Peerless-AV SC550GL Installation

Installation and Assembly: Flat Panel Display Cart
Models: SC590, SC590-S
ACC964
(sold separately)
Max Load Capacity: 300 lb (136.1 kg)
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com
ISSUED: 08-08-12 SHEET #: 009-9074-1
NOTE: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact your local distributor.
• This product should only be installed by someone of good mechanical aptitude, and fully understands these instructions.
• Never exceed the Maximum Load Capacity on page 1.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws fi rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power.
• The cart is not affi xed or secured to the fl oor, and may therefore tip over and/or fall if display and/or cart is shaken or hit. Always monitor children and do not let children play alone around cart as they could get hurt by a falling display. Not recommended for use in areas with heavy traffi c.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.
Tools Needed for Assembly
• phillips screwdriver
Table of Contents
Parts List............................................................................................................................................................................ 3, 4
Assembling Cart .....................................................................................................................................................................5
Installing Vertical Adapters to Flat Panel Display ...................................................................................................................9
Mounting Flat Panel Display .................................................................................................................................................11
2 of 12
A
V
W
Before you begin, make sure all parts shown are included with your product.
Parts List
Description Qty. Part Number Part Number
mount bracket 2 201-1156 201-G4156 hook plate 2 201-1157 201-G4157
B
M10 x .402 ID lock washer 6 540-9424 540-9424
C
base 1 009-1437 009-G4437
D
universal plate 1 009-1432 009-G4432
E
adapter bracket 2 201-1513 201-G4513
F
upright 2 580-1180 580-G4180
G
top cover 2 590-1210 590-4210
H
1/4-20 x 12mm decorative screw 20 520-2325 520-1325
I
1/4-20mm nut 12 530-1050 530-2031
J
M10 x 15 mm socket screw 8 520-9262 520-9534
K
3/8-16 x 2.5" socket screw 6 520-9550 520-9550
L
7/32" allen wrench 1 560-9715 560-9715
M
6 mm allen wrench 1 560-9716 560-9716
N
4 mm allen wrench 1 560-9646 560-9646
Q
right leg 1 009-1295 009-G4295
R
left leg 1 009-1296 009-G4296
S
wheel caster 2 600-0044 600-0044
T
wheel caster/brake 2 600-0045 600-0045
U
joint connector nut 4 530-1037 530-2037 3/8-16 x 1.5" screw bolt 4 520-1329 520-1329 3/16" allen wrench 1 560-0071 560-0071
X
SC590 SC590-S
Parts may appear slightly different than illustrated.
A
B
DE
C
H
F
G
3 of 12
Parts List continued
Parts may appear slightly different than illustrated.
R
J
KI
L
M
NQ
UT
V
W
S
M4 x 12mm (6)
(510-1079)
M6 x 20mm (4)
(520-9554)
M8 x 15mm (6)
(520-1068)
Security Tilt Bracket Fasteners
M4 x 25mm (4)
(510-1082)
M6 x 25mm (4)
(520-1211)
M8 x 25mm (4)
(520-1101)
M5 x 12mm (4)
(520-1064)
M5 x 25mm (4)
(520-1122)
M6 x 30mm (4)
(520-1067)
M8 x 40mm (4)
(520-1152)
X
M6 x 12mm (4)
(520-1050)
.75" spacer
(540-1059) (4)
.5" spacer
(540-1057) (4)
multi-washer (6)
(580-1036)
4 of 12
Insert right leg (R) into base housing (D) as shown in fi g. 1.1. Then align holes in right leg with holes in base
1
housing (D). Fasten base housing to right leg using two 3/8-16 x 1.5" bolts (W) and two joint connectors (V).
NOTE: Left and right legs can be identi ed by looking at the cart from the front.
Repeat for left side with left leg (S).
g. 1.1fi g. 1.1 fi g. 1.2
S
V
D
FRONT OF CART
FRONT OF LEG
Insert casters (U & T) into holes of support legs (R & S) and hand thread to secure. Attach casters with brake (U) to
2
the back of left and right support legs (R & S). Attach casters without brake (T) to front of support legs as shown.
NOTE: Lock brakes on casters to avoid sudden movements during installation.
R
W
R
S
R
T
HAND THREAD
U
5 of 12
HOLD WHEEL
Attach uprights (G) to base (D), as shown below using six 3/8-16 x 2.5" socket screws (L) and M10 x .402ID lock
3
washers (C). Tighten all screws.
g. 3.1
G
D
C
L
Loosely attach six 1/4-20 x 12 mm screws (I) and
4
1/4-20 nuts (J) to mount bracket (A).
Repeat with second mount bracket (A)
I
A
J
Slide mount bracket (A) onto upright (G) so that 1/4-
5
20 nuts (J) slide into slots of upright (G) as shown in gure 5.1 and detail 1. Slide display mount bracket to desired position, level, then tighten 1/4-20 x 12 mm screws (I) using 4 mm allen wrench (Q). Repeat with second mount bracket (A).
NOTE: Make sure that two mount brackets (A) are level.
A
J
I
G
DETAIL 1
G
6 of 12
SLOT
g. 5.1
Snap top cover (H) onto upright (G).
6
Insert two 1/4-20 x 12 mm screws (I) into mount
7
bracket (A), leaving 3/16" of exposed thread as shown in fi gure 7.1 and detail 2.
