Pelco E700A User Manual

C2414M-A (3/00) E700A Air Funnel Kit
®
3500 Pelco Way Clovis, CA 93612-5699 USA
In North America & Canada: Tel (800) 289-9100 FAX (800) 289-9150
International Customers: Tel +1 (559) 292-1981 FAX +1 (559) 348-1120
www.pelco.com
DESCRIPTION
The E700A Air Funnel Kit provides positive pressure airflow across the face of the front window of the E700 Series, HT10V Series, and MT10P Enclosures to remove and prevent dust accumulation.
The air funnel kit contains the following parts:
1 Air funnel 1 Neoprene gasket, used on enclosures E706-16 and E706-24 4 Screws, used on enclosure E708-24 4Washers, used on enclosure E708-24
E706-16 and E706-24 Enclosure
1. Release the latches on the front cover of the enclosure.
2. Do not remove the front window and ring.
3. Place neoprene gasket on the window and trim to fit around window perimeter.
4. Position the E700A Air Funnel against the gasket on top of the window.
5. Fasten the two latches.
6. Connect the E700A to a filtered compressed air supply with a minimum of 35 psi at 30 cfm.
FRONT COVER
(WINDOW & RING)
LATCH
GASKET
AIR FUNNEL
Figure 1. E700A Installation (E706-16/-24 Shown)
HT10V, HT10V/RC, and MT10P Enclosures
1. Remove four bolts from the front of the enclosure. Refer to item A , Figure 2.
2. Position the E700A over the window of the enclosure and secure with the bolts and washers supplied with the air funnel kit. Refer to item B , Figure 2.
3. Connect the E700A to a filtered compressed air supply with a minimum of 35 psi at 30 cfm.
Figure 2. E700A Installation for HT10V, HT10V/RC, and MT10P Enclosures.
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:
• Five years on FT/FR8000 Series fiber optic products.
• Three years on Genex
• Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a five-year warranty.
•Two years on standard motorized or fixed focal length lenses.
•Two years on Legacy fixed dome products.
•Two years on Spectra continuous motion applications.
•Two years on Esprit
• Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.
®
Series products (multiplexers, server, and keyboard).
®
, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
®
, Esprit®, ExSite™, and PS20 scanners, including when used in
®
and WW5700 Series window wiper (excluding wiper blades).
Series distributed network-based video products.
A
B
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department Pelco 3500 Pelco Way Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco 3500 Pelco Way Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors 473 Eccles Avenue South San Francisco, CA 94080 USA Phone: 650-737-1700 Fax: 650-737-0933
REVISION HISTORY
Manual # Date Comments
C2414M 11/99 Original version. C2414M-A 3/00 Added installation instructions for HT10V, HT10V/RC, and MT10P Enclosures. Removed instructions for E708-24 Enclosure.
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. ©Copyright 2000, Pelco. Endura and ExSite are trademarks of Pelco. All rights reserved.
Loading...