Out: Via “COM” and “AO” ports, connect to external device to be triggered through alarm output signals.  Alarm In: Via “GND” and “AI” ports, connect to external device that can trigger alarm input signals.

12. Power Terminal: The port is to connect with external either DC 12V or AC 24V power supply.

13. RJ-45 Network Port: Connect the RJ-45 connector to this port with a PoE (Class 2) compatible network

device that supplies power through the Ethernet cable.

14. LED Indicators:

 Green LED: With solid green, the LED indicates a live connection is established.  Orange LED: With flashing orange, the LED indicates data is being transmitted / received between camera

and Internet.

1.3.2 IJP Series 2” Micro Indoor Dome

1 2 3

4 5 6 7 8

FIGURE 1-7: CAMERA CONNECTIONS AND FEATURES 1/2 FIGURE 1-8: CAMERA CONNECTIONS AND FEATURES 2/2

1. Camera Body: The physical main body of the camera.

2. Bottom Conduit Hole: The conduit hole designed for bottom conduit cabling.

3. Top Cover: The upper dome cover for the camera.

4. Latch Buttons: The 2 latch bottoms along the 2 sides of top cover are the cruxes to disassemble the camera.

5. Side Conduit Hole: The conduit hole designed for side conduit cabling.

6. RJ-45 Network Port: Connect the RJ-45 connector to this port with a PoE (Class 2) compatible network

device that supplied power through the Ethernet cable.

7. Default & Reset Button:

 Default: Press the button for 6 seconds to restore the camera’s settings back to the factory default.  Reset: Press the button for below 1 second to reboot the camera.

8. Micro SD Card Slot: The slot is for inserting micro SD card for file storage.

9. Digital I/O Connectors:

 Alarm Out: Via “OUT” and “COM” ports, connect to external device to be triggered through alarm output signals.  Alarm In: Via “GND” and “IN” ports, connect to external device that can trigger alarm input signals.  Audio Out: Via “GND” and “OUT” ports, connect to device like speaker to be triggered through alarm output signals.  Audio In: Via “GND” and “IN“ ports, connect to external device like microphone that receives sound for camera.

2. Installation and Connection

2.1 Unpacking Everything

2.1.1 IMP Series 3.75” Indoor Dome

Check all items in the product box against the order form and the packing slip. In addition to this manual, the items below are included in the product box:

 3.75” Indoor Dome camera * 1  Plastic Anchor * 4  Flat Head Screw (Tapping Type) * 4  T10 Security Torx Wrench * 1  Mounting Template * 2  Terminal Block * 1  Conduit Hole Plug * 1  Important Notices Declaration * 1  Printed Quick Start Guide * 1  Supplemental Resources Sheet * 1  Important Safety Instruction * 1  ROHS Statement Slip * 1

Please contact your dealer if any items are missing.

2.1.2 IJP Series 2” Micro Indoor Dome

Check all items in the product box against the order form and the packing slip. In addition to this manual, the items below are included in the product box:

 Fixed Indoor Dome Camera * 1  Plastic Anchor * 2  Flat Head Screw (Tapping Type) * 2  Mounting Template * 1  Important Notices Declaration * 1  Printed Quick Start Guide * 1  Supplemental Resources Sheet * 1  Important Safety Instruction * 1  ROHS Statement Slip * 1

Please contact your dealer if any items are missing.

2.2 Optional Accessories

2.2.1 IMP Series 3.75” Indoor Dome

 IMPICM-1l: In-ceiling wall mount, for use with the indoor dome models  IMPPM-1l: Pendant adapter, for use with the indoor dome models  IMPLD2-0I: Lower dome (smoked)  IMPLD2-1I: Lower dome (clear)

2.2.2 IJP Series 2” Micro Indoor Dome

 IMPEBAP: 4S electrical box adapter for micro dome models  IMPPMB-1I: Wall mount L-shape bracket for micro indoor dome models

2.3 Installation - IMP Series 3.75” Indoor Dome

Following tools might help you complete the installation:

 A drill  Screwdrivers  Wire cutters

2.3.1 Checking Appearance

Although the protective materials used for the packaging should be able to protect the unit from most accidents during transportation, check the unit and its accessories for any visible damage. Remove the protective film to check items in accordance with the list in 2.1 Unpacking Everything.

2.3.2 Disassembling the Camera

1 3 4

Please refer to the steps with the figure below for the correct disassembling order.

1. Loosen the 3 camera top cover screws.

2. Gently pull the top cover downward to take it apart from the camera body.

3. Further loosen the 3 camera lens base screws.

4. Gently lift the camera lens base off from the back box.

FIGURE 2 - 1: DISASSEMBLING THE CAMERA

2.3.3 Connecting the Wires

1. Loosen the 3 top cover screws by torx wrench (supplied) followed by removing the top cover.

2. Lift to open the inner liner.

3. Loosen another 3 screws of camera lens base via torx wrench (supplied).

4. Remove the lens base from theback box.

After disassembling, the I/O interfaces will be seen on the rear of the lens base.

 Connect the power cable to the power port via one of the following 3 alternatives.

