Pelco EA2010 Specsheet
PRODUCT SPECIFICATION
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS;
ALL OTHERS ARE INCHES.
1.75
(4.45)
5.50
(13.97)
GAIN
EA2010 EQUALIZING AMPLIFIER
12 VAC
OUTPUT
8.80
(22.35)
LF BOOST
INPUT
HF BOOST
EA2010 Video Amplifier
POST-EQUALIZING, VIDEO ONLY
Product Features
• Solid-State Circuitry
• 120 or 230 VAC Input (for Wall Transformer)
• For Post-Equalization Applications Only
• Desktop or Rack Mount
The EA2010 provides a low cost, highly effective means of
maintaining picture quality in runs of up to 3,000 feet (914 m) of
RG59/U coaxial cable (equally effective with other cable types).
Front panel controls provide for adjustable overall amplifier flat gain
of 1 to 8 dB, plus adjustable high frequency boost of 0 to 18 dB at
12 MHz, maintaining full video amplitude, contrast, and detail.
communication & power
The EA2010 features all solid-state circuitry and is supplied with a
U.L. Listed wall transformer. Applications of the EA2010 should be
for post-equalization only (located near the monitoring equipment);
use as a pre-equalizer is discouraged.
The EA2010 is a desktop unit. Up to three units can be mounted in a
single 1.75-inch x 19-inch (4.44 cm x 48.26 cm) rack by using the
R300 rack mount kit, or two units can be mounted side-by-side in
one chassis using the DT200 dual desktop mount kit.
C630 / REVISED 10-00
International Standards
Organization Registered Firm;
ISO 9001 Quality System
TECHNICAL SPECIFICATIONS
TYPICAL CONFIGURATION
MODELS
EA2010 Desktop post-equalizing video amplifier, 120
VAC operation
EA2010/220 Same as EA2010 except 230 VAC operation
ELECTRICAL
Input Voltage 120 VAC, 50/60 Hz or 230 VAC, 50 Hz
Power Requirements
for Transformer 1.5 VA (.125 amp) at 12 volts RMS ±15%,
50/60 Hz from a dedicated, isolated power
source
Inputs Single BNC, internally terminated in 75 ohms
Outputs Single BNC, source terminated
Gain Adjustable from 1 to +8 dB
Signal-to-Noise Ratio -74 dB
Frequency
Response Adjustable from flat (±1 dB) at 12 MHz, to
greater than 18 dB of boost at 12 MHz
Output
Dynamic Range Up to 2 Vp-p at 50% APL
Up to 1.5 Vp-p at 90% APL
Cable Lengths Maximum
Cable Type Effective Distance
RG59/U 3,000 ft (914.4 m)
RG6/U 4,500 ft (1371.6 m)
RG11/U 6,000 ft (1828.8 m)
RG15/U 8,000 ft (2438.4 m)
MECHANICAL
Recessed Screwdriver
Adjustments Gain, HF boost, LF boost
CERTIFICATIONS/RATINGS
• CE, Class B (EA2010/220)
• UL Listed (EA2010)
• FCC, Class B (EA2010)
• Meets NEMA Type 1 standards
OPTIONAL ACCESSORIES
DT200 Dual desktop mount kit; two units can be
mounted side-by-side in one desktop chassis.
R300 Rack mounting kit (1 RU) for up to three
modules. Blank filler panels provided for less
than three modules. (Factory racking available
for R300 rack kit only. Specify when ordering.)
GENERAL
Construction
Cover Steel, black polyester powder coat
Chassis Steel, zinc plated
Panel Aluminum, black polyester powder coat with
Environment 32° to 120°F (0° to 49°C)
Unit Weight 3 lb (1.35 kg)
Shipping Weight 4 lb (1.8 kg)
white silk-screen
0% to 90% relative humidity
Pelco Worldwide Headquarters:
3500 Pelco Way, Clovis, California 93612-5699 USA
USA & Canada Tel: (800) 289-9100 • FAX (800) 289-9150
International Tel: (559) 292-1981 • FAX (559) 348-1120
www.pelco.com
Pelco and the Pelco logo are registered trademarks of Pelco.
Specifications subject to change without notice.
©Copyright 2000, Pelco. All rights reserved.
Loading...