Pelco FSV10D1S1ST, FSV10D1S1FC Specsheet

PRODUCT SPECIFICATION

transmission & power

FSV10D1 Fiber Transmitter

SINGLE-CHANNEL DIGITALLY ENCODED VIDEO WITH BIDIRECTIONAL DATA

Product Features

• Designed for Use in Spectra® IV Domes

• 10-Bit Digitally Encoded Video for High-Quality Video Transmission

over a Single Fiber

• Bidirectional RS-422 Data Channel or Coaxitron

• Supports Pelco Coaxitron “Up-the-Coax” Control Signals for a

Distance up to 69 km (43 mi)

• Multimode Fiber Support for Distances up to 4 km (2.5 mi)

• Single-Mode Fiber Support for Distances up to 60 km (37 mi)

• Exceeds All Requirements for the RS-250C Medium-Haul

Transmission Specification

• Laser Diode for Transmission of Optical Signals

• Compatible with NTSC, PAL, and SECAM Video Standards

• Designed to Meet NEMA TS-1/TS-2 and Caltrans Traffic Signal

Control Equipment Environmental Standards

• LED Status Indicators for Monitoring All Critical Operating

Parameters

®

Communication

The FSV10D1 fiber transmitter is designed for quick and easy
installation into the back box of Spectra

®

IV domes. The FSV10D1

transmitter allows transmission of one unidirectional composite
video channel and one bidirectional RS-422 data channel over one
optical fiber. In addition, the “up-the-coax” technology allows
Coaxitron

®

pan/tilt/zoom (PTZ) control data to be transmitted the full

distance of the fiber. Available in multimode and single-mode
versions, the FSV10D1 transmitter is compatible with the FRV10D1
receiver.

The FSV10D1 transmitter allows the user to choose bidirectional
data or up-the-coax through use of a dip switch on the compatible
FRV10D1 receiver unit. The selection of RS-422 data communication
allows PTZ control of the Spectra IV dome. With Coaxitron control,
PTZ control signals are transmitted over video coaxial cable from the
controller to the FRV10D1 receiver. The receiver then transmits the
Coaxitron data onto the fiber to the FSV10D1 transmitter. The
Coaxitron data is transmitted from the controller to the Spectra IV
dome during the vertical blanking interval of the video signal.

The FSV10D1 transmitter includes a corresponding 13-inch fiber
cable for easier pre-wiring installation. The unit operates using
power supplied from the Spectra IV dome.

International Standards

Organization Registered Firm;

ISO 9001 Quality System

C3921 / NEW 11-1-12

TECHNICAL SPECIFICATIONS

MODELS

Transmitter

FSV10D1M1ST FRV10D1M1ST ST 1 1310/1550 nm 16 dB 4 km (2.5 mi)

FSV10D1S1ST FRV10D1S1ST ST

FSV10D1S1FC FRV10D1S1FC FC

Note: This product requires a fiber installation with a minimum 30 dB connector return loss.

Compatible

Receiver

Fiber Optical

Connector Type

Number

of Fibers

Multimode (62.5/125 µm)

Single Mode (9/125 µm)

1 1310/1550 nm 20 dB 60 km (37 mi)

1 1310/1550 nm 20 dB 60 km (37 mi)

Wavelength

Optical Power

Budget

Maximum

Transmission

Distance

VIDEO

Video Input 1.0 Vp-p, 75 ohms
Overload >1.5 Vp-p
Bandwidth 5 Hz to 6.5 MHz
Differential Gain <2%
Differential Phase <0.7°
Tilt <1%
Signal-to-Noise Ratio 67 dB at maximum optical loss budget
Max. Coaxial Cable (RG59) 100 m (300 ft) camera to fiber optic module to

maintain 6 Mhz bandwidth

DATA

Interface RS-422
Rate DC-115 Kbps (NRZ)

ELECTRICAL

Wavelength 1310/1550 nm, multimode and single-mode
Number of Fibers 1
Optical Emitter Laser diode
LED Indicators Link
Connectors

Optical ST or FC

Power 8 to 15 VDC at 350 mA from dome

GENERAL

Dimensions 10.16 × 6.4 cm

(4.0" L × 2.5" W)
MTBF >100,000 hours
Operating Temperature –40° to 75°C (–40° to 167°F)
Storage Temperature –40° to 85°C (–40° to 185°F)
Relative Humidity 0% to 95%, noncondensing
Unit Weight 0.210 kg (0.460 lb)
Shipping Weight 0.225 kg (0.500 lb)

CERTIFICATIONS/RATINGS

• CE, Class A

• FCC, Class A

• UL/cUL Listed

•C-Tick

• Designed to meet NEMA TS 1/TS 2 and Caltrans traffic signal control

equipment environmental standards

Pelco by Schneider Electric

3500 Pelco Way, Clovis, California 93612-5699 United States

USA & Canada Tel [phone] Fax [phone]
International Tel [phone] Fax [phone]
www.pelco.com www.pelco.com/community

Pelco, the Pelco logo, and other trademark s associated with Pelco products referred

to in this publication are trademarks of Pelco, Inc. or its affiliates. ONVIF and the

ONVIF logo are trademarks of ONVIF Inc. All other product names and

Product specifications and availability are subject t o change without notice.

services are the property of their respective companies.

©Copyright 2012, Pelco, Inc. All righ ts reserved.