INSTALLATION
INSTALLATION
ExSite™ Series Mounts
WXM100, CMXM100, PAXM100,
PXM200, and AXM100 Models
C2216M (5/05)
Important Safety Instructions
CAUTION:
RISK OF ELECTRIC
SHOCK.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Only use attachments/accessories specified by the manufacturer.
6. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
7. Installation should be done only by qualified personnel and conform to all local codes.
8. Use only installation methods and materials capable of supporting four times the maximum specified load.
9. Use stainless steel hardware to fasten the mount to outdoor surfaces.
CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any
servicing other that contained in the operating instructions unless you are qualified to do so.
10. Only use replacement parts recommended by Pelco.
The product and/or manual may bear the following marks:
WARNING: This symbol indicates that dangerous voltage constituting a
risk of electric shock is present within this unit.
This symbol indicates that there are important operating and maintenance
instructions in the literature accompanying this unit.
3 C2216M (5/05)
Description
This manual contains the installation instructions for the following ExSite™ Series mounts:
WXM100 Wall mount designed to mount the ExSite
CMXM100 Corner adapter for use with the WXM100 to mount an ExSite Series system to the corner of a structure.
PAXM100 Pole adapter for use with the WXM100 to mount a system to a horizontal pole.
PXM200 Pedestal mount designed to mount an ExSite Enhanced Series system directly to a horizontal surface in either an upright or
AXM100 Adjustable mount for ExSite Enhanced Fixed models allowing manual pan/tilt adjustment..
inverted position
Series system directly to a load-bearing vertical surface.
Model Supplied Hardware
WXM100 /
PXM200
CMXM100
PAXM100
AXM100
None
Five 3/8-16 x 1.0-inch
thread length,
stainless steel hex
head bolts with lock
washers to attach the
adapter to the
WXM100 wall mount
Four 5/8-inch wide x
40-inch (101.6 cm) long
stainless steel straps
to attach the adapter
to a pole
Five 3/8-16 x 1.0-inch
thread length,
stainless steel hex
head bolts with lock
washers to attach the
adapter to the
WXM100 wall mount
Mounting
Surface
Solid Concrete*
Steel I Beam**
Solid Concrete*
Steel I Beam**
Steel pole with a
diameter between
4 and 9 inches
(10.16 to 22.86 cm)
Recommended Hardware
Five 3/8-16 x 1-9/16-inch long stainless steel drop-in anchors and five 3/8-16 x
1.0-inch thread length, stainless steel hex head bolts with stainless steel lock washers
Five 3/8-16 x 1.0-inch thread length, stainless steel hex head bolts with stainless
steel lock washers and 3/8-16 stainless steel nuts
Six 1/2-13 x 2-inch stainless steel drop-in anchors and six 1/2-13 x 1.0-inch thread
length, stainless steel hex head bolts with stainless steel lock washers
Six 1/2-13 x 1.0-inch thread length, stainless steel hex head bolts with stainless
steel lock washers and 1/2-13 stainless steel nuts
Supplied
*Recommended strength of concrete is 3,600 psi or 25 Mpa.
**Minimum of 1/8-inch wall.
C2216M (5/05) 4
Loading...