Pelco C1487M-H User Manual

®

SD5 Series

Spectra II™ and

Spectra Lite™

Dome Systems

Installation Manual

C1487M-H (1/01)

Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com
In North America and Canada: Tel [phone] • FAX [phone]

International Customers: Tel [phone] • FAX [phone]

2 Pelco Installation Manual C1487M-H (1/01)

CONTENTS

Section Page

IMPORTANT SAFEGUARDS AND WARNINGS .................................................................................................................... 4

INSTALLATION .......................................................................................................................................................................5

HARD CEILING INSTALLATION .................................................................................................................................... 6

SUSPENDED CEILING INSTALLATION ....................................................................................................................... 8

PENDANT-MOUNT INSTALLATION ............................................................................................................................. 10

SURFACE-MOUNT INSTALLATION ............................................................................................................................. 12

TROUBLESHOOTING ...........................................................................................................................................................14

APPENDIX .............................................................................................................................................................................15

SPECIFICATIONS .................................................................................................................................................................19

CERTIFICATIONS AND REGULATORY NOTICES .......................................................................................................23

WARRANTY AND RETURN INFORMATION ........................................................................................................................24

LIST OF ILLUSTRATIONS

Figure Page

1 SD5 Series Dimension Drawing ............................................................................................................................20

LIST OF TABLES

Table Page

AVideo Coaxial Cable Wiring Distances .................................................................................................................. 15

B 24 VAC Wiring Distances .......................................................................................................................................15

C Switch Settings for SW1 ........................................................................................................................................ 15

D Switch Settings for SW2 – P-Type Control ............................................................................................................ 16

E Switch Settings for SW2 – D-Type Control ............................................................................................................ 16

Pelco Installation Manual C1487M-H (1/01) 3

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.

2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it
must not be installed where exposed to rain and moisture.

3. Only use replacement parts recommended by Pelco.

4. After replacement/repair of this unit’s electrical components, conduct a resistance measurement between line and exposed parts to
verify the exposed parts have not been connected to line circuitry.

5. The installation method and materials should be capable of supporting four times the weight of the enclosure, pan/tilt, camera and
lens combination.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage
constituting a risk of electric shock is present within
this unit.

This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.

Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

MEASURES DE SECURITE IMPORTANTES

Avant d’installer ou d’utiliser ce produit, les mesures de sécurité suivantes sont à prendre:

1. Toute installation et réparation devraient être entreprises par un technicien qualifié et conformes au codes locaux.

2. A moins que cet equipement indique avoir un boitié agrée NEMA de type 3, 3R, 3S, 4, 4X, 6 ou 6P, il est uniquement conçu pour
utilisation intérieure et ne peut donc pas être en contact de pluie ou d’humidité.

3. Utiliser seulement les pièces de rechanges recommandées par Pelco.

4. Après toute installation ou réparation de la partie électrique de ce produit, une résistance entre le courant et la partie exposée devrait
être installée afin de vérifier que la partie électrique n’aie pas été en contact d’un court circuit.

5. L’installation entreprise et le matériel utilisé devraient supporter quatre fois le poids du boitié, de la tourelle, de la caméra, et de la
lentille.

Ce produit et/ou le manuel pourrait inclurent les symbols suivants:

Ce symbol indique qu’un voltage dangereux
pouvant provoquer un chock électrique est
présant dans cette unité.

RISQUE DE CHOQUE ÉLECTRIQUE.

Ce symbol indique qu’il y a des mesures
d’installation et d’entretient importantes
inclus dans le manuel de cet équipement.

Nous vous prions de bien vous familiarisez avec la manuel avant d’entreprendre toute installation.

CAUTION:

NE PAS OUVRIR.

4 Pelco Installation Manual C1487M-H (1/01)

INSTALLATION

The Spectra II™ dome and Spectra Lite™ dome shipping cartons contain three boxes. Inspect each box to make sure all parts are
present.

IN-CEILING MODELS

Back Box

1 Back box
1 Parts bag

1 Conduit fitting
1 Safety chain bracket
1 Lock nut
1 Compass tool
4T-rail clip (clip, L-bracket, screw, lock washer and nut)

Dome Drive

1 Dome drive

Lower Dome

1 Acrylic lower dome with trim ring

BACK BOX

PENDANT MODELS

Back Box

1 Back box
1Tube of thread compound

Dome Drive

1 Dome drive

Lower Dome

1 Acrylic lower dome with trim ring
1 Parts bag (O-ring and lubricant, and tube of Loctite)

BACK BOX

DOME DRIVE

DOME DRIVE

LOWER DOME

COMPASS TOOL

SAFETY BRACKET

T-RAIL CLIP

CONDUIT FITTING & LOCK NUT

LOWER DOME

THREAD

COMPOUND

LOCTITE®

222MS

O-RING

LUBE

O-RING

Pelco Installation Manual C1487M-H (1/01) 5

HARD CEILING INSTALLATION

IN-CEILING MODELS

STEP 1 - PREPARE CEILING

a. Locate the center point of the mounting location. Drill a hole in

the ceiling using a 3/32-inch drill. Insert the compass tool into
the hole.

STEP 2 - INSTALL THE BACK BOX

ATTACH SAFETY CHAIN HERE

a. Attach the conduit fitting, lock nut, and safety chain bracket.

Install a safety chain/cable (not supplied) that will support up
to 16 pounds (7.3 kg).

b. Draw a circle on the ceiling using the compass tool and a

pencil. Cut the circle out of the ceiling.

b. Turn the thumb screw and open the hinged door to the back

box. Pull wiring into the back box through the conduit fitting.
Refer to Tables A and B in the Appendix for wiring distances.

CEILING TILE

c. Compress the spring clips on the back box and push it through

the hole, until the clips spring back. Tighten the screws until
you hear a clicking noise.

6 Pelco Installation Manual C1487M-H (1/01)

24 VAC

TRANFORMER

POWER

(24 VAC ONLY)

d. Attach the wiring to the circuit board inside the back box. When

finished, close the door to the back box and turn on the power.
The red LED will light.

IMPORTANT: If the LED does not light, refer to the

shooting

section.

Trouble-

NOTE: Aux 1 - Maximum 2A at low voltage (<40V)

Aux 2 - Maximum 150 vA at 32 VDC

STEP 3 - INSTALL DOME DRIVE

SW1

ON

123

6

4

5

78

ON

SW2

1

3

2

4

5

6

8

7

SW2

LABEL

SW1

LABEL

SW2

COAXITRON
CONTROLLER

2 WIRE
CONTROLLER

SPECTRA II ONLY

+5 to +24 VDC

LOGIC GATE

(WIRING EXAMPLE)

EXTERNAL RELAY

(WIRING EXAMPLE)

CONTROLLER

VIDEO IN

+5 VDC

GREEN

TAB

TX­TX+

NOT USED
NOT USED

SWITCHES

(WIRING EXAMPLE)

AUX 2

RED

TAB

VIDEO OUT

RX-

CONTROL

RX+

(RS-422)

TX­TX+

1
2

ALARM

3

INPUTS

4
5
6
7
GROUND

(NO)
(NC)

GROUND

HEATER/FAN

(NOT USED)

RELAY

(AUX 1)

AUX 2

RS-422 TERMINATION SWITCH

00303

a. Set the DIP switches for SW1 and SW2 on the bottom of the

dome drive for the appropriate receiver address. Refer to the
labels on the dome drive or Tables C through E in the Appen­dix in the back of this manual.

b. Daisy Chain Operation Only – When connecting more than

one Spectra dome system to a single controller, terminate the
last unit in the chain (farthest from the controller). To terminate
the dome drive set the RS-422 termination switch to the left.

