Pelco BU-ADAPTER User Manual

Figure 1 Installation Guide

INSTALLATION

BU-ADAPTER

C3911M (03/12)

Important Safety Instructions

1. Installation and servicing should be done only by qualified service personnel and conform to all local codes.

2. Use only installation methods and material capable of supporting four times the maximum specified load.

3. Use stainless steel hardware to fasten the mount to outdoor surfaces.

4. To prevent damage from water leakage when installing a mount outdoors on a roof or wall, apply sealant around the bolt holes between the mount
and mounting surface.

Description

The BU-ADAPTER is used when installing the BU Series camera system to a wall or ceiling that requires surface mounted conduit.

It can be used with specific conduit boxes. See “Specifications” for details.

Package Contents

• One installation manual

• One rubber and three M4*0.7P, 12mm screws (for BU4/BU5 series only)

• One rubber and four M4*0.7P, 15mm screws (for BU6 series only)

Note: The cable hole of rubber for BU4/BU5 series is smaller than BU6 series.

Installation

You can use BU-Adapter with the recommended conduit boxes to protect cables from rain, heat, vandals and other
harsh factors and make a tidy, professional installation on a surface mount installation.

Descriptions for the Figure 1 Installation Guide (typical):

① Camera bracket(BU4/BU5 series shown)
② Camera cables
③ Rubber of BU-Adapter
④ Screws(provided)
⑤ Metal plate of BU-Adapter
⑥ Conduit box(See “Specifications” for details)

Installation Procedures(typical)：

1. Pass all cables through the hole of rubber.

Note: Please identify both sides of the rubber. The side of the rubber with the inclined
angle must be towards the terminals of the cables and metal plate to avoid water
leakage. Refer to the figure below.

2. Insert the rubber into the center hole of metal plate.

3. Then install the metal plate in the conduit box and tighten the screws and finish the
installation.

1

Manufacturer

Part Number

Description

Teddico/BWF

RB-7V

ROUND OUTLET BOX 3/4” GREY 5 HOLE

Teddico/BWF

RB-5V

ROUND OUTLET BOX 1/2” GREY 5 HOLE

Raco

5361-0

4” Round Weatherproof Splice Box 5-1/2”
Outlets

Raco

5372-0

4” Round Weatherproof Splice Box 5-3/4”
Outlets

Orbit

RB50-5

4” ROUND 1/2” THREADED HOLE

OUTDOOR WEATHERPROOF BOX

Orbit

RB75-5

4” ROUND 3/4” THREADED HOLE

OUTDOOR WEATHERPROOF BOX

EGS

WRX50

Round WPRF Box 5-1/2”

EGS

WRX75

Round WPRF Box 5-3/4”

Specifications

Construction Aluminum
Finish Silver liquid painting
Weight 100g

The BU-Adapter can be used with the following conduit boxes:

2

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the
European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures
for recycling this equipment.

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved
defective in material or workmanship for a period of one year after the
date of shipment.

Exceptions to this warranty are as noted below:

• Five years:

– Fiber optic products
– Unshielded Twisted Pair (UTP) transmission products
– CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,

and MC3651H-2X camera models

• Three years:

– FD Series and BU Series analog camera models.
– Fixed network cameras and network dome cameras with Sarix

technology

– Sarix thermal imaging products (TI and ESTI Series)
– Fixed camera models (C20 Series, CCC1390H Series, C10DN

Series, C10CH Series)

– EH1500 Series enclosures
– Spectra
– Spectra HD dome products
– Camclosure

®

IV products (including Spectra IV IP)

®

IS Series integrated camera systems

– DX Series video recorders (except DX9000 Series which is covered

for a period of one year), DVR5100 Series digital video recorders,
Digital Sentry® Series hardware products, DVX Series digital video
recorders, and NVR300 Series network video recorders

– Endura
– Genex

®

Series distributed network-based video products

®

Series products (multiplexers, server, and keyboard)

– PMCL200/300/400 Series LCD monitors
– PMCL5xxF Series and PMCL5xxNB Series LCD monitors

• Two years:

– Standard varifocal, fixed focal, and motorized zoom lenses
– DF5/DF8 Series fixed dome products
– Legacy
– Spectra III

®

Series integrated positioning systems

™

, Spectra Mini, Spectra Mini IP, Esprit®, ExSite®, ExSite

IP, and PS20
scanners, including when used in continuous motion applications

– Esprit Ti and TI2500 Series thermal imaging products
– Esprit and WW5700 Series window wiper (excluding wiper blades)
– CM6700/CM6800/CM9700 Series matrix
– Digital Light Processing (DLP

®

) displays (except lamp and color
wheel). The lamp and color wheel will be covered for a period of 90
days. The air filter is not covered under warranty.

®

• Six months:

– All pan and tilts, scanners, or preset lenses used in continuous

motion applications (preset scan, tour, and auto scan modes)

Pelco will warrant all replacement parts and repairs for 90 days from the
date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to a Pelco designated location. Repairs made necessary
by reason of misuse, alteration, normal wear, or accident are not covered
under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or
loss resulting from the specific use or application made of the Products.

Pelco’s liability for any claim, whether based on breach of contract,

negligence, infringement of any rights of any party or product liability,
relating to the Products shall not exceed the price paid by the Dealer to
Pelco for such Products. In no event will Pelco be liable for any special,
incidental, or consequential damages (including loss of use, loss of profit,
and claims of third parties) however caused, whether by the negligence
of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The
Dealer may also have additional rights, which are subject to variation
from state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800)
289-9100 or [phone] to obtain a Repair Authorization number
(RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, sales order number, or Pelco
invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product that does not fall
under the warranty conditions stated above, please include a written
explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by
which the item was received by Pelco.

RETURNS

To expedite parts returned for repair or credit, please call Pelco at (800)
289-9100 or [phone] to obtain an authorization number (CA
number if returned for credit, and RA number if returned for repair) and
designated return location.

All merchandise returned for credit may be subject to a 20 percent
restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the

assigned CA or RA number and freight should be prepaid.

Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates. © Copyright 2012, Pelco, Inc.
All other product names and services are the property of their respective companies. All rights reserved.
Product specifications and availability are subject to change without notice.

3