Pelco C1455SM-C User Manual

®

SD5 Series

Spectra® Dome

Maintenance/

Service Manual

C1455SM-C (5/00)

Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com
In North America and Canada: Tel [phone] • FAX [phone]

International Customers: Tel [phone] • FAX [phone]

DESCRIPTION

This maintenance/service manual consists of exploded assembly diagrams and parts lists.
Use this manual when ordering replacement parts for Spectra® domes in the SD5 Series.

BACK BOX ELECTRONIC ASSEMBLY REMOVAL

To remove the back box electronic assembly:

1. Turn off power.

2. Open the interconnect door and disconnect all wiring to the back box.

3. Use an 11/32 socket driver to remove the three 8-32 washers and nuts that hold the
electronic assembly to the back box. When the screws are removed, the interconnect
back box receptacle will drop down.

It may be necessary to move the open interconnect door past 90° vertical toward the
side of the back box to release the door from the built-in grounding strip (and free the
interconnect back box receptacle).

4. Remove the interconnect back box receptacle with the electronic components from the
back box.

2 Pelco Manual C1455SM-C (5/00)

EXPLODED ASSEMBLY DIAGRAMS

3

4

5

12

6

11

2

10

9

1

7

8

Figure 1. Exploded Assembly Diagram–Back Box, In-Ceiling and Pendant Models

Table A. Exploded Assembly Parts List–Back Box, In-Ceiling and Pendant Models

Item Qty Description Part Number

12Trim ring snap cap 70610036
21In-ceiling back box 7064020COMP
31Safety chain bracket 7064014COMP
41Conduit fitting 70610040
52Spring clip 70610027
63Push nut bolt retainer, #8 ZH810000
72Screw, 8-32 x 3.50-inch, Phillips, pan head, ZH8-32X3-50SPP
83Screw, 8-32 x .375-inch, Phillips, pan head, (pendant only) ZH8-32X.375SPP
93Internal tooth lock washer, #8 (pendant only) ZH8LWSIS

10 1 Pendant back box, black 7064034BCOMP

1 Pendant back box, gray 7064034GCOMP
11 1 Gasket (pendant only) 70610012
12 1 Pendant top mount, black 7064032BCOMP

1 Pendant top mount, gray 7064032GCOMP

NS 1 Sun shield, light gray (optional) 7064033COMP
NS 3 Screw, 6-32 x 5/16-inch, pan head, Phillips, gray (sun shield only) ZH6-32X.312GRAY
NS 3 Internal tooth lock washer, #6 (sun shield only) ZH6LWSIS

Pelco Manual C1455SM-C (5/00) 3

12

1

2

3

11

10

4

5

9

8

6

7

Figure 2. Exploded Assembly Diagram–Back Box Electronic Assembly

Table B. Exploded Assembly Parts List–Back Box Electronic Assembly

Item Qty Description Part Number

11Spectra interconnect back box receptacle 70610016
23Flat washer, #8 ZH188X435X60C
33Nut, 8-32 ZH8-32NUTSH
45Spacer, .25-inch O.D. x .187-inch SPA9200
51Interconnect door 7064039COMP
6122-position connector CN12-3311-1022
72Screw, 4-40 x .3125-inch, Phillips, pan head ZH4-40X.312SPP
810Internal tooth lock washer, #4 ZH4LWSIS
91Thumbscrew, 8-32 x .5625-inch ZH8-32THUMSCW

10 1 Spectra Lite™ interconnect circuit board PA05-0007-01D0

Spectra II™ interconnect circuit board PA05-0007-00D0
11 1 Fan assembly, 12 VDC 7061007
12 1 Fan finger guard 7064002COMP

4 Pelco Manual C1455SM-C (5/00)

4

3

1

2

Figure 3. Exploded Assembly Diagram–Lower Dome, In-Ceiling Models

Table C. Exploded Assembly Parts List–Lower Dome, In-Ceiling Models

Item Qty Description Part Number

11 Acrylic dome (smoked) 70610005-12

1 Acrylic dome (clear) 70610005-05
1 Acrylic dome (chrome) 70610005-02

1 Acrylic dome (gold) 70610005-03
21 Trim ring 70610030
32 Safety stop and latch 7064019COMP
44 Screw, M3 x 5, Torx ZHM3X5BPT

NS 1 Trim ring leash assembly 70610017

NS = Not Shown

Pelco Manual C1455SM-C (5/00) 5

8

6

3

1

4

7

2

5

Figure 4. Exploded Assembly Diagram–Lower Dome, Pendant Models

Table D. Exploded Assembly Parts List–Lower Dome, Pendant Models

Item Qty Description Part Number

11Acrylic dome (smoked) 70610005-12

1 Acrylic dome (clear) 70610005-05
1 Acrylic dome (chrome) 70610005-02
1 Acrylic dome (gold) 70610005-03

21Trim ring (black) 7064085BCOMP

1Trim ring (gray) 7064085GCOMP
31Lower dome retainer 70610019
42Gasket GS01-0002-0430
52Screw, 6-32 x 1/4", pan head, Phillips, black ZH6-32X.250BPP