STEP 4 - INSTALL LOWER DOME

a. Snap the clip, on the end of the trim ring leash, into the hole on the

lip of the back box.

b. Line up the snaps on the trim ring with the mounting screws on the

back box. Snap the trim ring into the plastic snap washers on the
mounting screws.

TO USE YOUR DOME, REFER TO THE

OPERATION AND PROGRAMMING MANUAL.

c. Line up the green and red tabs with the green and red labels.

Push in on the tabs. Insert the side with the green tab, then the
side with red tab. Continue pushing on the ends of the tabs
until both sides click into place.

Pelco Installation Manual C1487M-H (1/01) 7

SUSPENDED CEILING INSTALLATION

IN-CEILING MODELS

STEP 1 - PREPARE CEILING TILE

NOTE: The ceiling tile cannot be thinner than 0.50-inch (1.27 cm) or thicker than 1.75-inches (4.45 cm).

a. Remove the ceiling tile from the ceiling. Insert the compass tool (supplied) into the center of the tile. (If necessary use a 3/32-inch bit

to drill a hole.)

b. Draw a circle on the tile using the compass tool and a pencil. Cut the circle out of the ceiling tile.

STEP 2 - INSTALL THE BACK BOX

ATTACH SAFETY CHAIN HERE

a. Attach the conduit fitting, lock nut, and safety chain bracket.

Install a safety chain/cable (not supplied) that will support up
to 16 pounds (7.3 kg).

CEILING TILE

b. Turn the thumb screw and open the hinged door to the back

box. Pull wiring into the back box through the conduit fitting.
Refer to Tables A and B in the Appendix for wiring distances.

T-RAIL CLIP
FOR

T-RAIL CLIP
FOR
CEILING TILE

CEILING TILE

c. Compress the spring clips on the back box and push it through

the hole, until the clips spring back. Tighten the screws until
you hear a clicking noise.

d. Install the ceiling tile with the back box. Attach a T-rail clip on

each side of the ceiling tile. Fasten the L-bracket to the clip
with the supplied screw and washers.

8 Pelco Installation Manual C1487M-H (1/01)

e. Attach the wiring to the circuit board inside the back box. When

finished, close the door to the back box and turn on the power.
The red LED will light.

IMPORTANT: If the LED does not light, refer to the

shooting

section.

Trouble-

NOTE: Aux 1 - Maximum 2A at low voltage (<40V)

Aux 2 - Maximum 150 vA at 32 VDC

COAXITRON
CONTROLLER

2 WIRE
CONTROLLER

+5 to +24 VDC

(WIRING EXAMPLE)

CONTROLLER

SPECTRA II ONLY

LOGIC GATE

24 VAC

TRANFORMER

VIDEO IN

TX­TX+

(WIRING EXAMPLE)

+5 VDC

NOT USED
NOT USED

SWITCHES

POWER

(24 VAC ONLY)

VIDEO OUT

RX-

CONTROL

RX+

(RS-422)

TX­TX+

1
2

ALARM

3

INPUTS

4
5
6
7
GROUND

(NO)
(NC)

GROUND

RELAY

(AUX 1)

AUX 2

STEP 3 - INSTALL DOME DRIVE

SW1

ON

123

6

4

5

78

ON

SW2

1

3

2

4

5

6

8

7

a. Set the DIP switches for SW1 and SW2 on the bottom of the

dome drive for the appropriate receiver address. Refer to the
labels on the dome drive or Tables C through E in the Appen­dix in the back of this manual.

b. Daisy Chain Operation Only – When connecting more than

one Spectra dome system to a single controller, terminate the
last unit in the chain (farthest from the controller). To terminate
the dome drive set the RS-422 termination switch to the left.

SW2

LABEL

SW1

RS-422 TERMINATION SWITCH

LABEL

SW2

00303

RED

TAB

HEATER/FAN

(NOT USED)

EXTERNAL RELAY

(WIRING EXAMPLE)

GREEN

TAB

AUX 2

c. Line up the green and red tabs with the green and red labels.

Push in on the tabs. Insert the side with the green tab, then the
side with red tab. Continue pushing on the ends of the tabs
until both sides click into place.

STEP 4 - INSTALL LOWER DOME

a. Snap the clip, on the end of the trim ring leash, into the hole on the

lip of the back box.

b. Line up the snaps on the trim ring with the mounting screws on the

back box. Snap the trim ring into the plastic snap washers on the
mounting screws.

TO USE YOUR DOME, REFER TO THE

OPERATION AND PROGRAMMING MANUAL.

Pelco Installation Manual C1487M-H (1/01) 9

PENDANT-MOUNT INSTALLATION

PENDANT MODELS

STEP 1 - MOUNT AND INSTALL THE BACK BOX

NOTE: If installing outdoors make sure the installation is properly sealed to keep moisture out.

a. Install the mount for the pendant dome. Refer to the instruc-

tions supplied with the mount. Bring the wiring for the dome

b. Turn the thumbscrew and open the hinged door located inside

the back box.
through the mount. Refer to Tables A and B in the Appendix for
wiring distances.

c. Pull wiring from the mount into the back box. d. Screw the back box into the mount. If outdoors, apply thread

compound (provided) to the threads on the back box.

STEP 2 - WIRE CIRCUIT BOARD

Attach the wiring to the interconnect circuit board inside the back
box. Close the door to the back box. Turn on power to the back
box. The red LED will light.

IMPORTANT: If the LED does not light, refer to the Trouble­shooting section.