 AC 24V: Connect a power cable that supplies AC24V power source to the power terminal.  DC 12V: Connect a power cable that supplies DC12V power source to the power terminal.  PoE (Class 2): Connect an Ethernet cable terminated with RJ-45 connector to the PoE RJ-45 port for both power

supply and network connectivity purposes simultaneously.

 Insert audio in/out cables and alarm in/out cables to the corresponding terminals of the camera if required.

FIGURE 2 - 2: REAR SIDE FOR WIRING CONNECTION

2.3.4 Mounting the Camera

Step 1. Preparation by Disassembling

 Remove the camera housing, inner liner and bottom case.

FIGURE 2 - 3: DISASSEMBLING THE CAMERA

Step 2. Mark Mounting Area

 Use the guide pattern to prepare a mounting area for In-Ceiling Flush Mount.

1. Attach the mounting template on a desired mounting surface (normally for in-ceiling).

2. Drill a round hole (∅198mm) based on the template on the surface to have the camera embedded within the hole later.

FIGURE 2 - 4: MOUNTING TEMPLATE FOR FLUSH MOUNT

 Use the mounting template to prepare a mounting area for Surface Mount.

1. Place the supplied mounting template on a mounting surface. Drill 6 mm (0.2”) outer holes at the T1 or T2 template positions on the mounting surface. Then insert 4 or 2 supplied plastic anchors into the holes. (T1: for single-gang socket, T2: for double-gang socket, if applicable on mounting surface)

2. If you want to feed wiring from the hole on the top of the back box, create a circular opening corresponding to the “Bottom conduit hole” of mounting template on the mounting surface.

3. If feeding wiring from the side of the back box, you don’t need to drill a hole on the mounting surface. The “Side conduit hole” indication on the mounting template is for user to identify while mounting.

FIGURE 2 - 5: MOUNTING TEMPLATE FOR SURFACE MOUNT

Step 3. Mounting Schemes

Locking Arms

Tighten the screws to extend the locking arms

Method 1: Flush Mount (requires In-Ceiling mounting accessory)

1. Embed the in-ceiling mount bracket into the hole that was drilled based on the mounting template.

FIGURE 2 - 6: FLUSH MOUNT 1/3

2. Use a cross screw driver to turn the 2 bracket screws clockwise to extend the locking arms and tighten them securely to compress the locking arms so that the bracket can be fixed within the in-ceiling area firmly.

FIGURE 2 - 7: FLUSH MOUNT 2/3

3. Based on your needs, use the bottom conduit hole or side conduit hole on the back box for cable entry and

Protective Cover

Spring Hook * 2

Fix back box onto the in-ceiling bracket by securing the 4 screws.

Assemble lens base with lower case and fasten the 3 torx screws.

Further mount top cover onto lens base and tighten the 3 torx screws.

connect the required cables. NOTE: Please properly lock the conduit hole plug on the unused hole. For example, lock the side conduit hole with the plug while using the bottom conduit hole for cable entry and vice versa.

4. Fix the back box onto the in-ceiling bracket by fastening the 4 screws followed by aligning the identifying red dots of back box and lens base to properly assemble them together with securing the 3 lens base screws.

5. After adjusting focus position to the satisfied field of view, mount the top cover on the lens base, both of which have a red dot respectively also for aligning identification and tighten the 3 top cover screws firmly.

6. Attach the 2 spring hooks flanked the protective cover to the in-ceiling bracket for mounting completion.

NOTE: It is strongly recommended that you first ensure the mounting area is stable enough to withstand the in-ceiling bracket and locking arms clamping on the ground of safety concern.

FIGURE 2 - 8: FLUSH MOUNT 3/3

Method 2: Surface Mount

After cable entry and wiring, align the red dots of back box and lens base followed by securing the torx screws tightly.

After adjusting focus angle, align the red dots of lens base and top cover followed by fastening the torx screws to complete the procedure.

Safety-cord screw

FIGURE 2 - 9: SURFACE MOUNT

1. Based on your needs, use the bottom or side conduit hole on the back box for cable entry and connect the required cables first. Then mount the back box on a surface by securing screws (supplied) into the inserted plastic anchors tightly.

2. Align the back box and the lens base, both of which have a red dot on the top side respectively for aligning identification. Use the red dots to properly align them and then securely fasten the 3 screws of the lens base to the bottom case with torx key (supplied).

3. Adjust the focusing position by rotating, panning and tilting the camera lens base. When rotating the camera lens, do not rotate it over the stop point.

4. Fit the inner liner over the camera lens base until it snaps into the place.

5. Mount the top cover on the lens base, both of which similarly have a red dot for aligning identification. Be aware that the red dot of top cover is within interior instead of top side.

6. Use the torx wrench (supplied) to tighten the 3 top cover screws to complete mounting.

NOTE: Please properly lock the conduit hole plug on the unused hole. For example, lock the side conduit hole with

the plug while using the bottom conduit hole for cable entry and vice versa.

 If you possess a safety wire (sold separately), connect the safety wire with one end to the mounting surface

and the other end to the safety-cord screw of the camera in case of accidentally falling off.

