Pelco EC-4BY1SWUPOE-W, EC-4BY1SWCPOE-W Specsheet

PRODUCT SPECIFICATION

EC-4BY1SWCPOE-W EC-4BY1SWUPOE-W

transmission and power

EC-4BY1SWC/U Series EthernetConnect™ Switch

4-PORT, SELF-MANAGED, POE+ SWITCH WITH EXTENDED UPLINK

Product Features

• No Programming Required

• 10/100 Mbps Ethernet

– 4 x 10/100BASE-T/TX Electrical Ports Supporting PoE+

– 1 x 100 Mbps Extended Electrical Uplink

• Transmits Four Individual Ethernet Data Channels Over Standard

Cat5/Cat5e/Cat6 UTP Cable or Over Coaxial Cable

• Extends Ethernet up to 914 m (3,000 ft) at 10 Mbps or

610 m (2,000 ft) at 100 Mbps Over Cat5/Cat5e/Cat6 UTP Cable

• Extends Ethernet up to 1,524 m (5,000 ft) at 10 Mbps or

610 m (2,000 ft) at 100 Mbps Over Coaxial Cable

• Extended Temperature Operation of –40°C to 75°C (–40° to 167°F)

• 30 W PoE Capability on Ethernet Ports

• Electrical Ports Support Autonegotiation for 10 Mbps or 100 Mbps,

Full-Duplex or Half-Duplex Data

• Pre-Programmed Port for Uplink

• Full 10/100 Mbps Bandwidth

• Supports Multicast and Unicast

• Automatic MDI/MDI-X Crossover

• Designed to Meet Full Compliance with the Environmental

Requirements (Ambient Operating Temperature, Mechanical Shock,
Vibration, Humidity with Condensation, High-Line/Low-Line Voltage
Conditions and Transient Voltage Protection) of NEMA TS-1/TS-2 and
the Caltrans Specification for Traffic Signal Control Equipment

• Voltage Transient Protection on all Power and Signal Input/Output

Lines Provides Protection from Power Surges and Other Voltage
Transient Events

• Power and Activity Status LED Indicators

• Hot-Swappable Rack Modules

• Interchangeable Between Stand-Alone or Rack Mount Use

• IEEE802.3at Compliant

• Designed and Manufactured in the USA

The EthernetConnect™ EC-4BY1SWC/U Series has two models
that provide different front panel connectors; the C model for coaxial
applications and the U model for UTP applications.

The EthernetConnect EC-4BY1SWC/U Series is an Ethernet switch
with uplink management functionality that operates on the Ethernet
over copper (EoC). It provides four ports operating at 10/100 Mbps
and is designed to combine these four electrical ports into a single
electrical extended port that forwards the data to the next network
device. The switch does not require programming prior to use.

The EC-4BY1SWC/U Series comes pre-programmed, preventing
network video flooding with DIP switch selection of the extended
distance port as uplink. Ports 1 through 4 can supply up to 30 W of
Power over Ethernet (PoE) and incorporate PoE+ features based on
the IEEE802.3at standard. Front panel LED indicators confirm the
operating status of the Ethernet switch.

The EC-4BY1SWC/U Series can be either wall-mounted or
chassis-mounted for rack installation. All application configurations
should be verified at time of ordering to facilitate ease of
installation.

International Standards

Organization Registered Firm;

ISO 9001 Quality System

C3978 / NEW 3-10-14

TECHNICAL SPECIFICATIONS

Pelco, the Pelco logo, and other trad emarks associated with Pelco products referred

to in this publication are trademarks of Pelco, Inc. or its affiliates. ONVIF and the

ONVIF logo are trademarks of ONVIF Inc. All othe r product names and

services are the property of their respective comp anies.

Product specifications and availability are subject to change without no tice.

©Copyright 2014, Pelco, Inc. All rights reserved.