NOTE: Aux 1 - Maximum 2A at low voltage (<40V)

Aux 2 - Maximum 150 vA at 32 VDC

COAXITRON
CONTROLLER

2 WIRE
CONTROLLER

+5 to +24 VDC

(WIRING EXAMPLE)

CONTROLLER

SPECTRA II ONLY

LOGIC GATE

24 VAC

TRANFORMER

VIDEO IN

TX­TX+

(WIRING EXAMPLE)

+5 VDC

NOT USED
NOT USED

SWITCHES

POWER

(24 VAC ONLY)

VIDEO OUT

RX-

CONTROL

RX+
TX­TX+

1
2

ALARM

3

INPUTS

4
5
6
7

GROUND

(NO)
(NC)

GROUND

(RS-422)

RELAY

(AUX 1)

AUX 2

EXTERNAL RELAY

(WIRING EXAMPLE)

AUX 2

HEATER/FAN

(NOT USED)

10 Pelco Installation Manual C1487M-H (1/01)

STEP 3 - INSTALL DOME DRIVE

SW1

ON

123

6

4

5

78

ON

SW2

1

3

2

4

5

6

8

7

SW2

LABEL

SW1

RS-422 TERMINATION SWITCH

LABEL

SW2

00303

a. Set the DIP switches for SW1 and SW2 on the bottom of the

dome drive for the appropriate receiver address. Refer to the
labels on the dome drive or tables C through E in the Appendix
in the back of this manual.

b. Daisy Chain Operation Only – When connecting more than

one Spectra dome system to a single controller, terminate the

STEP 4 - INSTALL LOWER DOME

RED

GREEN

TAB

TAB

last unit in the chain (farthest from the controller). To terminate

the dome drive set the RS-422 termination switch to the left.

c. Line up the green and red tabs with the green and red labels.

Push in on the tabs. Insert the side with the green tab, then the

side with red tab. Continue pushing on the ends of the tabs

until both sides click into place.

a. Lightly apply O-ring lubricant to the O-ring. Install the O-ring in

the groove on the trim ring of the lower dome.

NOTE: If you are install­ing an outdoor model,
plug the two-pin heater
connection in the lower
dome into the mating
connector in the back
box.

LEASH

ATTACH
LEASH TO
NEAREST
RETAINER
SCREW

MOUNTING
SCREW HOLES
FRONT & BACK

b. Attach the back box trim leash to the lower dome. Use retainer

screw (nearest to a mounting screw) inside lower dome.

c. Remove the two lower dome, mounting screws. Apply a drop

of Loctite 222MS (supplied) to each screw.

d. Push the lower dome inside the back box, line up the mounting

screw holes, and install the two mounting screws.

TO USE YOUR DOME, REFER TO THE OPERATION AND PROGRAMMING MANUAL.

Pelco Installation Manual C1487M-H (1/01) 11

SURFACE-MOUNT INSTALLATION

PENDANT MODELS

STEP 1 - REMOVE THE TOP PORTION OF THE BACK BOX

a. Turn the thumbscrew and open the

hinged door located inside the back box.

b. Unscrew the three Phillips screws lo-

cated underneath the hinged door.

c. Remove the top portion of the back box.

STEP 2 - PREPARE SURFACE AND INSTALL THE BACK BOX

NOTE: If installing outdoors
apply a sealant between the
back box and the mounting
surface

a. Determine the mounting location. Use the base of the back box as a template. Mark the fastener and center hole positions onto the

mounting surface.

b. Drill a hole in the center of the mounting surface. Pull wiring through the opening. Refer to Tables A and B in the Appendix for wiring

distances. Prepare the holes for the fasteners. Position the back box over the mounting holes and pull wiring into the back box.
Secure the back box to the mounting surface using the appropriate hardware for your installation.

24 VAC

TRANFORMER

POWER

(24 VAC ONLY)

STEP 3 - WIRE CIRCUIT BOARD

Attach the wiring to the interconnect circuit board inside the back
box. Close the door to the back box. Turn on power to the back
box. The red LED will light.

IMPORTANT: If the LED does not light, refer to the

shooting

section.

NOTE: Aux 1 - Maximum 2A at low voltage (<40V)

Aux 2 - Maximum 150 vA at 32 VDC

Trouble-

COAXITRON
CONTROLLER

2 WIRE
CONTROLLER

SPECTRA II ONLY

+5 to +24 VDC

LOGIC GATE

(WIRING EXAMPLE)

EXTERNAL RELAY

(WIRING EXAMPLE)

CONTROLLER

VIDEO IN

TX­TX+

+5 VDC

NOT USED
NOT USED

SWITCHES

(WIRING EXAMPLE)

AUX 2

VIDEO OUT

RX-

CONTROL

RX+

(RS-422)

TX­TX+

1
2

ALARM

3

INPUTS

4
5
6
7
GROUND

(NO)
(NC)

GROUND

HEATER/FAN

(NOT USED)

RELAY

(AUX 1)

AUX 2

12 Pelco Installation Manual C1487M-H (1/01)

STEP 4 - INSTALL DOME DRIVE

SW1

ON

123

6

4

5

78

ON

SW2

1

3

2

4

5

6

8

7

SW2

LABEL

SW1

RS-422 TERMINATION SWITCH

LABEL

SW2

00303

a. Set the DIP switches for SW1 and SW2 on the bottom of the

dome drive for the appropriate receiver address. Refer to the
labels on the dome drive or Tables C through E in the Appen­dix in the back of this manual.

b. Daisy Chain Operation Only – When connecting more than

one Spectra dome system to a single controller, terminate the

STEP 5 - INSTALL LOWER DOME

RED

GREEN

TAB

TAB

last unit in the chain (farthest from the controller). To terminate
the dome drive set the RS-422 termination switch to the left.

c. Line up the green and red tabs with the green and red labels.

Push in on the tabs. Insert the side with the green tab, then the
side with red tab. Continue pushing on the ends of the tabs
until both sides click into place.

a. Lightly apply O-ring lubricant to the O-ring. Install the O-ring in

the groove on the trim ring of the lower dome.

NOTE: If you are install­ing an outdoor model,
plug the two-pin heater
connection in the lower
dome into the mating
connector in the back
box.

LEASH

ATTACH
LEASH TO
NEAREST
RETAINER
SCREW

MOUNTING
SCREW HOLES
FRONT & BACK

b. Attach the back box trim leash to the lower dome. Use the

retainer screw (nearest to a mounting screw) inside lower dome.

c. Remove the two lower dome, mounting screws. Apply a drop

of Loctite (supplied) to each screw.

d. Push the lower dome inside the back box, line up the mounting

screw holes, and install the two mounting screws.

TO USE YOUR DOME, REFER TO THE OPERATION AND PROGRAMMING MANUAL.

Pelco Installation Manual C1487M-H (1/01) 13

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION

Unit does not operate.
The controller is not
communicating with the
Spectra unit.

Check to see if the red LED on the circuit
board in the back box is lit.

1. The red LED is not lit.
a. Fuse is bad.

b. 24 VAC power source is not con-

nected or back box is bad.

2. The red LED is lit.
a. Wiring is incorrect or is not fully

seated.

b. DIP switch settings are incorrect.

a. Check fuse on the circuit board. Replace fuse if

it is bad. To order a fuse from Pelco, specify the
part number FUS1.6-5X20FAST. This is a 1.6­ampere fuse, 5 x 20 mm, fast blow.

b. Use a voltmeter to check if 24 VAC is getting to

the power connector on the circuit board. If NO,
check your power supply. If YES, return the back
box to the factory for repair.

a. Check all connections to the circuit board.

