Pelco FUMS-FFX8, FUMS-FFX4TX4, FUMS-FFX4, FUMS-FFX2TX2, FUMS-FTX8 User Manual

INSTALLATION AND OPERATION MANUAL

FUMS-F(FX,TX)(2,4,8)[TX(2,4)] Series

4- OR 8-PORT UNMANAGED ETHERNET SWITCHES

This manual serves the
following Model Numbers:

FUMS-FFX8

FUMS-FFX4TX4

FUMS-FTX8

FUMS-FFX4

FUMS-FFX2TX2

FUMS-FTX4

The Pelco Series of four and eight port unmanaged Ethernet switches are designed

to transmit and receive 10/100Mbps data over optical fiber through user selectable

FSFP options or 10/100Mbps data over CAT5E/6 electrical cable. These units

integrate eight independent 10/100Mbps channels in a single package.

The FUMS-FFX4TX4, FUMS-FFX2TX2, FUMS-FTX8 and FUMS-FTX4 require

the ordering of sold-separately interchangeable Pelco FSFP modules for fiber

type, distance and connectors.

All electrical interfaces will Auto-Negotiate to 10Mbps, or 100Mbps Ethernet

rate without any adjustments. The optical interfaces operate at a 100Mbps

Ethernet rate.

The models in this series are environmentally hardened to operate in

demanding environments.

LED indicators are provided for confirming equipment operating status.

These units are interchangeable between stand-alone or card mount

configurations. See Figure A on Page 10 for installation instructions.

See Figures 1 – 14 for complete installation details.

TECH SUPPORT: [phone] INTERNATIONAL: [phone]

C3927M-A / REV 07-28-14

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the points where they exit
from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has been dropped.

14. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases shall be placed on the
apparatus.

15. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

16. Installation should be done only by qualified personnel and conform to all local codes.

17. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must
not be installed where exposed to rain and moisture.

18. Use only installation methods and materials capable of supporting four times the maximum specified load.

19. Switch does not support Internet Group Management Protocol (IGMP) and should not be used as a core switch.

20. A CCC-approved power cord must be used to power this equipment when used in China.

21. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not
perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

TECH SUPPORT: [phone] INTERNATIONAL: [phone] C3927M-A / REV 07-28-14

INSTALLATION AND OPERATION MANUAL FUMS-F(FX,TX)(2,4,8)[TX(2,4)] SERIES

FIGURE 1 – FUMS-FFX4TX4

AND RJ-45

SELECTION OF FSFP MODULES

OPTICAL FIBERS DETERMINED BY

FIGURE 2 – FUMS-FFX4TX4

BLACK WITH WHITE STRIPES
BLACK
Power Supply:
Surface Mount: 8-15 VDC @ 2W
Rack Mount: From Rack

NOTE: Remove Electrical

Connector for Rack
Mount Units

RE AR PA NELFRONT PANEL

TECH SUPPORT: [phone] INTERNATIONAL: [phone]

C3927M-A / REV 07-28-14

INSTALLATION AND OPERATION MANUAL FUMS-F(FX,TX)(2,4,8)[TX(2,4)] SERIES

FIGURE 3 – FUMS-FFX8

SELECTION OF FSFP MODULES

OPTICAL FIBERS DETERMINED BY

BLACK WITH WHITE STRIPES
BLACK
Power Supply:
Surface Mount: 8-15 VDC @ 2W
Rack Mount: From Rack

FIGURE 4 – FUMS-FFX8

NOTE: Remove Electrical

Connector for Rack Mount
Units

RE AR PA NELFRONT PANEL

TECH SUPPORT: [phone] INTERNATIONAL: [phone] C3927M-A / REV 07-28-14

INSTALLATION AND OPERATION MANUAL FUMS-F(FX,TX)(2,4,8)[TX(2,4)] SERIES

FIGURE 5 – FUMS-FTX8

RJ-45

BLACK WITH WHITE STRIPES
BLACK
Power Supply:
Surface Mount: 8-15 VDC @ 2W
Rack Mount: From Rack

FIGURE 6 – FUMS-FTX8

NOTE: Remove Electrical

Connector for Rack Mount
Units

RE AR PA NELFRONT PANEL

TECH SUPPORT: [phone] INTERNATIONAL: [phone]