IMPORTANT NOTE. PLEASE READ. The network implementations are shown as general representations only and are not intended to show detailed network topologies. Your actual network will
differ, requiring changes or perhaps additional network equipment to accommodate the systems as illustrated. Please contact your local Pelco representative to discuss your specific requirements.

MODELS

EC-4BY1SWCPOE-W EthernetConnect 4-port coaxial self-managed

EC-4BY1SWUPOE-W EthernetConnect 4-port UTP self-managed

PoE switch, 30 W per port, EoC using coaxial
cable, extended uplink, wall mount

PoE switch, 30 W per port, EoC using Cat5/
Cat5e/Cat6 UTP, extended uplink, wall mount

ELECTRICAL

Operating Voltage

Non PoE 12 VDC (9 VDC

PoE 48 VDC
Power Consumption 10 W; PSE source power up to 120 W
Current Protection Automatic resettable solid-state current limiters
MTBF >100,000 hours
LED Indicators Data Link/Data Activity;

Power;
Power over Ethernet (PoE+)

†

when in USRACK or EURACK)

DATA

Data Interface Ethernet
Data Rate 10/100 Mbps;

Standards

POE+ IEEE802.3af/at

RFC 768 UDP, 2068 HTTP, 793 TCP, 791 IP,

Maximum Transmission Distances

Media COAX-RG59/U UTP, 1 Pair

Extended Port

Data Rate

Extended
Distance*

*Distance figures are obtained using in-house testing mirroring installations.

Factors such as coaxial and copper cable quality, the number of connectors
and splices in the cable run, the use of PoE, and environmental conditions
encountered within the installation might affect the actual transmission
distance and should be taken into consideration.

IEEE802.3 compliant;
Ethernet ports: Full/half-duplex;
Uplink port: Full-duplex

1783 TFTP, 894 IP over Ethernet

10 Mbps 100 Mbps 10 Mbps 100 Mbps

1,524 m

(5,000 ft)

610 m

(2,000 ft)

914 m

(3,000 ft)

610 m

(2,000 ft)

GENERAL

Dimensions 15.5 x 13.5 x 2.8 cm

Operating Temperature –40° to 75°C (–40° to 167°F)
Storage Temperature –40° to 80°C (–40° to 176°F)
Relative Humidity 0% to 95%, noncondensing
Unit Weight <0.45 kg (1 lb)
Shipping Weight <0.9 kg (2 lb)

(6.1" D x 5.3" W x 1.1" H)

MECHANICAL

Connectors

Power Terminal block
Coaxial Female BNC
UTP RJ-45
Data RJ-45

Surface Mount Wall or flat surface screw attachment

CERTIFICATIONS/RATINGS

• CE, Class A

• FCC, Part 15, Class A

• UL/cUL Listed

•C-Tick

• Designed to meet NEMA TS-1/TS-2 and the Caltrans traffic signal control
equipment environmental standards

RECOMMENDED ACCESSORIES

ECPS-12VDC-3A

ECPS-48VDC-5A

USRACK

EURACK

RACK1B Single-width blank module for empty rack slots

†

Contact Pelco pre-sales support, or refer to the appropriate installation and
operation manual when configuring and specifying power for a deployment.

†

†

†

†

EthernetConnect 12 VDC, 3 A power supply
for non-PoE pass-through mode applications

EthernetConnect 48 VDC, 5 A DIN-rail mount
power supply for PoE applications

Rack-mount chassis, 14-slot, 9 VDC, 6.5 A,
internal power supply, US power cord

Rack-mount chassis, 14-slot, 9 VDC, 6.5 A,
internal power supply, EU power cord

TYPICAL APPLICATIONS

Note: Coaxial applications use the EC-4BY1SWCPOE-W and EC-1501C-M; UTP applications use the EC-4BY1SWUPOE-W and EC-1501U-M.

Pelco by Schneider Electric

3500 Pelco Way, Clovis, California 93612-5699 United States

USA & Canada Tel [phone] Fax [phone]
International Tel [phone] Fax [phone]
www.pelco.com www.pelco.com/community