Make sure that all connections are fully seated
and the board is wired correctly.

b. Check the DIP switch settings on the dome

drive (refer to Tables C, D, and E). If the unit still
does not operate, turn off power and replace
the dome drive with a good unit, if you have a
spare. Check the switch settings on the substi­tute dome drive before installing it. (If you do not
have a spare, return the dome drive and back
box to the factory.) If you substituted a dome
drive and the unit operates, the original
dome drive is bad (return the dome drive to the
factory). If the unit still does not operate,
then the circuit board is bad (return the back
box to the factory).

Fan does not operate.

Fan connections are not fully seated.

Make sure the connector for the fan is fully seated.
If the fan still does not operate, return the back box
and dome drive to the factory for repair.

Vertical roll on monitor
when switching between
cameras.

Cameras are out of phase.

If you are wiring more than one dome to the same
transformer, it is important to wire the power con­nector in each dome the same way. That is, the
wiring from one side of the transformer must be
connected to the same connector on each dome.

WARNING: Make
sure you wire power

DOME 1
POWER

to the outer connec­tors of the terminal
block and ground to
the middle connec-

DOME 2
POWER

tor. Otherwise, you
could damage the
dome.

DOME 3
POWER

14 Pelco Installation Manual C1487M-H (01/01)

APPENDIX

Table A. Video Coaxial Cable Wiring Distances

Cable Type* Maximum Distance

RG59/U 750 ft (229 m)
RG6/U 1,000 ft (305 m)
RG11/U 1,500 ft (457 m)

* Minimum cable requirements:

75 ohms impedance. All-copper center conductor.
95% braided copper shield.

Table B. 24 VAC Wiring Distances

The following are the recommended maximum distances for 24 VAC with a 10­percent voltage drop. (Ten percent is generally the maximum allowable voltage
drop for AC-powered devices.)

Wire Gauge

20 18 16 14 12 10

30 vA 94 ft 150 ft 238 ft 380 ft 603 ft 960 ft

(28 m) (45 m (115 m) (72 m) (183 m) (292 m)

75 vA 37 ft 60 ft 95 ft 152 ft 241 ft 384 ft

(11 m) (18 m) (29 m) (46 m) (73 m) (117 m)

NOTE: Input power for the dome is 24 VAC only. Power consumption is 30 vA per

dome for indoor models and 75 vA for outdoor models.
Use a 24 VAC transformer with the following minimum vA:

40 vA per dome For indoor models (without heater)
100 vA per dome For outdoor models (with heater)

Table C. Switch Settings for SW1

Control Type Switch Setting

SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

Coaxitron
P-Type Control ON OFF OFF OFF OFF OFF OFF OFF**
D-Type Control OFF ON OFF OFF OFF OFF OFF* OFF**

NOTES: Switches SW 1-3 through SW 1-6 MUST be OFF.

®

D-type control is RS-422 that is compatible with Pelco’s CM6700, MPT9500, CM8500, and Genex® controllers or with
American Dynamics control systems using the AD2083 Translator.
P-type control is RS-422 that is compatible with Pelco’s CM6700/CM9750/CM9760 and Genex control systems.

* OFF- Use with controllers that have more than 32 presets.

ON- Use with American Dynamics controllers (32 presets).

** OFF - Use with all control systems except CM9502 with variable speed keyboards.

ON - Use with CM9502 with variable speed keyboards for smoother joystick control.

OFF OFF OFF OFF OFF OFF OFF OFF**

For CM9502 with fixed speed keyboards, set switch OFF.

Pelco Installation Manual C1487M-H (01/01) 15

Table D. Switch Settings for SW2 – P-Type Control

NOTE: For Coaxitron controls, SW2 is not used; set all switches OFF. For D-type control systems, refer to Table E.

Receiver Switch Setting

Address SW2-1 SW2-2 SW2-3 SW2-4 SW2-5

1 OFF OFF OFF OFF OFF
2ONOFF OFF OFF OFF
3 OFF ON OFF OFF OFF
4ONONOFF OFF OFF
5 OFF OFF ON OFF OFF
6ONOFF ON OFF OFF
7 OFF ON ON OFF OFF
8ONONONOFF OFF

9 OFF OFF OFF ON OFF
10 ON OFF OFF ON OFF
11 OFF ON OFF ON OFF
12 ON ON OFF ON OFF
13 OFF OFF ON ON OFF
14 ON OFF ON ON OFF
15 OFF ON ON ON OFF
16 ON ON ON ON OFF

Baud Rate Switch Setting

SW2-6 SW2-7 SW2-8

2400 OFF OFF OFF
4800 ON OFF OFF
9600 OFF ON OFF

Receiver Switch Setting

Address SW2-1 SW2-2 SW2-3 SW2-4 SW2-5

17 OFF OFF OFF OFF ON
18 ON OFF OFF OFF ON
19 OFF ON OFF OFF ON
20 ON ON OFF OFF ON
21 OFF OFF ON OFF ON
22 ON OFF ON OFF ON
23 OFF ON ON OFF ON
24 ON ON ON OFF ON
25 OFF OFF OFF ON ON
26 ON OFF OFF ON ON
27 OFF ON OFF ON ON
28 ON ON OFF ON ON
29 OFF OFF ON ON ON
30 ON OFF ON ON ON
31 OFF ON ON ON ON
32 ON ON ON ON ON

Table E. Switch Settings for SW2 – D-Type Control

NOTE: For Coaxitron controls, SW2 is not used; set all switches OFF. For P-type control systems, refer to Table D.

Receiver Switch Setting

Address SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

1ONOFF OFF OFF OFF OFF OFF OFF

2 OFF ON OFF OFF OFF OFF OFF OFF

3ONONOFF OFF OFF OFF OFF OFF

4 OFF OFF ON OFF OFF OFF OFF OFF

5ONOFF ON OFF OFF OFF OFF OFF

6 OFF ON ON OFF OFF OFF OFF OFF

7ONONONOFF OFF OFF OFF OFF

8 OFF OFF OFF ON OFF OFF OFF OFF

9ONOFF OFF ON OFF OFF OFF OFF
10 OFF ON OFF ON OFF OFF OFF OFF
11 ON ON OFF ON OFF OFF OFF OFF
12 OFF OFF ON ON OFF OFF OFF OFF
13 ON OFF ON ON OFF OFF OFF OFF
14 OFF ON ON ON OFF OFF OFF OFF
15 ON ON ON ON OFF OFF OFF OFF
16 OFF OFF OFF OFF ON OFF OFF OFF
17 ON OFF OFF OFF ON OFF OFF OFF
18 OFF ON OFF OFF ON OFF OFF OFF
19 ON ON OFF OFF ON OFF OFF OFF
20 OFF OFF ON OFF ON OFF OFF OFF
21 ON OFF ON OFF ON OFF OFF OFF
22 OFF ON ON OFF ON OFF OFF OFF
23 ON ON ON OFF ON OFF OFF OFF
24 OFF OFF OFF ON ON OFF OFF OFF

