Pelco C1457M-C User Manual

C1457M-C (1/01)
LD5 Series
Spectra® Lower Domes

®

3500 Pelco Way
Clovis, CA 93612-5699
USA

In North America & Canada:
Tel [phone]
FAX [phone]

International Customers:
Tel [phone]
FAX [phone]

www.pelco.com

The LD5 Series of lower domes is part of the SD5 Series of Spectra® dome systems.

IN-CEILING MODELS

1. Refer to Figure 1. Snap the clip on the end of the trim ring leash into the hole on the lip of
the back box next to one of the mounting screws.

2. Line up the snaps on the trim ring with the mounting screws on the back box. Snap the
trim ring into place on the plastic snap washers on the mounting screws.

PENDANT MODELS

1. Remove the O-ring and O-ring lubricant from the parts bag. Apply lubricant to the O-ring.
Install the O-ring in the groove on the trim ring of the lower dome.

2. Refer to Figure 2. Hanging down from the back box is a short cable (the trim ring leash).
Hold up the lower dome near the back box so that the trim ring leash touches the lower
dome. Line up the two screw holes in the trim ring of the lower dome with the two screw
holes in the back box. Place a finger on the edge of the trim ring where the leash touches
the lower dome.

3. Look inside the lower dome and note which of the six retainer screws is closest to your
finger. Remove this screw and attach the trim ring leash to the screw. Reinstall the screw
securely and make sure the leash will hold the lower dome.

4. If you are installing an outdoor model, plug the two-pin heater connection in the lower
dome into the mating connector in the back box.

5. Remove the two mounting screws from the lower dome. Apply a drop of Loctite® (sup­plied) to each screw.

6. Push the lower dome inside the back box, line up the screw holes, and install the two screws.

LEASH

AT TAC H
LEASH TO

00242

NEAREST
RETAINER
SCREW

MOUNTING
SCREW HOLES
FRONT & BACK

00243

Figure 1. Lower Dome Installation, In-Ceiling Models Figure 2. Lower Dome Installation, Pendant Models

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

®

• Three years on Genex

• Three years on Camclosure® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.

•Two years on standard motorized or fixed focal length lenses.

•Two years on Legacy
fixed dome products.

•Two years on Spectra
continuous motion applications.

•Two years on Esprit

• Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for
such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused,
whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.

Series products (multiplexers, server, and keyboard).

®

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

®

, Esprit®, ExSite™, and PS20 scanners, including when used in

®

and WW5700 Series window wiper (excluding wiper blades).

™

Series distributed network-based video products.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or
[phone] to obtain a Repair Authorization number (RA), and provide the following
information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.

Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at
[phone] or [phone] to obtain an authorization number (CA number if returned
for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

REVISION HISTORY

Manual # Date Comments

C1457M-B 7/98 Original version.

C1457M-C 1/01 Revised installation instructions.

® Pelco, the Pelco logo, and Spectra are registered trademarks of Pelco. © Copyright 2001, Pelco.
™ Spectra II and Spectra Lite are trademarks of Pelco. All rights reserved.

2/99 Changed manual to new format.
9/99 Removed manual references from the first paragraph.