Pelco FX82011SSTR-2, FX82011SSCR-2, FX82011MSTR-2, FX82011MSCR-2 Specsheet

PRODUCT SPECIFICATION

FX82011 Ethernet Media Converter

video transmission

ONE 10BASE-T/100BASE-TX PORT AND ONE 100BASE-FX FIBER PORT

Product Features

• Ethernet Media Converter:

– One 10Base-T/100Base-TX Port
– One 100Base-FX Port That Accepts Two Fibers

• Converts 10Base-T/100Base-TX Ethernet Data to 100Base-FX

Ethernet Data and Vice Versa

• Compatible with Third-Party 100Base-FX Ethernet Equipment

(Multimode ST and SC Models Only)

• Designed for Point-to-Point Applications

• User-Selectable 10Base-T/100Base-TX Port Functions:

– Autonegotiation Between 10 Mbps and 100 Mbps Data Rates and

Between Full-Duplex and Half-Duplex Modes
– 10 Mbps or 100 Mbps Selectable
– Full-Duplex or Half-Duplex Mode Selectable
– Enabling/Disabling of Flow Control

• Auto MDI/MDI-X (Medium Dependent Interface/Medium Dependent

Interface Crossover) Operation

• Link-Down Detection

• Compliant with IEEE 802.3, 802.3u, and 802.3x Standards

• Multimode Fiber Support for Distances up to 6 km

• Single-Mode Fiber Support for Distances up to 46 km

• Laser Diode for Transmission of Optical Signals

• Environmentally Hardened

• Designed to Meet NEMA TS 2 and Caltrans Traffic Signal Control

Equipment Environmental Standards

• No Performance Adjustments Required

• 12 VDC or 24 VAC Power Supply

• Stand-Alone and Rack-Mountable Modular Design

• LED Indicators for Monitoring of Optic Signal/Laser Status,

100Base-FX Port Status Including Far End Fault Indication (FEFI),
10Base-T/100Base-TX Port Status, and Operating Power

The

FX82011

Ethernet data to 100Base-FX Ethernet data and vice versa.

point-to-point applications, the

media converter converts 10Base-T/100Base-TX

Designed for

FX82011

media converter provides
one 10Base-T/100Base-TX port and one 100Base-FX fiber port. Two
fibers are required to transport bidirectional data over the
100Base-FX fiber port.

The 100Base-FX fiber port is automatically forced to full-duplex
100 Mbps operation. Networking functions for the 10Base-T/
100Base-TX port (RJ-45 twisted-pair copper port) are user-selectable
by means of a rotary switch. Autonegotiation allows the port to auto­matically negotiate between 10 Mbps and 100 Mbps data rates and
between full-duplex and half-duplex modes. If autonegotiation is not
desired, the port can be forced to specific modes of operation:
10 Mbps or 100 Mbps data rate, half-duplex or full-duplex mode, and
the enabling/disabling of flow control. The auto MDI/MDI-X feature
allows the RJ-45 port to connect to either a straight-through or cross­over RJ-45 cable.

C2625 / NEW 1-08

The link-down detection feature of the media converter propagates a
link-down status among all 10Base-T/100Base-TX and 100Base-FX
ports connected in the network when a 10Base-T/100Base-TX link or
100Base-FX link goes down. As a result, all ports are disabled and
data transmission halts until the faulty link is restored.

Modular in design, the

FX82011

unit can be rack mounted or can be
used as a stand-alone module. Rack mounting is accomplished using
the RK5000 Series rack mount chassis. As a stand-alone module, the
unit can be placed on a desktop or can be mounted to a wall.

ONE 10/100 Mbps

CONNECTION

FX82011

TWO

FIBERS

FX82011

International Standards

Organization Registered Firm;

ISO 9001 Quality System

ONE 10/100 Mbps

CONNECTION

TECHNICAL SPECIFICATIONS

MODELS

Fiber Optic

Model Number

Connector

Type

Number

of Fibers

Wavelength

(Transmit/Receive)

Multimode (62.5/125 µm)

FX82011MSTR-2 ST 2 1310/1310 nm 26 dB* 6 km (3.7 mi)

FX82011MSCR-2 SC 2 1310/1310 nm 26 dB* 6 km (3.7 mi)

Single-Mode (9/125 µm)

FX82011SSTR-2 ST 2 1310/1310 nm 28 dB 46 km (28.6 mi)

FX82011SSCR-2 SC 2 1310/1310 nm 28 dB 46 km (28.6 mi)

*When using 50/125 µm multimode fiber, subtract 3 dB from the optical power budget.