Receiver Switch Setting

Address SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

25 ON OFF OFF ON ON OFF OFF OFF
26 OFF ON OFF ON ON OFF OFF OFF
27 ON ON OFF ON ON OFF OFF OFF
28 OFF OFF ON ON ON OFF OFF OFF
29 ON OFF ON ON ON OFF OFF OFF
30 OFF ON ON ON ON OFF OFF OFF
31 ON ON ON ON ON OFF OFF OFF
32 OFF OFF OFF OFF OFF ON OFF OFF
33 ON OFF OFF OFF OFF ON OFF OFF
34 OFF ON OFF OFF OFF ON OFF OFF
35 ON ON OFF OFF OFF ON OFF OFF
36 OFF OFF ON OFF OFF ON OFF OFF
37 ON OFF ON OFF OFF ON OFF OFF
38 OFF ON ON OFF OFF ON OFF OFF
39 ON ON ON OFF OFF ON OFF OFF
40 OFF OFF OFF ON OFF ON OFF OFF
41 ON OFF OFF ON OFF ON OFF OFF
42 OFF ON OFF ON OFF ON OFF OFF
43 ON ON OFF ON OFF ON OFF OFF
44 OFF OFF ON ON OFF ON OFF OFF
45 ON OFF ON ON OFF ON OFF OFF
46 OFF ON ON ON OFF ON OFF OFF
47 ON ON ON ON OFF ON OFF OFF
48 OFF OFF OFF OFF ON ON OFF OFF

(Continued on next page)

16 Pelco Installation Manual C1487M-H (01/01)

Table E. Switch Settings for SW2 – D-Type Control (continued)

Receiver Switch Setting

Address SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

49 ON OFF OFF OFF ON ON OFF OFF
50 OFF ON OFF OFF ON ON OFF OFF
51 ON ON OFF OFF ON ON OFF OFF
52 OFF OFF ON OFF ON ON OFF OFF
53 ON OFF ON OFF ON ON OFF OFF
54 OFF ON ON OFF ON ON OFF OFF
55 ON ON ON OFF ON ON OFF OFF
56 OFF OFF OFF ON ON ON OFF OFF
57 ON OFF OFF ON ON ON OFF OFF
58 OFF ON OFF ON ON ON OFF OFF
59 ON ON OFF ON ON ON OFF OFF
60 OFF OFF ON ON ON ON OFF OFF
61 ON OFF ON ON ON ON OFF OFF
62 OFF ON ON ON ON ON OFF OFF
63 ON ON ON ON ON ON OFF OFF
64 OFF OFF OFF OFF OFF OFF ON OFF
65 ON OFF OFF OFF OFF OFF ON OFF
66 OFF ON OFF OFF OFF OFF ON OFF
67 ON ON OFF OFF OFF OFF ON OFF
68 OFF OFF ON OFF OFF OFF ON OFF
69 ON OFF ON OFF OFF OFF ON OFF
70 OFF ON ON OFF OFF OFF ON OFF
71 ON ON ON OFF OFF OFF ON OFF
72 OFF OFF OFF ON OFF OFF ON OFF
73 ON OFF OFF ON OFF OFF ON OFF
74 OFF ON OFF ON OFF OFF ON OFF
75 ON ON OFF ON OFF OFF ON OFF
76 OFF OFF ON ON OFF OFF ON OFF
77 ON OFF ON ON OFF OFF ON OFF
78 OFF ON ON ON OFF OFF ON OFF
79 ON ON ON ON OFF OFF ON OFF
80 OFF OFF OFF OFF ON OFF ON OFF
81 ON OFF OFF OFF ON OFF ON OFF
82 OFF ON OFF OFF ON OFF ON OFF
83 ON ON OFF OFF ON OFF ON OFF
84 OFF OFF ON OFF ON OFF ON OFF
85 ON OFF ON OFF ON OFF ON OFF
86 OFF ON ON OFF ON OFF ON OFF
87 ON ON ON OFF ON OFF ON OFF
88 OFF OFF OFF ON ON OFF ON OFF
89 ON OFF OFF ON ON OFF ON OFF
90 OFF ON OFF ON ON OFF ON OFF
91 ON ON OFF ON ON OFF ON OFF
92 OFF OFF ON ON ON OFF ON OFF
93 ON OFF ON ON ON OFF ON OFF
94 OFF ON ON ON ON OFF ON OFF
95 ON ON ON ON ON OFF ON OFF
96 OFF OFF OFF OFF OFF ON ON OFF
97 ON OFF OFF OFF OFF ON ON OFF
98 OFF ON OFF OFF OFF ON ON OFF
99 ON ON OFF OFF OFF ON ON OFF

100 OFF OFF ON OFF OFF ON ON OFF
101 ON OFF ON OFF OFF ON ON OFF
102 OFF ON ON OFF OFF ON ON OFF
103 ON ON ON OFF OFF ON ON OFF
104 OFF OFF OFF ON OFF ON ON OFF

Receiver Switch Setting

Address SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

105 ON OFF OFF ON OFF ON ON OFF
106 OFF ON OFF ON OFF ON ON OFF
107 ON ON OFF ON OFF ON ON OFF
108 OFF OFF ON ON OFF ON ON OFF
109 ON OFF ON ON OFF ON ON OFF
110 OFF ON ON ON OFF ON ON OFF
111 ON ON ON ON OFF ON ON OFF
112 OFF OFF OFF OFF ON ON ON OFF
113 ON OFF OFF OFF ON ON ON OFF
114 OFF ON OFF OFF ON ON ON OFF
115 ON ON OFF OFF ON ON ON OFF
116 OFF OFF ON OFF ON ON ON OFF
117 ON OFF ON OFF ON ON ON OFF
118 OFF ON ON OFF ON ON ON OFF
119 ON ON ON OFF ON ON ON OFF
120 OFF OFF OFF ON ON ON ON OFF
121 ON OFF OFF ON ON ON ON OFF
122 OFF ON OFF ON ON ON ON OFF
123 ON ON OFF ON ON ON ON OFF
124 OFF OFF ON ON ON ON ON OFF
125 ON OFF ON ON ON ON ON OFF
126 OFF ON ON ON ON ON ON OFF
127 ON ON ON ON ON ON ON OFF
128 OFF OFF OFF OFF OFF OFF OFF ON
129 ON OFF OFF OFF OFF OFF OFF ON
130 OFF ON OFF OFF OFF OFF OFF ON
131 ON ON OFF OFF OFF OFF OFF ON
132 OFF OFF ON OFF OFF OFF OFF ON
133 ON OFF ON OFF OFF OFF OFF ON
134 OFF ON ON OFF OFF OFF OFF ON
135 ON ON ON OFF OFF OFF OFF ON
136 OFF OFF OFF ON OFF OFF OFF ON
137 ON OFF OFF ON OFF OFF OFF ON
138 OFF ON OFF ON OFF OFF OFF ON
139 ON ON OFF ON OFF OFF OFF ON
140 OFF OFF ON ON OFF OFF OFF ON
141 ON OFF ON ON OFF OFF OFF ON
142 OFF ON ON ON OFF OFF OFF ON
143 ON ON ON ON OFF OFF OFF ON
144 OFF OFF OFF OFF ON OFF OFF ON
145 ON OFF OFF OFF ON OFF OFF ON
146 OFF ON OFF OFF ON OFF OFF ON
147 ON ON OFF OFF ON OFF OFF ON
148 OFF OFF ON OFF ON OFF OFF ON
149 ON OFF ON OFF ON OFF OFF ON
150 OFF ON ON OFF ON OFF OFF ON
151 ON ON ON OFF ON OFF OFF ON
152 OFF OFF OFF ON ON OFF OFF ON
153 ON OFF OFF ON ON OFF OFF ON
154 OFF ON OFF ON ON OFF OFF ON
155 ON ON OFF ON ON OFF OFF ON
156 OFF OFF ON ON ON OFF OFF ON
157 ON OFF ON ON ON OFF OFF ON
158 OFF ON ON ON ON OFF OFF ON
159 ON ON ON ON ON OFF OFF ON
160 OFF OFF OFF OFF OFF ON OFF ON

