Pelco BB5HD User Manual

00546

BB5HD Series

Heavy-Duty Spectra

Back Box

Installation Manual

C2429M (3/01)

®

Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com

In North America and Canada: Tel [phone] • FAX [phone]

International Customers: Tel [phone] • FAX [phone]

CONTENTS

IMPORTANT SAFEGUARDS AND WARNINGS ......................................................................................................... 3

DESCRIPTION ................................................................................................................................................................... 4

MODELS ........................................................................................................................................................................ 4

UNPACKING INSTRUCTIONS ........................................................................................................................................4

INSTALLATION IN-CEILING MODELS ......................................................................................................................... 5

STEP 1 - PREPARE CEILING ....................................................................................................................................5

STEP 3 - INSTALL THE BACK BOX...........................................................................................................................5

STEP 2 - INSTALL THE MOUNTING PLATES .......................................................................................................... 5

STEP 5 - INSTALL DOME DRIVE ............................................................................................................................. 6

STEP 4 - WIRE CIRCUIT BOARD ............................................................................................................................. 6

STEP 6 - INSTALL LOWER DOME ........................................................................................................................... 6

INSTALLATION PENDANT MODELS .......................................................................................................................... 7

STEP 1 - MOUNT AND INSTALL THE BACK BOX ................................................................................................... 7

STEP 2 - WIRE CIRCUIT BOARD ............................................................................................................................. 7

STEP 3 - INSTALL DOME DRIVE ............................................................................................................................. 8

STEP 4 - INSTALL LOWER DOME ........................................................................................................................... 8

TROUBLESHOOTING ...................................................................................................................................................... 9

APPENDIX ......................................................................................................................................................................... 10

SPECIFICATIONS ............................................................................................................................................................. 14

WARRANTY AND RETURN INFORMATION .............................................................................................................. 16

LIST OF ILLUSTRATIONS

Figure 1. Dimension Drawing .................................................................................................................................................15

LIST OF TABLES

Ta ble A. Video Coaxial Cable Wiring Distances .................................................................................................................... 10

Ta ble B. 24 VAC Wiring Distances ........................................................................................................................................ 10

Ta ble C. Switch Settings for SW1 ..........................................................................................................................................10

Ta ble D. Switch Settings for SW2 – P-Type Control .............................................................................................................. 11

Ta ble E. Switch Settings for SW2 – D-Type Control .............................................................................................................. 11

Pelco Installation Manual C2429M (3/01) 2

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.

Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must

2.

not be installed where exposed to rain and moisture.

3. Only use replacement parts recommended by Pelco.

4. After replacement/repair of this unit’s electrical components, conduct a resistance measurement between line and exposed parts to
verify the exposed parts have not been connected to line circuitry.

5. The installation method and materials should be capable of supporting four times the weight of the enclosure, pan/tilt, camera and
lens combination.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.

This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.

Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

Pelco Installation Manual C2429M (3/01) 3

DESCRIPTION

The Heavy-duty Spectra is perfect for installations where structural integrity and vandalism are a priority. The system features barrel
key locks, heavy-duty construction and a thick acrylic lower dome. The in-ceiling model has a reinforced bracket mounting system for
installation in a fixed ceiling. Pendant models can be mounted to a pole or wall using the IWM Spectra wall mount.

MODELS

BB5HD-F In-ceiling back box with reinforced bracket-mounting system
BB5HD-PG Indoor, pendant style back box with reinforced sun shroud
BB5HD-PG-E Environmental, pendant style back box with heater, fan and reinforced sun shroud

Lower dome models are not interchangeable. Each heavy-duty lower dome is designed for a specific back box model. Install the
correct lower dome to the right back box. See the following chart.

Back Box Model Lower Dome Model Lower Dome with Cage Model

BB5HD-F LD5HDF-1 LD5HDCF-1

BB5HD-PG LD5HDPG-1 LD5HDCPG-1

BB5HD-PG-E LD5HDPG-E1 LD5HDCPG-E1

Spectra Lite and all Spectra II model dome drives are compatible with all Heavy-Duty back box models.

UNPACKING INSTRUCTIONS

If an item needs to be returned to the factory, consult the WARRANTY AND RETURN section of this manual for instructions.

The following items are supplied:

IN-CEILING MODELS

1 Back box
1 Mounting plate
2 Back mounting plates
1 Parts bag

2 8-32 x .275-inch screws
1 Conduit fitting
1 Safety chain bracket
1 Lock nut
1 Compass tool

PENDANT MODELS

1 Back box
1Tube of thread compound

Pelco Installation Manual C2429M (3/01) 4

INSTALLATION IN-CEILING MODEL

SPRING CLIP

8-32X.275 INCH SCREW

00537

00535

STEP 1 - PREPARE CEILING

00530

00531

a. Locate the center point of the mount-

ing location. Drill a hole in the ceiling
using a 3/32-inch drill.

b. Insert the compass tool into the hole.

Draw a circle on the ceiling using the
compass tool and a pencil. Cut the
circle out of the ceiling.

STEP 2 - INSTALL THE MOUNTING PLATES

Use the eight 10-32 x 3-inch screws (supplied) and install the mounting ring and
two back mounting plates.

a. Line up the mount ring with the eight

fastener holes.

b. Feed one back mounting plate through

c. Install fasteners through the mount ring,

ceiling and out the back mounting plate.

d. Install second back mounting plate.
the hole in the ceiling and line up with
four fastener holes.

STEP 3 - INSTALL THE BACK BOX

ATTA CH SA FETY CHAIN HERE

c. Use the mounting ring as a template

and mark the hole pattern onto the
mounting surface. Prepare the holes.

S

MOUNTING
RING

00532

CEILING

00533

00534

a. Attach the conduit fitting, lock nut, and

safety chain bracket. Install a safety
chain/cable (not supplied) that will
support up to 16 pounds (7.3 kg).

b. Turn the thumbscrew and open the

hinged door to the back box. Pull wiring
into the back box through the conduit
fitting. Refer to Tables A and B in the
Appendix for wiring distances.

c. Compress the spring clips on the back

box and push it through the hole, until
the clips spring back.Tighten the screws
until you hear a clicking noise. Insert the
two 8-32 x .275-inch screws to secure
the back box to the mount ring.

Pelco Installation Manual C2429M (3/01) 5