Pelco FRV80S1ST, FRV80M1ST, FRV80S1FC Specsheet

PRODUCT SPECIFICATION

transmission & power

FTV80/FRV80 Fiber Transmitter and Receiver

8-CHANNEL DIGITALLY ENCODED VIDEO

Product Features

• 10-Bit Digitally Encoded Video for High-Quality Multichannel Video

Transmission over a Single Fiber

• Multimode Fiber Support for Distances up to 3 km (1.9 mi)

• Single-Mode Fiber Support for Distances up to 48 km (29.8 mi)

• Exceeds All Requirements for EIA RS-250C Short-Haul

Transmission Specifications

• Compatible with NTSC, PAL, or SECAM Video Standards

• Designed to Meet NEMA TS 1/TS 2 and Caltrans Traffic Signal

Control Equipment Environmental Standards

• Laser Diode for Transmission of Optical Signals

• Voltage Transient Protection on All Power and Signal

Input/Output Lines

• LED Status Indicators for Monitoring All Critical

Operating Parameters

• Stand-Alone or Rack-Mountable Modular Design

The FTV80/FRV80 fiber transmitter and receiver transmit eight channels of video over one optical fiber in a two-slot wide design. The FTV80 transmitter and FRV80 receiver are available in multimode and single-mode versions.

FRV80M1ST

The FTV80/FRV80 plug-and-play design ensures ease of installation by requiring no electrical or optical adjustments. Modular in design, FTV80 and FRV80 units can be rack-mounted using the EURACK/USRACK chassis, or stand-alone modules can be placed on a desktop or mounted to a wall (wall mount kit not required).

For stand-alone and wall mount installations, external power is required for the FTV80/FRV80 units. The units can be powered with the recommended FEXTPS fiber external power supply.

International Standards

Organization Registered Firm;

ISO 9001 Quality System

C3919 / REVISED 12-11-12

TECHNICAL SPECIFICATIONS

MODELS

Transmitter

FTV80M1ST FRV80M1ST ST 1 1310 nm 16 dB 3 km (1.9 mi)

FTV80S1ST FRV80S1ST ST 1 1310 nm 16 dB 48 km (29.8 mi)

FTV80S1FC FRV80S1FC FC 1 1310 nm 16 dB 48 km (29.8 mi)

Note: This product requires a fiber installation with a minimum 30 dB connector return loss.

*Distance may be limited by optical dispersion. High bandwidth 50/125 µm fiber is required to achieve maximum

multimode distance. Contact Pelco Product Support before using these units for distances greater than 2 km (1.2 mi).

Compatible

Receiver

Fiber Optical

Connector Type

Multimode (62.5/125 µm)

Single Mode (9/125 µm)

Number

of Fibers

Wavelength

Optical Power

Budget

Maximum

Transmission

Distance*

VIDEO

Number of Channels 8 Video Input (FTV80/

Video Output (FRV80) 1.0 Vp-p, 75 ohms; NTSC, PAL, SECAM Overload >1.5 Vp-p Bandwidth (minimum) 10 to 6.5 MHz Differential Gain <2% Differential Phase <0.7° Tilt <1% Signal-to-Noise Ratio 67 dB typical Max. Coaxial Cable (RG59) 100 m (300 ft) camera to fiber optic module to

maintain 6 Mhz bandwidth

ELECTRICAL

Power

Surface Mount 8 to 15 VDC at 4 W

Rack Mount Provided by rack MTBF >100,000 hours Current Protection Automatic resettable solid-state current

limiters Circuit Board Meets IPC standards LED Indicators Video Sync, Power

MECHANICAL

Connectors

Power Terminal block Optical ST or FC Video BNC (gold-plated center pin)

Number of Rack Slots 2

GENERAL

Dimensions 15.5 × 13.5 × 5.6 cm

(6.1" D × 5.3" W × 2.2" H) Operating Temperature –40° to 75°C (–40° to 167°F) Storage Temperature –40° to 85°C (–40° to 185°F) Relative Humidity 0 to 95%, noncondensing Unit Weight 0.7 kg (1.5 lb) Shipping Weight 0.9 kg (2.0 lb)

CERTIFICATIONS/RATINGS

• CE, Class A

• FCC, Class A

• UL/cUL Listed

•C-Tick

• Designed to meet NEMA TS 1/TS 2 and Caltrans traffic signal control

equipment environmental standards

RECOMMENDED ACCESSORIES

EURACK 4 RU rack accessory with European power

supply USRACK 4 RU rack accessory with North American

power supply FEXTPS Fiber External Power Supply with multiple

plug adaptors (North American, Australian,

United Kingdom, and European);

100 to 240 VAC, 50 to 60 Hz input,

9 VDC output

Pelco by Schneider Electric

3500 Pelco Way, Clovis, California 93612-5699 United States

USA & Canada Tel (800) 289-9100 Fax (800) 289-9150 International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120 www.pelco.com

Pelco, the Pelco logo, and other trademarks associat ed with Pelco products referred

to in this publication are trademarks of Pelco, Inc. o r its affiliates. ONVIF and the

ONVIF logo are trademarks of ONVIF Inc. All othe r product names and

Product specifications and availability are subject to change without notice.

services are the property of their respective companies.