(Continued on next page)

Pelco Installation Manual C1487M-H (01/01) 17

Table E. Switch Settings for SW2 – D-Type Control (continued)

Receiver Switch Setting

Address SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

161 ON OFF OFF OFF OFF ON OFF ON
162 OFF ON OFF OFF OFF ON OFF ON
163 ON ON OFF OFF OFF ON OFF ON
164 OFF OFF ON OFF OFF ON OFF ON
165 ON OFF ON OFF OFF ON OFF ON
166 OFF ON ON OFF OFF ON OFF ON
167 ON ON ON OFF OFF ON OFF ON
168 OFF OFF OFF ON OFF ON OFF ON
169 ON OFF OFF ON OFF ON OFF ON
170 OFF ON OFF ON OFF ON OFF ON
171 ON ON OFF ON OFF ON OFF ON
172 OFF OFF ON ON OFF ON OFF ON
173 ON OFF ON ON OFF ON OFF ON
174 OFF ON ON ON OFF ON OFF ON
175 ON ON ON ON OFF ON OFF ON
176 OFF OFF OFF OFF ON ON OFF ON
177 ON OFF OFF OFF ON ON OFF ON
178 OFF ON OFF OFF ON ON OFF ON
179 ON ON OFF OFF ON ON OFF ON
180 OFF OFF ON OFF ON ON OFF ON
181 ON OFF ON OFF ON ON OFF ON
182 OFF ON ON OFF ON ON OFF ON
183 ON ON ON OFF ON ON OFF ON
184 OFF OFF OFF ON ON ON OFF ON
185 ON OFF OFF ON ON ON OFF ON
186 OFF ON OFF ON ON ON OFF ON
187 ON ON OFF ON ON ON OFF ON
188 OFF OFF ON ON ON ON OFF ON
189 ON OFF ON ON ON ON OFF ON
190 OFF ON ON ON ON ON OFF ON
191 ON ON ON ON ON ON OFF ON
192 OFF OFF OFF OFF OFF OFF ON ON
193 ON OFF OFF OFF OFF OFF ON ON
194 OFF ON OFF OFF OFF OFF ON ON
195 ON ON OFF OFF OFF OFF ON ON
196 OFF OFF ON OFF OFF OFF ON ON
197 ON OFF ON OFF OFF OFF ON ON
198 OFF ON ON OFF OFF OFF ON ON
199 ON ON ON OFF OFF OFF ON ON
200 OFF OFF OFF ON OFF OFF ON ON
201 ON OFF OFF ON OFF OFF ON ON
202 OFF ON OFF ON OFF OFF ON ON
203 ON ON OFF ON OFF OFF ON ON
204 OFF OFF ON ON OFF OFF ON ON
205 ON OFF ON ON OFF OFF ON ON
206 OFF ON ON ON OFF OFF ON ON
207 ON ON ON ON OFF OFF ON ON
208 OFF OFF OFF OFF ON OFF ON ON

Receiver Switch Setting

Address SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

209 ON OFF OFF OFF ON OFF ON ON
210 OFF ON OFF OFF ON OFF ON ON
211 ON ON OFF OFF ON OFF ON ON
212 OFF OFF ON OFF ON OFF ON ON
213 ON OFF ON OFF ON OFF ON ON
214 OFF ON ON OFF ON OFF ON ON
215 ON ON ON OFF ON OFF ON ON
216 OFF OFF OFF ON ON OFF ON ON
217 ON OFF OFF ON ON OFF ON ON
218 OFF ON OFF ON ON OFF ON ON
219 ON ON OFF ON ON OFF ON ON
220 OFF OFF ON ON ON OFF ON ON
221 ON OFF ON ON ON OFF ON ON
222 OFF ON ON ON ON OFF ON ON
223 ON ON ON ON ON OFF ON ON
224 OFF OFF OFF OFF OFF ON ON ON
225 ON OFF OFF OFF OFF ON ON ON
226 OFF ON OFF OFF OFF ON ON ON
227 ON ON OFF OFF OFF ON ON ON
228 OFF OFF ON OFF OFF ON ON ON
229 ON OFF ON OFF OFF ON ON ON
230 OFF ON ON OFF OFF ON ON ON
231 ON ON ON OFF OFF ON ON ON
232 OFF OFF OFF ON OFF ON ON ON
233 ON OFF OFF ON OFF ON ON ON
234 OFF ON OFF ON OFF ON ON ON
235 ON ON OFF ON OFF ON ON ON
236 OFF OFF ON ON OFF ON ON ON
237 ON OFF ON ON OFF ON ON ON
238 OFF ON ON ON OFF ON ON ON
239 ON ON ON ON OFF ON ON ON
240 OFF OFF OFF OFF ON ON ON ON
241 ON OFF OFF OFF ON ON ON ON
242 OFF ON OFF OFF ON ON ON ON
243 ON ON OFF OFF ON ON ON ON
244 OFF OFF ON OFF ON ON ON ON
245 ON OFF ON OFF ON ON ON ON
246 OFF ON ON OFF ON ON ON ON
247 ON ON ON OFF ON ON ON ON
248 OFF OFF OFF ON ON ON ON ON
249 ON OFF OFF ON ON ON ON ON
250 OFF ON OFF ON ON ON ON ON
251 ON ON OFF ON ON ON ON ON
252 OFF OFF ON ON ON ON ON ON
253 ON OFF ON ON ON ON ON ON
254 OFF ON ON ON ON ON ON ON