2 Screw, 6-32 x 5/16", pan head, Phillips, gray ZH6-32X.312GRAY
66Screw, 6-32 x 1/4", pan head, Phillips ZH6-32X.250SPP
71O-ring ZH69-EP8X.139
86Internal tooth lock washer, #6 ZH6LWSIS

6 Pelco Manual C1455SM-C (5/00)

1

3

2

Figure 5.

Exploded Assembly Diagram–

Heater Segment in Back Box

4

Exploded Assembly Parts List–

Table E.

Heater Segment in Back Box

6

Item Qty Description Part Number

5

12Fan, 1 W, 12 VDC 7061007
22Fan shroud and heater bracket 7064035COMP
32Heater pad, 15 W, 24 VAC HT01-0321-0202
46Nut, 4-40 ZH4-40NUTSH
54Screw, 4-40 x 5/8", ZH4-40X.625SPP

pan head, Phillips

66Internal tooth lock washer, #4 ZH4LWSIS
NS 1 Fan rectifier circuit board PCB9000277ASSY
NS 1 Thermostat TH01-8570-0100

On at 70°F (21°C)
Off at 85°F (29°C)

NS 1 Fan finger guard 7064002COMP

NS = Not shown

2

3

1

Figure 6. Exploded Assembly Diagram–Heater Segment in Lower Dome

Table F. Exploded Assembly Parts List–Heater Segment in Lower Dome

Item Quantity Description Part Number

11 Heater bracket 7064041COMP
21 Thermostat EH5510049A

On at 40°F (4°C)
Off at 60°F (16°C)

31 Heater pad, 30 W, 24 VAC HT01-0621-20.5

Pelco Manual C1455SM-C (5/00) 7

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

®

• Three years on Genex

• Three years on Camclosure® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.

•Two years on standard motorized or fixed focal length lenses.

•Two years on Legacy
fixed dome products.

•Two years on Spectra
continuous motion applications.

•Two years on Esprit

• Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for
such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused,
whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.

Series products (multiplexers, server, and keyboard).

®

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

®

, Esprit®, ExSite™, and PS20 scanners, including when used in

®

and WW5700 Series window wiper (excluding wiper blades).

™

Series distributed network-based video products.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or
[phone] to obtain a Repair Authorization number (RA), and provide the following
information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.

Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at
[phone] or [phone] to obtain an authorization number (CA number if returned
for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

REVISION HISTORY

Manual # Date Comments

C1455SM 5/98 Original version.

6/98 Revised drawings to show new pendant top mount. Revised parts lists to show new pendant top mount and new

pendant lower dome retainer.

C1455SM-A 10/98 Changed the title of the manual. Added Class B regulatory notice. Revised Section 2.0, Description, to include

information on the Spectra (Version 3.0), Spectra II and Spectra Lite. Revised Section 2.1.1, SD5 Series In-Ceiling
Components; Section 2.1.2, SD5 Series Pendant Components. Removed Section 2.2, Certifications. Revised Section

3.0, Troubleshooting. Revised Tables A and B in Section 5.0, Exploded Assembly Diagrams, to include new part
numbers for back box interconnect doors. Added two figures to Section 6.0, Circuit Board Components and Wiring.

C1455SM-B 2/99 Revised Spectra Lite model numbers.

3/99 Revised Tables A and B to add gasket/spacer. Removed FCC Class B notice.
6/99 Added Spectra Lite™ PAL camera model. Revised Figure 2 and Table A to reflect removal of the connector rings on

the back box for in-ceiling Spectra models.
8/99 Added DD5TAC and DD5TAC-X Spectra Lite models. Changed to new format.
10/99 Added DD5BC and DD5BC-X as the standard Spectra II dome drives. Added optional DD5BC22 and DD5BC22-X

Spectra II dome drives.

C1455SM-C 5/00 Revised to new service manual layout. Removed the following sections: Models, Troubleshooting, Maintenance, and

Circuit Board Components and Wiring. Revised illustrations and parts lists.

Pelco, the Pelco logo, Spectra, Genex, Legacy, and PelcoVision are registered trademarks of Pelco. © Copyright 2000, Pelco.
Spevtra II, Spectra Lite, Esprit and Camclosure are trademarks of Pelco. All rights reserved.

8 Pelco Manual C1455SM-C (5/00)