The information contained within this manual covers
the IH8 Series camera enclosure with integral mount.
1.1 WARNING
To insure safe operation, observe the following guidelines:
1Installation shall be done by qualified service
and installation personnel.
2.Installation shall be done in accordance with
all local and national electrical and mechanical codes utilizing only approved materials.
3.Use only installation methods and materials
capable of supporting four (4) times the maximum specified load.
4.Unless the unit is specifically marked as a
NEMA Type 3-6P enclosure, it is designed
for Indoor use only and it must not be installed
where exposed to rain and moisture.
5.Only use replacement parts recommended by
Pelco.
Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.
2.0 DESCRIPTION
The IH8 Series is a light duty camera enclosure with
integral mount designed for indoor use. The IH8 Series
can be used with 1/3-inch and 1/2-inch cameras and
will accommodate fixed focal length lenses with or
without auto-iris operation up to 5 inches in length.
This enclosure has a clamshell cover for easy access
when installing or servicing the camera/lens.
Also included in the unique design of this enclosure is
a cable feedthrough hole, a slotted camera bracket, and
an integral mount. The IH8 Series enclosure is constructed of .074 ABS plastic and the integral mount is
aluminum.
PELCO • 300 W. Pontiac Way, Clovis, CA 93612-5699 • (559) 292-1981 • (800) 289-9100
FAX (800) 289-9150 or (559) 292-3827 • DataFAX (800) 289-9108 or (559) 292-0435
2.1 MODELS
IH8-BLight duty, indoor camera en-
closure with integral mount for
fixed mounting applications,
black finish
IH8-WLight duty, indoor camera en-
closure with integral mount for
fixed mounting applications,
white finish
Cable Entry:Two (2) .593" diameter holes
(one in the enclosure and one in
the mount)
Suggested Mounting
Method:Secure to solid mounting sur-
face with four fasteners of a suitable size (suggested minimum
1/4" diameter, not supplied)
Construction:.074 ABS plastic/aluminum
3.0 SPECIFICATIONS
Camera Mounting:Slotted camera bracket
Enclosure
Positioning:Swivel mount allows enclosure
to be positioned 0–180° horizontally or vertically
Maximum
Camera/Lens Size:Accommodates camera/lens
combinations (including BNC
connector) up to:
2.75" W x 2.50" H x 5.00" L
Viewing Window:1/8" thick, optically clear, im-
pact resistant Lexan.
Viewing area 2-1/2" diameter
Finish:Housing: Textured black or
white
Mount:Powder coated black
or white
Dimensions:See Figure 1
Maximum Load:2 lbs (.9 kg)
Approximate
Weight:7.5 oz
Figure 1. Dimension Drawing
2Pelco Manual C439M (10/92)
4.0 INSTALLATION
Note:Fasteners to secure the enclosure to a load-
bearing solid surface are not supplied.
To install the camera/lens, perform the following:
1.Using the mount as a template, mark and drill
holes in the mounting surface. (If you are
planning to conceal the wiring through the
mounting surface you will also need to mark
and drill the cable feedthrough hole at this
time.) Attach the enclosure with integral mount
securely to the mounting surface with fasteners of a suitable size (1/4-20 screws recommended, not supplied).
2.Gently pull the front of the housing to separate
the two halves of the enclosure.
3.Place the camera/lens onto the slotted camera
bracket and secure with the 1/4-20 screw
provided.
4.Route the coax through the cable feedthrough
hole located on the rear of the enclosure.
(If desired, the coax can also be routed through
the feedthrough hole on the mount to conceal
the wiring through the mounting surface.)
5.If necessary, shim up the camera/lens using
flat washers (not provided) to ensure the camera/lens is in the center of the viewing window.
6.Adjust the camera/lens (front to back) so that
the lens is as close to the viewing window as
possible.
7.Replace front cover.
Pelco Manual C439M (10/92)3
5.0WARRANTY AND RETURN
INFORMATION
WARRANTY
PELCO will repair or replace, without charge, any
merchandise proved defective in material or workmanship for a period of one year after the date of shipment
(six months on all pan and tilts with auto scan and
medium duty scanners, and two years on Legacy®,
Intercept® and CM9500/CM8500 Matrix products).
PELCO will warranty all replacement parts and repairs
for 90 days from the date of shipment. All goods for
warranty work shall be sent freight prepaid to our
Clovis, California facility. Repairs made necessary by
reason of misuse, alteration, normal wear, or accident
are not covered under this warranty. PELCO is not
liable for any incidental or consequential expenses or
liability incurred by the customer as a result of field
repair, installation, or any other reason.
The above warranty is in lieu of any other expressed or
implied warranty, condition, or guarantee by PELCO
of the equipment listed herein. PELCO makes no
warranties except for intended use and will not be liable
for any loss, damage, or costs arising, whether consequential or incidental, from the use of said merchandise.
This warranty gives you specific legal rights. You may
also have additional rights, which are subject to variation from state to state.
RETURNS
In order to expedite parts returned to the factory for
repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authoriza-
tion number (CA number if returned for credit, and RA
number if returned for repair). Goods returned for
repair or credit should be clearly identified with the
assigned CA/RA number and freight should be prepaid. All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Ship freight prepaid to:PELCO
300 West Pontiac Way
Clovis, CA 93612-5699
®
PELCO
300 West Pontiac Way
Clovis, CA 93612-5699 USA
(559) 292-1981 • (800) 289-9100
FAX (800) 289-9150 or (559) 292-3827
DataFAX (800) 289-9108 or (559) 292-0435
If a warranty repair is required, contact PELCO at
(800) 289-9100 or (559) 292-1981 for a
International customers call 1-559-292-1981 or
FAX 1-559-348-1120
Repair Authorization number (RA), and provide the
following information:
(Product specifications subject to change
without notice.)
1.Model and serial number
2.Date of shipment, P.O. number, Sales Order
C439M
number, or PELCO invoice number
3.Details of the defect or problem
If there is a dispute regarding the warranty of a product
which does not fall under the warranty conditions
stated above, please include a written explanation with
the product when returned.
Ship freight prepaid to:PELCO
300 West Pontiac Way
Clovis, CA 93612-5699
Method of return shipment shall be the same as method
by which the repair item is received by PELCO.
4Pelco Manual C439M (10/92)
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.