C3927M-A / REV 07-28-14

INSTALLATION AND OPERATION MANUAL FUMS-F(FX,TX)(2,4,8)[TX(2,4)] SERIES

FIGURE 7 – FUMS-FFX2TX2

SELECTION OF

OPTICAL FIBERS

FSFP MODULES

DETERMINED BY

RJ-45

BLACK WITH WHITE STRIPES
BLACK
Power Supply:
Surface Mount: 8-15 VDC @ 2W
Rack Mount: From Rack

FIGURE 8 – FUMS-FFX2TX2

NOTE: Remove Electrical

Connector for Rack
Mount Units

RE AR PA NELFRONT PANEL

TECH SUPPORT: [phone] INTERNATIONAL: [phone] C3927M-A / REV 07-28-14

INSTALLATION AND OPERATION MANUAL FUMS-F(FX,TX)(2,4,8)[TX(2,4)] SERIES

FIGURE 9 – FUMS-FFX4

SELECTION OF FSFP MODULES

OPTICAL FIBERS DETERMINED BY

BLACK WITH WHITE STRIPES
BLACK
Power Supply:
Surface Mount: 8-15 VDC @ 2W
Rack Mount: From Rack

FIGURE 10 – FUMS-FFX4

NOTE: Remove Electrical

Connector for Rack
Mount Units

RE AR PA NELFRONT PANEL

TECH SUPPORT: [phone] INTERNATIONAL: [phone]

C3927M-A / REV 07-28-14

INSTALLATION AND OPERATION MANUAL FUMS-F(FX,TX)(2,4,8)[TX(2,4)] SERIES

FIGURE 11 – FUMS-FTX4

RJ-45

BLACK WITH WHITE STRIPES
BLACK
Power Supply:
Surface Mount: 8-15 VDC @ 2W
Rack Mount: From Rack

FIGURE 12 – FUMS-FTX4

NOTE: Remove Electrical

Connector for Rack
Mount Units

RE AR PA NELFRONT PANEL

TECH SUPPORT: [phone] INTERNATIONAL: [phone] C3927M-A / REV 07-28-14

INSTALLATION AND OPERATION MANUAL FUMS-F(FX,TX)(2,4,8)[TX(2,4)] SERIES

FIGURE 13 – POSSIBLE ETHERNET CONFIGURATION

Ethernet IEEE 802.3 Network Element determined by user.

Optical Fiber

SC or LC

Connectors

SINGLE FIBER

FSFP MODULE

CAT5e/6 with

RJ45 Connections

Ethernet IEEE

802.3 Network
Element

FIGURE 14 – LED INDICATORS

ACTIVITY (SFP) RJ45 POWER
GREEN
YELLOW

OFF

Link/Activity Link/Activity Unit powered up

– Highest Data Rate

Unit Powered Down No Link/Activity Unit Powered Down

FUMS-FFX4TX4A FUMS-FFX4TX4B

–

Negotiated

CAT5e/6 with

RJ45 Connections

Ethernet IEEE

802.3 Network
Element

TECH SUPPORT: [phone] INTERNATIONAL: [phone]

C3927M-A / REV 07-28-14

MECHANICAL INSTALLATION INSTRUCTIONS FUMS-F(FX,TX)(2,4,8)[TX(2,4)] SERIES

13

11.9cm
[4.7in]

15cm

[5.9in]

7. 5cm
[2.9in]

0.63cm
[0.25in]

INSTALLATION CONSIDERATIONS

The FUMS-F models are supplied as Standalone/Rack modules.
Units should be installed in dry locations protected from extremes of
temperature and humidity.

CARD CAGE RACKS

CAUTION: Although the units are hot-swappable and may be installed

without turning power off to the rack, the manufacturer recommends
that the power supply be turned off and that the rack power supply
is disconnected from any power source. Note: Remove electrical
connector before installing in card cage rack.

1. Make sure that the card is oriented right side up, and slide it into the
card guides in the rack until the edge connector at the back of the
card seats in the corresponding slot in the rack’s connector panel.
Seating may require thumb pressure on the top and bottom of the
card’s front panel.

CAUTION: Take care not to press on any of the LEDs.

2. Tighten the two thumb screws on the card until the front panel of the
card is seated against the front of the rack.

WARNING: Unit is to be used with a Listed Class 2 power supply.

IMPORTANT SAFEGUARDS:

A) Elevated Operating Ambient - If installed in a closed or multi-

unit rack assembly, the operating ambient temperature of the
rack environment may be greater than room ambient. Therefore,
consideration should be given to installing the equipment in an
environment compatible with the maximum ambient temperature
(Tma) specified by the manufacturer.

