Pelco BK4220, BK4024 User Manual

= Vertical bar in left or right margin indicates change or addition.

®

BK4000/BK4024/BK4220 Series

Blower Kit

Installation/Operation

1.0 WARNINGS

Prior to installation and use of this product, the following
WARNINGS should be observed.

1. Installation and servicing should only be done by
Qualified Service Personnel and conform to all
Local codes.

2. Unless the unit is specifically marked as a NEMA
Type 3-6P enclosure, it is designed for Indoor use
only and it must not be installed where exposed to
rain and moisture.

4. Only use replacement parts recommended by
PELCO.

Manual C436M-B (12/94)

2.0 SCOPE

The information contained within this manual covers
the installation and operation of the BK4000/BK4024/
BK4220 Blower Kits. Please familiarize yourself with
the information in this manual prior to installation and
operation.

2.1 DESCRIPTION

The BK4000/BK4024/BK4220 Blower Kits are engi­neered for installation in the EH4014 and EH4018 En­closures. The BK4000 requires 120 VAC, the BK4024
requires 24 VAC, and the BK4220 requires 230 VAC.

All units can be used in conjunction with the corre­sponding Heater Kit.

BK4000 requires 4 watts at 120 VAC, 60 Hz.
BK4024 requires 3 watts at 24 VAC, 60 Hz. (CE)
BK4220 requires 4.8 watts at 230 VAC, 60Hz. (CE)

NOTE: Once installed, the blower kit will reduce
the maximum camera/lens length specified by 1­3/4 inches.

PELCO • 300 W. Pontiac Way, Clovis, CA 93612-5699 • USA • [phone] or (1-559) 292-1981

FAX [phone] or (1-559) 292-3827 • DataFAX [phone] or (1-559) 292-0435

3.0 INSTALLATION

The BK4000/BK4024/BK4220 Blower Kits are sup­plied with the following installation parts:

QTY ITEM

1. Remove the Phillips Head screws from the rear cap
and slide the assembly out from the enclosure.

2. Attach the blower assembly to the rear plate using
two of the self-tapping screws, holding the end
cap to the sled.

1 Blower
1 Blower Bracket

To install the BK4000/BK4024/BK4220 perform the
following steps (refer to Figure 1):

3.1 PARTS LIST (Figure 1.)

Item Qty Description Part Number

1 1 Bracket, fan/pc board BK40004000COMP
2 1 Bracket component, 24VAC, 230VAC BK7044002COMP

1 PCB assy, term/thermott, (used with heater kit) PCB9000300ASSY

3 1 Fan, 2.36-inch Sq., 120/230 VAC MM750010003

1 Fan, 2.36-inch Sq., 24VDC ED210005

4 1 Resistor 3k ohm, 10w (230 VAC blowerkit only) RES003.0K10.0

1 Diode Bridge Rect, 1A400PRV (24 VAC only) DIOMDA104

5 1 Insulator, PC board (heater kit only) BK400010000
A 4 Washer, nylon ZH200X437X62N
B 4 Screw, 6-32 x 3/8 pan phil SS ZH6-32X.375SPP
C 2 Screw, 6-32 x 1.5 pan phil SS ZH6-32X1.50SPP
D 2 Nut, hex, 6-32 ZH6-323NUTSH
E 2 Screw, 6-32 x 1/4 self tapping phil ZH6-SFX.250SPP
F 8 Internal tooth lockwasher, #6 ZH6LWSIS

3. Wire according to the wiring diagram in Figure 2.

NOTE: When used with a heater kit (and
PCB), the blower can be wired into the termi­nal block on the PC Board (see Figure 2). With
the blower kit only, the PCB is not necessary.

Figure 1. Blower Kit Installation

2 PELCO Manual C436M-B (12/94)

4.0 WIRING DIAGRAMS

The following items are supplied in the blower kits.
Refer to Figure 2 for wiring information with the use
of the heater kit PCB board, and without.

