Pelco IMM12036-EBASUS, IMM12036-E-BASE, IMM12036-BASE, IMM12036-B1SUS, IMM12036-B1S User Manual
...
Optera IMM Installation
Parts List
All Models
Camera Lower Dome Documentation 2 Mac Address
Labels
In-Ceiling Models Surface Mounts Models Pendant Models
Back Box Mounting Plate Surface Mount Pendant Mount Anti-Seize Lubricant
T20 Bit 8-Pin Connector
Unsupplied Parts
All Models
• Pipe/conduit (if applicable)
• Conduit adapters (if applicable)
• Cat5 (or higher) cable, appropriately terminated for POE+
• 24 AWG, 8-wire multiconductor cable (if using alarm, relays, and/or audio)
• SD card, 32GB SanDisk Extreme
®
PLUS microSDHC™ UHS-I
Surface Mount Models Pendant Models
1 of the following mounting substrates and fasteners:
• Standard 4 in. square electrical box and appropriate fasteners
• Standard 2-gang electrical box and appropriate fasteners
• Any substrate using 3 standard screws, size M6 or 1/4 in.
INSTALLATION MANUAL
C2283M | 9/15
WMVE-SR Wall Mount (if using
the wall mount for environmental
and vandal-resistant models)
WMVE-SW Wall Mount (if using
the wall mount for indoor models)
Product Overview
R
PoE+
R
NOTICE: Pelco recommends installing the camera at a height of 3 meters (10 feet) or higher for best results. To ensure an unobstructed
view, the expected field of view should be at least 4 meters (12 feet) away from the camera.
- +
- +
A
- +
R
- +
R
Panomersive
with SureVision
To ensure reliable local storage, Pelco
recommends using a new 32 GB SanDisk
Extreme
®
PLUS microSDHC™ UHS-I card. If
• Flashes green: cycling power.
• Solid Green: power is active.
the card has been used or reformatted, local
storage may not function properly.
• Flashes green: network activity
Using a small tool, like a paper clip, press
once to restart the camera. Press and hold for
10 seconds to restore the camera to factory
settings.
• Solid amber: 1000 Mbps network connection
• Solid green: 100 Mbps network connection
• Red (solid or flashing): contact Pelco Product
Support at 1-800-289-9100 (USA and Canada)
or +1-559-292-1981 (international).
2
Wiring Information
Ø 15.24 cm
(6.00 in)
PoE+
Pin Function Pin PoE+ Mode A PoE+ Mode B
1 Audio Out– 1 TX+, PoE+ 1-2 TX+
2 Audio Out+ 2 TX–, PoE+ 1-2 TX–
3 Audio In– 3 RX+, PoE+ 3-4 RX+
4 Audio In+ 4 Not used PoE+ 1-2
5 Alarm Input 5 Not used PoE+ 1-2
6 Ground 6 RX–, PoE+ 3-4 RX–
7 Relay N.O. 7 Not used PoE+ 3-4
8 Relay Return 8 Not used PoE+ 3-4
Installing the In-Ceiling Mount
1.
3
2. Remove either the conduit plug (side) or grommet (top) for side or top wire entry.
3. Prepare the wire entry holes. If using the supplied grommet (plenum rating is not required), set the grommet aside for use later. If
using conduit (not supplied), replace with 25mm or 2/4 in. conduit adapters.
Installing the Back Box
1. Ensure that the support wings are rotated inward, and push the back box through the mounting hole.
2. Replace the other entry opening with the supplied conduit plug.
3. Tighten the two mounting screws to secure the back box using the supplied bit.
4. Feed the wires:
• If using conduit (not supplied): Feed wires through the conduit adapter, into the back box, and attach the conduit to the
adapter.
• If using the grommet (supplied): Feed the wires into the back box; pass the unterminated cables through the grommet; and
then insert the grommet.
5. Terminate the wires using an appropriate connector (not supplied).
4
Loading...