Pelco C1095M User Manual

C1095M

INSTALLATION MANUAL
ICIDRD INTERFACE CABLE
FOR INTER-CHECK P.O.S. SYSTEMS

®

1.0 SCOPE

This manual covers the interface for the ICIDRD
interface cable for the Wayne Dresser Plus 1, Plus 2,
and Plus 3 registers.

The following should be noted prior to installation:

1. This PELCO P.O.S. interface utilizes the

display port of the Wayne Dresser register.

WARNING:

This interface is not a printer
connection. Plugging this interface
into the printer port will damage
the interface.

2.0 INSTALLATION

2.1 LOCATING THE CASH REGISTER
DISPLAY CONNECTION

1. Locate the port labeled DISPLAY at the rear of

the register.

6. Refer to Figure 1 or Figure 2 for the proper
wiring configuration to your Inter-Check unit.

7. Make sure all connections are tight.

8. Check register and display for proper opera­tion.

2.2 INTER-CHECK UNIT PROGRAMMING

1. Enter the MAIN MENU by pressing [ENTER]
in the monitoring mode.

2. Inter-Check 1000S users press [1] (CHAN-
NEL SETUP).

Inter-Check 2000D users press [1] or [2] de-
pending on the channel you are using for data
display.

3. Press [2] in the CHANNEL MENU (DATA
FORMAT/COMMUNICATION PROTO­COL).

4. Press [ENTER] or the arrow keys on your
keyboard/keypad until you reach RS232
STANDARD PRINTER.

2. If the display port is not labeled, follow the
cable from the customer display back to the
register. The connector you need to locate will
be a 9-pin D-SUB variety.

3. After locating this connector, unplug from the
cash register.

4. Plug PELCO's display interface directly into
the register display port.

5. Plug the register display cable back into the
PELCO interface.

PELCO Manual C1095M — 4/94 1

5. Press [ESC] to save this selection.

6. Program the Communication Setup values
according to Table I. Consult your Inter-Check
manual for pertinent programming informa­tion.

7. Press [ESC] to return to monitoring mode and
test for proper operation.

Listed below are the parameters the
grammed into the Inter-Check unit for proper operation.

Table I. Typical Inter-Check Parameters

(for Wayne Dresser Display)

Inter-Check

Channel Parameters Protocol

must be pro-

2.3 INTER-CHECK WIRING KITS

The wiring configurations shown in Figure 1 and 2 are
a key component to your installation.

• Part #ICI1000WK is used with ICI1000SE
and ICI1000SI installations. This kit includes
the following components:

9600 baud RS232 Standard Printer
8 Bits
Off parity
NRZ
ASCII
Data Non-Invert

–2RJ14 phone jacks
–1Straight-through 6 conductor phone

cable

• Part # ICI2000WK is used with ICI2000D
installations. This kit includes the following
components:

–3RJ14 phone jacks
–1Straight-through 6 conductor phone

cable

Figure 1. Wiring Configuration for One (1) Wayne Dresser Register (Display)

2 PELCO Manual C1095M — 4/94

Figure 2. Wiring Configuration for Two (2) Wayne Dresser Registers (Displays)

PELCO Manual C1095M — 4/94 3

3.0 WARRANTY AND RETURN
INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved
defective in material or workmanship for a period of one year after the date
of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex

keyboard).

• Three years on Camclosure

CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,
and MC3651H-2X camera models, which have a five-year warranty.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy

DF5/DF8 Series fixed dome products.

• Two years on Spectra

ing when used in continuous motion applications.

• Two years on Esprit

wiper blades).

• Eighteen months on DX Series digital video recorders, NVR300

Series network video recorders, and Endura
network-based video products.

• One year (except video heads) on video cassette recorders (VCRs).

Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in

continuous motion applications (that is, preset scan, tour and auto scan
modes).

Pelco will warrant all replacement parts and repairs for 90 days from the
date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to Pelco, Clovis, California. Repairs made necessary by
reason of misuse, alteration, normal wear, or accident are not covered
under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or
loss resulting from the specific use or application made of the Products.
Pelco’s liability for any claim, whether based on breach of contract,
negligence, infringement of any rights of any party or product liability,
relating to the Products shall not exceed the price paid by the Dealer to
Pelco for such Products. In no event will Pelco be liable for any special,
incidental or consequential damages (including loss of use, loss of profit
and claims of third parties) however caused, whether by the negligence
of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The
Dealer may also have additional rights, which are subject to variation from
state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289­9100 or [phone] to obtain a Repair Authorization number (RA),
and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice

number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall
under the warranty conditions stated above, please include a written
explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by
which the item was received by Pelco.

®

Series products (multiplexers, server, and

®

and fixed camera models, except the

®

, CM6700/CM6800/CM9700 Series matrix, and

®

, Esprit®, ExSite™, and PS20 scanners, includ-

®

and WW5700 Series window wiper (excluding

™

Series distributed

RETURNS

In order to expedite parts returned to the factory for repair or credit, please
call the factory at [phone] or [phone] to obtain an
authorization number (CA number if returned for credit, and RA number
if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking
and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the
assigned CA or RA number and freight should be prepaid. Ship to the
appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto
Rico, send goods to:

If you are located outside the continental U.S., Alaska, Hawaii or Puerto
Rico and are instructed to return goods to the USA, you may do one of the
following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:

If the goods are to be sent by a FREIGHT FORWARDER, send the goods
to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

PELCO

3500 Pelco Way, Clovis, CA 93612-5699

[phone] • [phone]

FAX [phone] or [phone]

Pelco, the Pelco logo, Camclosure, Esprit,
Genex, Legacy, and Spectra are registered
trademarks of Pelco.
Endura and ExSite are trademarks of Pelco.

© Copyright 1994, Pelco. All rights reserved.

4 PELCO Manual C1095M — 4/94

(Product specifications subject to change without
notice.)

C1095M