Pelco EA4348 User Manual

C279M-A (1/03) EA4348

Mount Adapter

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should be done only by qualified service personnel and conform to all local codes.

2. Installation shall be done in accordance with all local and national electrical and mechanical codes utilizing only approved materials.

3. Use only installation methods and materials capable of supporting four times the maximum specified load.

4. Use stainless steel hardware to fasten the mount to outdoor surfaces.

DESCRIPTION

The EA4348 is designed to allow the Esprit® Wall Mount (EWM) to mount to PP4348 and PP300L/PP301L parapet adapters or to adapt existing Legacy® style mounts for use with Esprit systems.

The EA4348 is compatible with the following Pelco adapters:

CM400 Corner adapter PA402 Pole adapter PP300L, PP301L Parapet corner adapters PP400 Parapet wall adapter PP4348 Parapet rooftop adapter

INSTALLATION

1. If installed, remove the Spectra/Legacy mount from the Spectra/Legacy adapter.

2. Attach the EA4348 adapter to the Legacy/Spectra adapter with the flat washers, split lock washers, and nuts that are provided. Refer to Figure 1, which shows the EA4348 adapter and the PA402 pole adapter.

3. Place the EWM mount over the studs on the EA4348 adapter.

4. Fasten the EWM mount to the EA4348 adapter with the flat washers, split lock washers, and nuts that are provided.

PA402

EA4348

Figure 1. Attaching EA4348 Adapter

Pelco World Headquarters • 3500 Pelco Way • Clovis, California 93612 USA • www.pelco.com

USA & Canada • Tel: 800/289-9100 • Fax: 800/289-9150

International • Tel: 1-559/292-1981 • Fax: 1-559/348-1120

SPECIFICATIONS

Adapter Mounting: Four holes for attaching EA4348 adapter to Legacy adapter; four 1.5-inch studs for attaching EWM mount to EA4348 adapter Construction: Aluminum Dimensions: 6.1 (W) x 9.7 (H) inches (15.5 x 24.6 cm) Weight: 1.20 lb (0.54 kg) Finish: Gray polyester powder coat

WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below:

• Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and MC3500/MC3600 Series); two years on all other cameras.

• Three years on Genex® Series (multiplexers, server, and keyboard) and 090 Series Camclosure Camera System.

•Two years on 100/150, 200 and 300 Series Camclosure® Camera Systems.

•Two years on cameras and all standard motorized or fixed focal length lenses.

•Two years on Legacy®, CM6700/CM6800/CM6800E/CM8500/CM9500/CM9740/CM9760 Matrix, DF5 and DF8 Series Fixed Dome products.

•Two years on Spectra®, Esprit®, and PS20 Scanners, including when used in continuous motion applications.

•Two years on Esprit and WW5700 series window wiper (excluding wiper blades).

• Eighteen months on DX Series digital video recorders.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico:

Service Department Pelco 3500 Pelco Way Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico:

Intermediate Consignee Ultimate Consignee

American Overseas Air Freight Pelco 320 Beach Road 3500 Pelco Way Burlingame, CA 94010 Clovis, CA 93612-5699 USA USA

REVISION HISTORY

Manual # Date Comments

C279M 3/02 Original version. C279M-A 1/03 Revised illustration and updated manual format.