†

Maximum transmission distance is limited by fiber bandwidth.

‡

Maximum transmission distance is based on attenuation of 0.5 dB/km plus a 5 dB buffer for connector and
splice losses.

Notes:

• Single-mode FC connector is available upon request. Contact the factory for additional information.

• For conformal coated models, replace the first letter F in the model number with the letter C. The conformal
coated version of FX82011MSTR-2, for example, is CX82011MSTR-2.

• For models with higher optical power budgets, contact the factory.

Optical

Power

Budget

Maximum

Transmission

Distance Supplied Accessories

Regulated switching power supply with multiple

†

plug adapters (North American, Australian,
United Kingdom, and European); 100-240 VAC,

†

50-60 Hz input, 12 VDC output

Note:

In extreme temperature conditions, it is

‡

recommended that an industrial-rated outdoor

‡

power supply be used.

Wall clip for attachment of single module to wall

PERFORMANCE

Switch Type Unmanaged Layer 2
Switch Method Store and forward
Data Rate 10/100 Mbps
Compliance IEEE 802.3, 802.3u, 802.3x
Interface Auto MDI/MDI-X
Operating Mode Half-duplex or full-duplex
Address Table Size 1,024 MAC address entries with automatic

learning and aging

Quality of Service IEEE 802.1p priority, tag-based, 4 queues per

port, weighted fair queuing scheduling

Maximum Frame Size Untagged Ethernet frames up to 1,518 bytes

Tagged Ethernet frames up to 1,522 bytes

GENERAL

Operating Temperature -40° to 167°F (-40° to 75°C)
Input Power Requirements 12 VDC or 24 VAC, 0.50 A
LED Indicators Power

100Base-FX Port Status (link/activity, FEFI)
Optic Fault (optic signal/laser status)
10Base-T/100Base-TX Port Status

(link/activity and speed, duplex/collision
and speed)

Dimensions 8.75" D x 1.08" W x 4.81" H

(22.23 x 2.74 x 12.22 cm)
Unit Weight 1.6 lb (0.73 kg), approximate
Shipping Weight 3.0 lb (1.36 kg)

CERTIFICATIONS

• CE, Class A

• UL Listed

• UL Listed to Canadian safety standards

• FCC, Class A

• C-Tick

• Complies with FDA requirements for Class 1 laser products

• Designed to meet NEMA TS 2 and Caltrans traffic signal control
equipment standards for ambient operating temperature, mechanical
shock and vibration, humidity with condensation, high-line/low-line
voltage conditions, and transient voltage protection (certification pending)

Note:

Conformal coating is required for operation in environments with

relative humidity above 95% (condensing).

OPTIONAL ACCESSORIES

WM5001-3U Wall mount base kit for single-width module
WM5001-3UEXP Wall mount expansion kit for single-width

RK5000-3U 19-inch rack mount chassis for 14 slots,

RK5000PS-3U 19-inch rack mount chassis for 12 slots with

EPS5000-120 External rack power supply, 1 RU, dual 120 W

RK5001B-3U Blank filler panel, single width
RK5002B-3U Blank filler panel, double width
RK5001-1UEXP Adapter kit that allows a 3 RU double-width

module

no power (3 RUs)

power (3 RUs)

power outputs

fiber module to be used in RK5100PS-5U rack
mount chassis

MECHANICAL

Connectors

Rack Power/Alarm 1, 4-pin connector
Stand-Alone Power 1, 2-pin connector, screw terminal
Electrical 1, RJ-45, 10Base-T/100Base-TX
Fiber Optic 1, dual-fiber ST or SC

Pelco, Inc. Worldwide Headquarters:

3500 Pelco Way, Clovis, California 93612-5699 USA

USA & Canada
International
www.pelco.com

Tel: [phone] • FAX: [phone]

Tel: [phone] • FAX: [phone]

Pelco and the Pelco logo are registered trademarks of Pelco, Inc.

Product specifications and availability subject to change without notice.

©Copyright 2008, Pelco, Inc. All rights reserved.