FIGURE 2 -10: SAFETY-CORD SCREW

Method 3: Pendant Mount (requires pendant adapter mounting accessory)

Adaptor Ring

Apply Waterproof Repellent

Rubber O-Ring

Pendant Wall Mount

Pendant Pole Mount

The Pendant Installation involves mounting IMPPM-1l Sarix Indoor Pendant Mount for Indoor Dome camera. The camera must be first installed within the pendant mount back box with an adaptor ring before assembled with additional pendant mount brackets. Below are the recommended brackets, which are NOT provided, for additional pendant mount applications for your reference.

NOTE: Mounts and conduits must be sealed to prevent condensation in the camera

FIGURE 2-10: PENDANT MOUNT APPLICATIONS

1. Rotate the adaptor ring, which can connect with brackets of 1 1/2”-conform screw thread, clockwise to the pendant mount back box securely as shown below. The rubber o-ring provides seal on grooves between back box and adaptor ring. Note that it is highly suggested to apply waterproof repellent onto the upper screw thread as shown below for complete ingress protection. The diagram in the right side is the back box mounted with the adaptor ring.

FIGURE 2 -11: PENDANT MOUNT 1/2

NOTE: Anti-seize compound should be applied on pendant mount. Not doing so might prevent the unit from

being separated in the future. Waterproof tape can also be used to help prevent water ingress damage.

2. After wires connection, attach the lens base to the pendant mount back box by aligning the red dots for identification of both parts and securely fasten the 3 screws of the lens base with the torx wrench (supplied). Finally, assemble the top cover with the lens base, both of which, similarly, have red dots for aligning identification, followed by fastening the 3 screws of top cover to complete the installation.

FIGURE 2 -13: PENDANT MOUNT 2/2

2.3.5 Adjusting the Camera Position

A B C

The camera has three axes for adjusting field of view on different applications. While screening live view on your monitor, adjust the position using the procedures below simultaneously for desired focusing position.  Pan Adjustment (A)

Rotate the lens base until you are satisfied with the field of view. Note that the side conduit hole of back box is the point where the camera lens shouldn’t be rotated over.

 Horizontal Rotation (B)

Rotate 3D assembly in the lens base, but do not turn assembly more than 355° as this may have the internal cables twisted, disconnected, or broken.

 Tilt Adjustment (C)

Lift to open the inner liner, and tilt the camera lens to your desired angle. Restore the inner liner back to its default position after adjustment.

NOTE: Limitation for three axes position: Pan range: ±177°, Rotate range: ±177°, Tilt range: 35°～ 90°

FIGURE 2 – 14: ADJUSTING THE CAMERA POSITION

2.3.6 Adjusting the Focus

1. View the camera image using the browser (refer to 2.5 Connection on page 32).

2. Use the settings in the Web interface (refer to 3.2.3.4 Focus on page 56) to adjust the zoom and focus of the lens to the desired field of view.

3. Also, the focus can be adjusted by moving the zoom slider and using the Focus options in the live webpage. NOTE: Focus adjustment is done exclusively with Web UI.

2.3.7 Network Topology

The unit, which is equipped with Ethernet RJ-45 network interface, can deliver video images in real time via either Internet or Intranet. Please refer to the skeleton drawings shown below to enhance your understanding.

FIGURE 2-15: NETWORK TOPOLOGY

2.3.8 System Requirements

System Hardware

CPU

Intel® Pentium® 4 microprocessor, 2.4GHz or equivalent

RAM

1 GB or above

Monitor

Minimum of 1024 x 768 resolution, 16- or 32-bit pixel color resolution

System Software

Operating System

Microsoft Windows XP, Vista 32 and 64 bit, Win7 32 and 64 bit

Browser

Microsoft IE 9.0 and later

Media Player

Pelco Media Player or QuickTime® 7.6.5 for Windows XP, Windows Vista, and Windows 7; or QuickTime 7.6.4 for Mac OS X 10.4 (or later)

Unit

Power Supply

PoE / AC 24V /DC 12V

Note

1. All the installation and operations should comply with your local electricity safety rules.

2. Pelco Media Player is recommended for control, smoothness, and reduced latency as compared to QuickTime. The PMP is downloadable from Pelco web site: www.pelco.com/mediaplayer.

3. This product is not compatible with QuickTime version 7.6.4 for Windows XP or Windows Vista. If you have this version installed on your PC, you will need to upgrade to QuickTime version 7.6.5.

4. Network and processor bandwidth limitations might cause the video stream to pause or appear pixelated when additional Web-interface users connect to the camera. Decrease the images per second (ips), resolution, compression, or bit rate settings of the Web interface video streams to compensate for network or processor limitations.

The table below lists the minimum requirements to implement and operate a unit. Network and processor bandwidth limitations might cause the video stream to pause or appear pixilated when additional Web-interface users connect to the camera. Decrease the images per second (ips), resolution, compression, or bit rate settings of the Web interface video streams to compensate for network/processor limitations.

TABLE 2-1: SYSTEM REQUIREMENTS

+ 56 hidden pages