Pelco EC-1501U-M,EC-1501C-M,EC-1504U-W,EC-1504C-W,EC-1508UL-R,EC-1508CL-R,EC-1516UL-R,EC-1516CL-R specification sheets

PRODUCT SPECIFICATION

transmission and power

EC-1500C/U Series EthernetConnect™ Extender

1, 4, 8, OR 16 PORTS WITH PASS-THROUGH POE TO 15 WATTS, LOCAL OR REMOTE

Product Features

• Transmits Individual Ethernet Data Channels with Pass-Through

Power over Ethernet (PoE) over Standard Cat5/Cat5e/Cat6 UTP Cable
or Coaxial Cable

• Extends Ethernet up to 914 m (3,000 ft) at 10 Mbps or

m (2,000 feet) at 100 Mbps over Cat5/Cat5e/Cat6 UTP Cable

610

• Extends Ethernet up to 1,524 m (5,000

549 m (1,800 ft) at 100 Mbps over Coaxial Cable

• Extended Temperature Operation from

• Extended Pass-Through PoE Meets the IEEE802.3af Standard for

Power over Ethernet

• Full 10/100 Mbps Ban

• Supports Multicast, Unicast, and Jumbo Frame

• Symmetric Bandwidth Provides C

with Virtually Zero Packet Loss over the Total Usable Distance

• Type Tested to RFC-2544 TCP/IP Network Bandwidth Packet

Transmission Standards

• User-Selec

Transmission Distan

• Complies with all Major IEEE Standards and RFC Ne

for UDP, TCP/IP, and HTTP/HTTPs

table Data Rate for Maximum Bandwidth and

dwidth

ce Utilization

ft) at 10 Mbps or

–40° to 75°C (–40° to 167°F)

onsistent Upload and Downloa

twork Protocols

• Tested and Certified by an Independent Laboratory for Full

d

Compliance with the Environmental Requirements
Operating Temperature, Mechanical Shock, Vibration, Humidity with
Condensation, High-Line/Low-Line Voltage Conditions, and Transient
Voltage Protection) of NEMA TS-1/TS-2 and the Caltrans
Specification for Traffic Signal Control Equipment

• LED Status Indicators C

vailable in Small Unit Size, Interchangeable Stand-Alone, o

• A

Rack-Mounted Models

• Designed and Manufactured in the USA

onfirm Operating Status

(Ambient

r 1 RU

The EC-1500C Series is ideally suited for applications where the
existing coaxial cable needs to be leveraged for transmission of IP
signals. For UTP applications, the EC-1500U Series is an effective
Cat5/Cat5e/Cat6 UTP extender device beyond the 100 m (328 ft) limit
of traditional Ethernet. In addition, for system configurations that
have a single cable connected to the camera, the EC-1500C/U Series
can pass through PoE (up to 15 W) to the camera. Designed to be a
cost-effective, general-use product, the EC-1500C/U Series provides
maximum flexibility in these applications without any programming.

™

The EthernetConnect
Ethernet over copper (EoC). The EC-1500C Series extends up to
16 ports of 10/100 Mbps Ethernet with pass-through PoE over coaxial
cable. The EC-1500U Series extends up to 16 ports of 10/100 Mbps
Ethernet with pass-through PoE over twisted pair Cat5/Cat5e/Cat6
UTP cable. Single-channel units can be powered from a PoE source,
allowing for an installed network where power is not readily
available.

EC-1500C/U Series is used to extend

The EC-1500C/U Series units provide the ultimate flexibility for
extending a powered device (PD) over long distance copper. DIP
switches are provided for the user to select local or remote settings.
All application configurations should be verified at the time of
ordering to facilitate ease of installation.

C3976 / REVISED 3-14-17

TECHNICAL SPECIFICATIONS

IMPORTANT NOTE. PLEASE READ. The network implementations are shown as general representations only and are not intended to show

detailed network topologies. Your actual network will differ, requiring changes or perhaps additional network equipment to accommodate the
systems as illustrated. Please contact your local Pelco representative to discuss your specific requirements.

TYPICAL APPLICATIONS

Note: Coaxial applications use EC-1500C modules; UTP applications use EC-1500U modules.

PoE PASS-THROUGH MODE

NON-PoE MODE

MULTICHANNEL PoE APPLICATION

MULTICHANNEL NON-PoE APPLICATION