18 Pelco Installation Manual C1487M-H (1/01)

SPECIFICATIONS

MECHANICAL

Construction

Back box: Aluminum
Dome drive: Aluminum, ABS plastic
Lower dome: Acrylic

Cable Entry

In-Ceiling: .75-inch (1.91 cm) conduit fitting
Pendant: Through 1.5-inch (3.81 cm) NPT pendant mount

Pan Movement: 360° continuous pan rotation

Vertical Tilt: Unobstructed +2° to -92°

Manual Pan/Tilt Speeds*

Pan

Spectra II: 0.1°-80°/sec manual operation, 150°/sec turbo
Spectra Lite: 0.5°-80°/sec manual operation, 150°/sec turbo

Tilt

Spectra II: 0.1°-40°/sec
Spectra Lite: 0.5°-40°/sec

Preset Speeds

Pan: 250°/sec
Tilt: 200°/sec

* For variable-speed operation an appropriate controller is required. With fixed-speed controllers, Spectra II and Spectra Lite pan/tilt

speed is 24°/sec. The CM6700 controller with the KBD200 keyboard has programmable fixed speeds.

ELECTRICAL

Input Voltage: 18-30 VAC, 24 VAC nominal

Input Power

In-ceiling: 30 vA
Indoor pendant: 30 vA
Outdoor pendant: 75 vA

Fuse: 1.6 A

Relay Contacts AUX 1 AUX 2 Output

Type: Form C Open collector transistor output
Voltage: Low voltage (<40 V) 32 VDC maximum
Current: 2 A maximum 150 mA maximum

GENERAL

Environment

In-Ceiling: Indoor only
Pendant: Indoor/outdoor

Operating Range

In-Ceiling: 32° to 140°F (0° to 60°C) intermittent operation; 32° to 122°F (0° to 50°C) continuous operation
Pendant

Without Heater: 32° to 140°F (0° to 60°C) absolute maximum operating temperature; 32° to 122°F (0° to 50°C) sustained

With Heater: (Assumes no wind chill factor; for detailed test conditions, contact Pelco.)

maximum operating temperature

Maximum operating temperature: 140°F (60°C) absolute maximum; 122°F (50°C) sustained maximum
Minimum operating temperature: -60°F (-51.11°C) absolute minimum; minimal icing at -50°F (-45.56°C)
sustained minimum; prevents icing at -40°F (-40°C) sustained minimum; de-ices .1 inch (2.5 mm) within 3
hours after power-up

Pelco Installation Manual C1487M-H (1/01) 19

Dimensions: See Figure 1

Ratings: NEMA Type 1–In-ceiling back boxes, all dome drives

NEMA Type 4X–Pendant back boxes
IP 66–Pendant back boxes

Weight Unit Shipping

In-Ceiling
Back Box: 2.6 lb (1.18 kg) 4 lb (1.81 kg)
Dome Drive: 2.65 lb (1.20 kg) 5 lb (2.27 kg)
Lower Dome: .19 lb (.09 kg) 1 lb (.45 kg)
Pendant
Back Box: 2.85 lb (1.28 kg) 5 lb (2.27 kg)

Add 1.25 lbs (.57 kg) for heater and sun shield

Dome Drive: 2.65 lb (1.20 kg) 5 lb (2.27 kg)
Lower Dome: 1.30 lb (.59 kg) 2.20 lb (1.0 kg)

Add .25 lbs (.11 kg) for heater

TOP PORTION OF BACK BOX
IS REMOVABLE FOR SURFACE
MOUNT APPLICATIONS

7.25 (18.13)

6.60 (16.76)

DOME IS SECURED
TO CEILING BY
MOUNTING BRACKET

8.52

(21.64)

5.25

13.34)

3.25

(8.26)

10.90

(27.69)

5.90 (14.99)

8.25 (20.96)

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES.

5.90

(14.99)

Figure 1. SD5 Series Dimension Drawing

6.75

(17.15)

(14.80)

5.83

20 Pelco Installation Manual C1487M-H (1/01)

CAMERAS

COLOR

Signal Format: NTSC (Spectra II dome drive models DD5BC, DD5BC22, and DD5BCBW)

Scanning System: 2:1 interlace

Image Sensor: 1/4-inch interline transfer CCD

Effective Pixels

Horizontal Resolution

Lens

Focal Length

(Spectra II and Spectra Lite)

PAL

(Spectra II dome drive models DD5BC-X, DD5BC22-X, and DD5BCBW-X)

NTSC (Spectra Lite dome drive model DD5TAC)
PAL (Spectra Lite dome drive model DD5TAC-X)

NTSC Spectra II: 768 (H) x 494 (V)
PAL Spectra II: 752 (H) x 582 (V)

NTSC Spectra Lite: 510 (H) x 492 (V)

PAL Spectra Lite: 500 (H) x 582 (V)

Spectra II: >470 TV lines
Spectra Lite: 470 TVL (NTSC)

Minimum f-stop

Spectra II

16X: F1.4
18X: F1.4
22X: F1.6

Spectra Lite: F1.6

Spectra II

16X: 4 mm to 64 mm optical
18X: 4.1 mm to 73.8 mm optical
22X: 4 mm to 88 mm optical

Spectra Lite: 3.9 mm to 63 mm optical

460 TVL (PAL)

Zoom Ratio

Spectra II

16X: 16X optical zoom, 8X electronic zoom
18X: 18X optical zoom, 4X electronic zoom
22X: 22X optical zoom, 8X electronic zoom

Spectra Lite: 16 optical zoom

Digital Slow Shutter: Auto/manual speed selection

Horizontal Angle of View

Spectra II

16X: 47° (at 4 mm wide zoom),

18X: 48° (at 4.1 mm wide zoom),

22X: 47° (at 4 mm wide zoom),

Spectra Lite: 45° (at 3.9 mm wide zoom),

MTBF

16X: >2 million cycles at room temperature (zoom, focus, irs)
18X: >500,000 cycles at room temperature (zoom, focus, irs)
22X: >2 million cycles at room temperature (zoom, focus, irs)
Spectra Lite: >1 million cycles at room temperature (zoom, focus, irs)

Focus: Automatic and manual override

3° (at 64 mm telephoto zoom)

2.7° (at 73.8 mm telephoto zoom)

2° (at 88 mm telephoto zoom)

3° (at 63 mm telephoto zoom)

Pelco Installation Manual C1487M-H (1/01) 21

Sensitivity

Spectra II

16X: .05 lux at 1/2-second shutter speed
18X: .2 lux at 1/4-second shutter speed (color)

22X: .07 lux at 1/1.5-second shutter speed

Spectra Lite: 1 lux at f1.6 at signal level of 40 IRE, gain high (AGC on)

