INSTALLATION
BB5-PCA-BK/BB5-PCA-GY
Pendant Conduit Adapter
C1482M-A (1/06)
Important Safety Instructions
Prior to installation and use of this product, the following WARNINGS should be observed.
1. Installation and servicing should only be done by qualified service and installation personnel.
2. Installation shall be done in accordance with all local and national electrical and mechanical codes utilizing only approved materials.
3. Use only installation methods and materials capable of supporting four (4) times the maximum
specified load.
4. Use stainless steel hardware to fasten the mount to outdoor surfaces.
5. To prevent damage from water leakage when installing a mount outdoors on a roof or wall, apply sealant around the bolt holes between the mount and mounting surface.
Please thoroughly familiarize yourself with the information in this manual prior to installation and
operation.
This equipment contains electrical or electronic components that must be recycled properly to
comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical
and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this
equipment.
C1482M-A (1/06) 3
Description
The BB5-PCA Pendant Conduit Adapter is used when installing an SD5 Series Spectra® or a
DF5 Series discreet pendant dome to a hard ceiling in locations such as a parking garage having
surface-mounted conduit. The top of the Spectra back box mates directly to the adapter using the
three mounting holes that currently exist. A self-adhesive gasket, three 8-32 nuts, and three lock
washers are provided with each adapter. The adapter is designed to accept 1/2-inch (1.27 cm)
diameter conduit.
NOTE:
The BB5-PCA pendant conduit adapter should not be used with the Heavy-Duty Spectra III™
Series, Stainless Steel Spectra III Series, or Pressurized Spectra III Series.
MODELS
BB5-PCA-BK Pendant conduit adapter, black
BB5-PCA-GY Pendant conduit adapter, gray
4 C1482M-A (1/06)
Installation
NOTE:
To make the top opening of the adapter waterproof, remove one plug from a side opening and
screw it into the top and/or apply sealant around the top opening on the adapter mating surface prior
to installation.
To install the adapter (refer to Figure 1):
1. Attach the adapter to the hard surface with fasteners (not supplied) that are sufficient to
support 40.0 lb (18.14 kg).
2. Remove the 3/4-inch (1.91 cm) threaded plug from the adapter for the conduit opening that will be used (if not previously removed).
3. Pull the wires through the conduit opening and attach the conduit to the adapter.
SD5 Spectra Only:
4.
a. Unscrew the thumbscrew that attaches the interconnect door to the interconnect back
box receptacle and open the door. The door is hinged to the interconnect back box.
WARNING:
interconnect circuit board and components when handling them.
The interconnect door has a circuit board attached. Take care not to damage the
b. Remove the three nuts and washers that attach the interconnect back box assembly to
the back box and remove the assembly. For best results, the interconnect door should be
opened to the 90° position. Retain the nuts and washers for reinstallation.
5. Remove the three screws, lock washers, and flat washers that attach the top mount, gasket,
and leash to the back box. Discard the top mount, gasket, screws, and washers. Retain the
leash for reinstallation.
6. Remove the protective covering from the new gasket (provided) and stick the new gasket on the adapter. Position the back box on the adapter with the adapter studs through the three holes in the back box.
7. Attach the back box to the adapter with three 8-32 nuts and lock washers (provided). Reattach the leash to any one of the studs.
SD5 Spectra Only:
8.
nuts and washers. The interconnect door should be opened to the 90° position during
reinstallation.
9. Refer to the applicable dome installation/operation manual to complete the dome installation.
NOTE:
In order to make the installation weather tight, put a bead of silicone sealant around the seam
of the adapter and the back box after completion.
Reinstall the interconnect back box assembly on the back box with three
Specifications
Construction Aluminum
Finish Polyester powder coat
Dimensions 4.2" L x 4.2" W x 1.8" H
(10.67 cm 10.67 cm x 4.52 cm)
Rating Meets NEMA Type 4 standards
C1482M-A (1/06) 5
A
B
C
D
M
L
K
P
E
Figure 1.
G
P
F
I
H
BB5-PCA Adapter Installation
Table A.
N
O
J
DF5SD5
Part List
Item Qty Description
A 1 Adapter
B 1 Gasket (New)
C 3 Lock Washer
D 3 Nut, 8-32
E 1 Thumbscrew (SD5 Spectra)
F 1 Interconnect Door (SD5 Spectra)
G 1 Interconnect Back Box (SD5 Spectra)
H 3 Nut
I 3 Washer
J 1 Back Box
K 4 Screw
L 3 Lock Washer
M 3 Flat Washer
N 1 Top Mount
O 1 Gasket (Old)
P 1 Leash
L
K
C
D
BB5-PCA
Adapter Parts
SD5 and/or DF5
Parts
M
6 C1482M-A (1/06)
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship
shipment.
Exceptions to this warranty are as noted below:
• Five years on FT/FR8000 Series fiber optic products.
• Three years on Genex
• Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and
MC3651H-2X camera models, which have a five-year warranty.
• Three years on PMCL 200/300/400 Series LCD monitors.
• Two years on standard motorized or fixed focal length lenses.
• Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.
• Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in continuous motion applications.
• Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
• Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays. The lamp and color wheel will be covered for a period of
90 days. The air filter is not covered under warranty.
• Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, Endura™ Series distributed network-based video
products, and TW3000 Series twisted pair transmission products.
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight
prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this
warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products
shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state
to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and
provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written
explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.
®
Series products (multiplexers, server, and keyboard).
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization
number (CA number if returned for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate
address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the
following
:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
REVISION HISTORY
Manual # Date Comments
C1482M 4/98 Original version.
C1482M-A 1/06 Updated to new format. Inserted compatability note.
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. ©Copyright 2006, Pelco.
Endura, ExSite, and Spectra III are trademarks of Pelco. All rights reserved.
DLP is a registered trademark of Texas Instruments, Inc.
for a period of one year
after the date of
Worldwide Headquarters
3500 Pelco Way
Clovis, California 93612 USA
USA & Canada
Tel: 800/289-9100
Fax: 800/289-9150
International
Tel: 1-559/292-1981
Fax: 1-559/348-1120
www.pelco.com
ISO9001
United States
|
Canada
United Kingdom
|
The Netherlands
|
Singapore
|
|
Spain
Scandinavia
|
|
France
Middle East
|
Loading...