FIGURE A

Dimensions are for standard one and two slot modules

.2cm

[5.2in]

11.9cm
[4.7in]

7. 5cm

0.63cm
[0.25in]

2.75cm
[1.1in]

5.5cm
[2.2in]

[2.9in]

15cm

[5.9in]

B) Reduced Air Flow - Installation of the equipment in a rack should be

such that the amount of air flow required for safe operation of the
equipment is not compromised.

TECH SUPPORT: [phone] INTERNATIONAL: [phone] C3927M-A / REV 07-28-14

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in
material or workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years:
– Fiber optic products
– Unshielded Twisted Pair (UTP) transmission products
– CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and

MC3651H-2X camera models

• Three years:
– FD Series and BU Series analog camera models
– Fixed network cameras and network dome cameras with Sarix
– Sarix thermal imaging products (TI and ESTI Series)
– Fixed analog camera models (C20 Series, CCC1390H Series, C10DN Series,

and C10CH Series)
– EH1500 Series enclosures
– Spectra
– Spectra HD dome products
– Camclosure

®

IV products (including Spectra IV IP)

®

IS Series integrated camera systems

– DX Series video recorders (except DX9000 Series which is covered for a

period of one year), DVR5100 Series digital video recorders, Digital Sentry

Series hardware products, DVX Series digital video recorders, and NVR300

Series network video recorders

®

– Endura
– Genex

Series distributed network-based video products

®

Series products (multiplexers, server, and keyboard)
– PMCL200/300/400 Series LCD monitors
– PMCL5xxF Series and PMCL5xxNB Series LCD monitors
– PMCL5xxxBL Series LED monitors

• Two years:
– Standard varifocal, fixed focal, and motorized zoom lenses
– DF5/DF8 Series fixed dome products

®

– Legacy
– Spectra III

Series integrated positioning systems

™

, Spectra Mini, Spectra Mini IP, Esprit®, ExSite®, ExSite IP, and

PS20 scanners, including when used in continuous motion applications
– Esprit Ti and TI2500 Series thermal imaging products
– Esprit and WW5700 Series window wiper (excluding wiper blades)
– CM6700/CM6800/CM9700 Series matrix
– Digital Light Processing (DLP

®

) displays (except lamp and color wheel). The
lamp and color wheel will be covered for a period of 90 days. The air filter is
not covered under warranty.

®

technology

• Six months:
– All pan and tilts, scanners, or preset lenses used in continuous motion

applications (preset scan, tour, and auto scan modes)

Pelco will warrant all replacement parts and repairs for 90 days from the date of
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid
to a Pelco designated location. Repairs made necessary by reason of misuse,
alteration, normal wear, or accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss
resulting from the specific use or application made of the Products. Pelco’s liability
for any claim, whether based on breach of contract, negligence, infringement of
any rights of any party or product liability, relating to the Products shall not exceed
the price paid by the Dealer to Pelco for such Products. In no event will Pelco be
liable for any special, incidental, or consequential damages (including loss of use,
loss of profit, and claims of third parties) however caused, whether by the
negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may
also have additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or
[phone] to obtain a Repair Authorization number (RA), and provide the

®

following information:

1. Model and serial number

2. Date of shipment, P.O. number, sales order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product that does not fall under
the warranty conditions stated above, please include a written explanation with
the product when returned.

Method of return shipment shall be the same or equal to the method by which the
item was received by Pelco.

RETURNS

To expedite parts returned for repair or credit, please call Pelco at [phone]
or [phone] to obtain an authorization number (CA number if returned for
credit, and RA number if returned for repair) and designated return location.

All merchandise returned for credit may be subject to a 20 percent restocking and
refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned
CA or RA number and freight should be prepaid.

Revised 10-9-12

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.

Pelco, the Pelco logo, and other trademarks associa ted with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates. © Copyright 2013, Pelco, Inc.
ONVIF and the ONVIF logo are trademarks of ONVIF Inc. All other product names and services are the property of their respective companies. All rights reserved.
Product specifications and availability are subject to change without notice.

Pelco by Schneider Electric 3500 Pelco Way Clovis, California 93612-5699 United States

USA & Canada Tel [phone] Fax [phone]

International Tel [phone] Fax [phone]

www.pelco.com www.pelco.com/community