Sync System: AC line lock, phase adjustable via remote control*

White Balance: Automatic with manual override*

Shutter Speed Models

DD5BC, DD5BC22,

and DD5AM: 1/2-1/30,000*

DD5BC-X, DD5BC22-X,

and DD5AM-X: 1/1.5 to 1/30,000*
DD5BCBW: 1/4 to 1/10,000*
DD5BCBW-X: 1/3 to 1/10,000*

DD5TAC: 1/60 to 1/10,000*

DD5TAC-X: 1/50 to 1/10,000*

Iris Control

Spectra II: Automatic with manual override*
Spectra Lite: Automatic with manual override*

Gain Control: Automatic with manual override*

Video Output

NTSC: .714V ± .07V (100 IRE ± 10 IRE)
PAL: .7V ± .07V

.013 lux at 1/4-second shutter speed (black & white)

Signal to Noise Ratio: >46 dB

MONOCHROME

Signal Format: EIA (model DD5AM)

Scanning System: 2:1 interlace

Image Sensor: 1/4-inch interline transfer CCD

Horizontal
Resolution: >500 TV lines

Effective Pixels

EIA: 768 (H) x 494 (V)
CCIR: 752 (H) x 582 (V)

Lens

Minimum f-stop: F1.4
Focal Length: 4 mm to 64 mm optical
Zoom Ratio: 16X optical zoom, 8X electronic zoom
Horizontal
Angle of View: 47° (at 4 mm wide zoom),

MTBF: >2 million cycles at room temperature (zoom, focus, iris)
Focus: Automatic with manual override

Sensitivity

EIA: .1 lux at f1.4, AGC gain 26.5 dB, signal level 40 IRE, without IR cut filter
CCIR: .1 lux at f1.4, AGC gain 29.5 dB, signal level 300 mV, without IR cut filter

(Spectra II Only)

CCIR (model DD5AM-X)

3° (at 64 mm telephoto zoom)

Signal Process: DSP-3R

Sync System: AC line lock, phase adjustable via remote control*

22 Pelco Installation Manual C1487M-H (1/01)

Shutter Speed: Automatic (electronic iris)/manual

EIA: 1/60-1/30,000
CCIR: 1/50-1/30,000

Iris Control: Automatic with manual override*

Gain Control: Automatic with manual override*

Video Output

EIA: .714V ± .07V (100 IRE ± 10 IRE)
CCIR: .7V ± .07V

Signal to Noise Ratio: >46 dB

* Manual control of camera setup functions can be done with CM6700, CM8500, CM9500, CM9760 and MPT9500 controllers, but not

with CM7500, MPT9000 or KBD9000 controllers.

(Design and product specifications subject to change without notice.)

CERTIFICATIONS AND REGULATORY NOTICES

CE, Class A (models DD5BC-X and DD5BC22-X).
CE, Class B (models BB5A-F, BB5A-PB, BB5A-PG, BB5A-PG-E, BB5T-F, BB5T-PB, BB5T-PG, BB5T-PG-E, DD5TAC-X, DD5AM-X,
and DD5BCBW-X). (Model BB5A-PSG-E, Pending)
UL/cUL (models BB5A-F, BB5A-PB, BB5A-PG, BB5A-PG-E, DD5AM, BB5T-F, BB5T-PB, BB5T-PG, BB5T-PG-E, DD5TAC, DD5BC,
DD5BC22, and DD5BCBW). (Model BB5A-PSG-E, Pending)
FCC Class A (model DD5BC22)
FCC Class B (models DD5AM, DD5BC, DD5TAC, and DD5BCBW).

Suitable for use in environmental air handling spaces (BB5A-F and BB5T-F).

FCC Class B meets more stringent requirements than FCC Class A.

The following applies to the DD5AM, DD5BC, and DD5TAC models.

FCC Class B - This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However there is no guarantee that the interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

The following applies to the DD5BC22 model.

FCC Class A - This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.

Pelco Installation Manual C1487M-H (1/01) 23

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

®

• Three years on Genex

• Three years on Camclosure® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.

•Two years on standard motorized or fixed focal length lenses.

•Two years on Legacy
fixed dome products.

•Two years on Spectra
continuous motion applications.

•Two years on Esprit

• Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for
such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused,
whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.

Series products (multiplexers, server, and keyboard).

®

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

®

, Esprit®, ExSite™, and PS20 scanners, including when used in

®

and WW5700 Series window wiper (excluding wiper blades).

™

Series distributed network-based video products.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or
[phone] to obtain a Repair Authorization number (RA), and provide the following
information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.

Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at
[phone] or [phone] to obtain an authorization number (CA number if returned
for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

REVISION HISTORY

Manual # Date Comments

C1487M 7/98 Original version.

C1487M-A 11/98 Revised the manual to incorporate Spectra Lite material. Added material on CCIR and EIA monochrome cameras, and PAL

C1487M-B 2/99 Changed Spectra Lite model numbers, and added comments that the line sync feature is not functional for the DD5T-C model

C1487M-C 7/99 Added a note relating to running patterns when an alarm activates. Changed the preset tilt speed from 100 to 200 degrees/

C1487M-D 7/99 Changed Spectra Lite camera zoom from 12X to 16X. Changed line sync and auto focus material to include Spectra Lite as

C1487M-E 9/99 Replaced the standard Spectra II DD5AC and DD5AC-X cameras with model DD5BC and DD5BC-X LowLight color cam-

C1487M-F 3/00 Separated into two manuals - Installation Manual and Operation and Programming Manual.

C1487M-G 5/00 Added information on Spectra II Color/Black and White.

C1487M-H 1/01 Added step to dome drive installation instructions referencing the new RS-422 termination switch. Revised specifications

® Pelco, the Pelco logo, Spectra, Genex, Legacy, and Coaxitron are registered trademarks of Pelco. © Copyright 2001, Pelco. All rights reserved.
™ Spectra II, Spectra Lite, Esprit, and Camclosure are trademarks of Pelco. U.S. Patent No. 5,931,432.
® Loctite is a registered trademark of Loctite Corporation.

color camera. Revised material in Section 5.11.21.2, Programming Limit Stops. Revised Section 6.0, Troubleshooting. Changed
the fixed-speed controller rate in Section 8.0, Specifications.

of Spectra Lite. Changed power specifications for indoor models from 25 vA to 30 vA and for outdoor models from 90 vA to
75 vA. Revised maximum temperature operating ranges. Revised color camera specifications.

3/99 Changed auto iris material to include Spectra Lite as well as Spectra II.

second. Added model number and specifications for Spectra Lite PAL camera. Revised manual to new format.

well as Spectra II. Removed auto iris peak and auto sharpness options for Spectra Lite. Added white balance hue option for
Spectra Lite and removed R-B and M-G white balance options for Spectra Lite. Revised Spectra Lite camera specifications.

eras. Added optional 176X color models. Revised main menu access documentation to include the KBD4000/KBD4002/
KBD4000V keyboards. Added material on LowLight limit. Revised material on shutter speed and zoom. Added material on
zone overlap and priorities. Revised color camera specifications.

and certifications.