H
G
g. 7.1
I
A
3/16"
DETAIL 2
Attaching Universal Adapter Plate
Attach one universal plate (E) to two hook plates
8
(B) using eight M10 x 15 mm socket screws (K). Tighten screws using 6 mm allen wrench (N).
E
B
K
Attach hook plate (B) to mount bracket (A).
9
A
B
7 of 12
Insert two 1/4-20 x 12 mm screws (I) into holes indicated below for desired display orientation. Tighten all screws
10
using 4 mm allen wrench (Q).
I
I
I
2° Backward Tilt 5° Forward TiltNo Tilt
8 of 12
Installing Adapter Brackets
WARNING
• Tighten screws so adapter brackets are fi rmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to display or product may fail.
To prevent scratching the display, set a cloth on a fl at, level surface that will support the weight of the display.
11
Place display face side down. If display has knobs on the back, remove them to allow the adapter brackets to be attached. Place adapter brackets (F) on back of display, align to holes, and center on back of display as shown below. Attach the adapter brackets to the back of the display using the appropriate combination of screws, multi­washers, and spacers as shown in fi gure 11.1 or 11.2.
NOTE: Top and bottom holes on display must always be used. Verify that all holes are properly aligned, and then tighten screws using a phillips screwdriver.
X
MULTI-WASHER
CENTER BRACKETS VERTICALL Y
ON BACK OF DISPLAY
F
NOTE: "X" dimensions should be equal.
MEDIUM HOLE FOR M5 SCREWS
SMALL HOLE FOR M4 SCREWS
LARGE HOLE FOR M6 SCREWS
X
Notes:
• The number of fasteners used will vary, depending upon the type of display.
• Multi-washers and spacers may not be used, depending upon the type of display.
• Use the corresponding hole in the multi­washer that matches your screw size as shown.
NOTE: For fl at back displays proceed to step 11-1. For bump-out or recessed back display skip to step 11-2.
9 of 12
For Flat Back Display
11-1
Begin with the shortest length screw, hand thread through multi-washer and adapter bracket (F) into display as shown below. Screw must make at least three full turns into the mounting hole and fi t snug into place. Do not over tighten. If screw cannot make three full turns into the display, select a longer length screw from the baffl ed fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
NOTE: Spacers may not be used, depending upon the type of display.
DISPLAY
If you have any questions, please call Peerless customer care at 1-800-865-2112.
For Bump-out or Recessed Back Display
11-2
Begin with longer length screw, hand thread through multi-washer, adapter bracket (F) and spacer in that order into display as shown below. Screw must make at least three full turns into the mounting hole and fi t snug into place. Do not over tighten. If screw cannot make three full turns into the display, select a longer length screw from the baffl ed fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
g 11.1
MULTI-WASHER
SCREW
ADAPTER BRACKET (F)
DISPLAY
g 11.2
SPACER
If you have any questions, please call Peerless customer care at 1-800-865-2112.
10 of 12
MULTI-WASHER
SCREW
ADAPTER BRACKET (F)
Mounting and Removing Flat Panel Display
WARNING
• Always use an assistant or mechanical lifting equipment to safely lift and position the fl at panel display.
Hook adapter brackets (F) onto universal plate (E),
12
then slowly swing display in as shown. Turn safety screws, using security allen wrench (Q), clockwise at least six times to prevent display from being removed as shown in detail 3.
NOTE: To lock the display down, tighten safety screws to wall plate as shown in cross section.
To remove display from mount, loosen safety screws, swing display away from mount, and lift display off of mount.
E
SAFETY
SCREWS
E
F
DETAIL 3
CAUTION
• Do not tighten screws with excessive force. Overtightening can cause damage to mount. Tighten screws to 40 in. • lb (4.5 N.M.) maximum torque.
F
11 of 12
All other brand and product names are trademarks or registered trademarks of their respective owners.
© 2012, Peerless Industries, Inc. All rights reserved.
Peerless Industries, Inc.
2300 White Oak Circle
www.peerlessmounts.com
Aurora, Il 60502
LIMITED FIVE-YEAR WARRANTY
Peerless Industries, Inc. (“Peerless”) warrants to original end-users of Peerless® products will be free from defects in material and workmanship, under normal
use, for a period of fi ve years from the date of purchase by the original end-user (but in no case longer than six years after the date of the product’s manufacture).
In no event shall the duration of any implied warranty of merchantability or fi tness for a particular purpose be longer than the period of the applicable
express warranty set forth above. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty does not cover damage caused by (a) service or repairs by the customer or a person who is not authorized for such service or repairs by Peerless,
(b) the failure to utilize proper packing when returning the product, (c) incorrect installation or the failure to follow Peerless’ instructions or warnings when installing,
In no event shall Peerless be liable for incidental or consequential damages or damages arising from the theft of any product, whether or not secured
by a security device which may be included with the Peerless® product. Some states do not allow the exclusion or limitation of incidental or consequential
This warranty is in lieu of all other warranties, expressed or implied, and is the sole remedy with respect to product defects. No dealer, distributor, installer or other
person is authorized to modify or extend this Limited Warranty or impose any obligation on Peerless in connection with the sale of any Peerless® product.
At its option, Peerless will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.
using or storing the product, or (d) misuse or accident, in transit or otherwise, including in cases of third party actions and force majeure.
damages, so the above limitation or exclusion may not apply to you.
This warranty gives specifi c legal rights, and you may also have other rights which vary from state to state.
www.peerless-av.com
© 2012 Peerless Industries, Inc.
12 of 12
Loading...