Quantity Item PELCO Part No. Blower Kit

1 Fan, 120 VAC, 19 CFM MM750010003 120 & 230 VAC models
1 Fan, 24 VDC, 19 CFM ED210005 24 VAC model
1 Resistor for fan, 3K ohm RES003.0K10.0 230 VAC model
1 Bridge Rectifier Diode DIOMDA104 24 VAC model
1 Capacitor CAPU0050.0/25 24 VAC model
1 Component Bracket BK7044002COMP 24 & 230 VAC models

Thermostat

Heater/Blower wiring
diagrams using
Heater Kit with PCB.

Butt Splices Provided

Fan

1
2
3
4
5
6
7
8
9

10

120 V AC Model

Input, AC High
Input, AC (neutral)
Ground

Fan

Heater

1
2
3
4
5
6
7

Resistor

8
9

10

230 VAC Model

1
2
3
4
5
6

Diode

7
8

Bridge

9

10

24 VAC Model

Input, AC High
Input, AC (neutral)
Ground

Fan

Heater

Heater

+

Fan

_

Input, AC High
Input, AC (neutral)
Ground

Cap

Fan

Heater

Diode Bridge

AC

Cap

24 VAC (BK4024)

230 V AC (BK4220)

Blower Wiring
Installation only.
PCB not required.

120 VAC (BK4000)

Resistor

Fan

Figure 2. Blower Kit Wiring Diagram

PELCO Manual C436M-B (12/94) 3

5.0 WARRANTY AND RETURN
INFORMATION

WARRANTY

PELCO will repair or replace, without charge, any
merchandise proved defective in material or
workmanship for a period of one year after the date of
shipment (six months on all pan and tilts with auto scan
and medium duty scanners, and two years on Legacy®,
Intercept® and CM9500/CM8500 Matrix products).
PELCO will warranty all replacement parts and repairs
for 90 days from the date of shipment. All goods for
warranty work shall be sent freight prepaid to our
Clovis, California facility. Repairs made necessary by
reason of misuse, alteration, normal wear, or accident
are not covered under this warranty. PELCO is not
liable for any incidental or consequential expenses or
liability incurred by the customer as a result of field
repair, installation, or any other reason.

The above warranty is in lieu of any other expressed or
implied warranty, condition, or guarantee by PELCO
of the equipment listed herein. PELCO makes no
warranties except for intended use and will not be liable
for any loss, damage, or costs arising, whether
consequential or incidental, from the use of said
merchandise.

RETURNS

In order to expedite parts returned to the factory for
repair or credit, please call the factory at (800) 289-
9100 or [phone] to obtain an authorization
number (CA number if returned for credit, and RA
number if returned for repair). Goods returned for
repair or credit should be clearly identified with the
assigned CA/RA number and freight should be prepaid.
All merchandise returned for credit may be subject to
a 20% restocking and refurbishing charge.

Ship freight prepaid to: PELCO

300 West Pontiac Way
Clovis, CA 93612-5699

This warranty gives you specific legal rights. You may
also have additional rights, which are subject to variation
from state to state.

If a warranty repair is required, contact PELCO at
[phone] or [phone] for a
Repair Authorization number (RA), and provide the
following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order
number, or PELCO invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product
which does not fall under the warranty conditions
stated above, please include a written explanation with
the product when returned.

Ship freight prepaid to: PELCO

300 West Pontiac Way
Clovis, CA 93612-5699

Method of return shipment shall be the same as method
by which the repair item is received by PELCO.

®

PELCO

300 West Pontiac Way, Clovis, CA 93612-5699

[phone] • [phone]

FAX [phone] or [phone] •

DataFAX [phone] or [phone]

International customers call 1-559-292-1981 or

FAX [phone]

(Product specifications subject to change

without notice.)

C436M-B

4 PELCO Manual C436M-B (12/94)