How it Works
Peerless-AV
Loading...
SC550
Installation
11 pgs937.54 Kb0
Specsheet
2 pgs292.6 Kb0

Peerless-AV SC550 Installation

Download
Installation and Assembly:
32" - 65" (81 - 165 cm) Kiosk Cart
Models: SC560FK
Max UL Load Capacity:
150 lb (68 kg) display
15 lb (6.8 kg) component
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.com
ISSUED: 09-30-11 SHEET #: 009-9057-3 05-23-12
NOTE: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact your local distributor.
• This product should only be installed by someone of good mechanical aptitude, and fully understands these instructions.
• Never exceed the Maximum UL Load Capacity on page 1.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws fi rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power.
• The cart is not affi xed or secured to the fl oor, and may therefore tip over and/or fall if display and/or cart is shaken or hit. Always monitor children and do not let children play alone around cart as they could get hurt by a falling display. Not recommended for use in areas with heavy traffi c.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.
Tools Needed for Assembly
• phillips screwdriver
Table of Contents
Parts List............................................................................................................................................................................ 3, 4
Assembling Cart .....................................................................................................................................................................5
Installing Adapter Brackets to Flat Panel Display ...................................................................................................................8
Mounting Flat Panel Display ................................................................................................................................................ 10
Cable Management .............................................................................................................................................................10
ISSUED: 09-30-11 SHEET #: 009-9057-3 05-23-12
Before you begin, make sure all parts shown are included with your product.
A
V
X
Y
Parts List
Description Qty. Part Number
base 1 009-1223 column 1 009-1427
B
column bracket 1 009-1424
C
tilt plate 1 009-1423
D
adapter plate 1 201-1110
E
adapter bracket 2 201-1510
F
3/8-16 x 1" button socket cap screw 3 520-1354
G
3/8-16 x 1-1/2" button socket cap screw 4 520-1329
H
5/16-18 x 3/8" button socket cap screw 4 520-1693
I
M10 lock washer 3 540-9424
J
M10 x 15 mm button socket cap screw 4 520-9262
K
3/8-16 X 2-1/2" button socket cap screw 3 520-9550
L
6 mm allen wrench 1 560-9716
M
7/32" allen wrench 1 560-9715
N
right leg 1 009-1295
O
left leg 1 009-1296
P
caster 2 600-0044
Q
caster with brake 2 600-0045
R
joint connector 4 530-1037
S
3/16" allen wrench 1 560-0071
T
top plate 1 201-1724
U
bottom plate 1 201-1699 rubber feet (pack of four) 1 570-1036
W
M8 x 15mm socket pin screw 4 520-1068 M10 x 15mm penta-pin screw 4 520-9263 M10 penta-pin tool 1 520-9260
Z
4mm allen wrench 1
AA
Parts may appear slightly different than illustrated.
560-9646
F
A
B
C
D
K
P
L
E
M
Q
G
H
I
J
N
SR
T
O
ISSUED: 09-30-11 SHEET #: 009-9057-3 05-23-12
U
V
WXY
Z
Security Adapter Bracket Fasteners
AA
M5 x 12mm (4)
(520-1064)
M5 x 25mm (4)
(520-1122)
M6 x 12mm (4)
(520-1050)
M6 x 25mm (4)
(520-1211)
M8 x 12mm (4)
(520-1724)
M8 x 25mm (4)
(520-1101)
.75" spacer (4)
(540-1059)
Multi-washer (4)
(580-1398)
ISSUED: 09-30-11 SHEET #: 009-9057-3 05-23-12
Insert right leg (O) into base (A) as shown in fi gure 1.1. Then line up holes of right leg with holes in base. Fasten
1
right leg to base using two 3/8-16 x 1-1/2" button socket cap screws (H) and two joint connectors (S), tighten using 3/16" allen wrench (T) and 7/32" allen wrench (N) as shown in fi gure 1.2.
NOTE: Left and right legs can be identifi ed by looking at the cart from the front. Repeat for left side of column base with left leg (P).
fi g. 1.1
fi g. 1.2
A
O
FRONT OF CART
FRONT OF LEG
Insert casters (Q, R) into holes of support legs (O, P) and hand thread to secure. Attach casters with brake (R) to
2
rear of support legs (O, P). Attach casters without brake (Q) to front of support legs (O, P) as shown. NOTE: Lock brakes on casters to restrict movement during installation.
S
H
O
P
HAND THREAD
O
HOLD WHEEL
Q
R
ISSUED: 09-30-11 SHEET #: 009-9057-3 05-23-12
Attach column (B) to base (A) with three
3
3/8-16 x 2-1/2" button socket cap screws (L) and three M10 lock washers (J). Tighten screws using 7/32" allen wrench (N).
A
J
L
B
Attach the column bracket (C) to column (B) with
4
three 3/8-16 x 1" button socket cap screws (G). Tighten screws using 7/32" allen wrench (N).
G
C
B
Attach tilt plate (D) to bottom plate (V) with four
5
M10 x 15 mm button socket cap screws (K). Tighten screws using 6 mm allen wrench (M).
V
D
K
Attach tilt plate (D) to column bracket (C) with four
6
5/16-18 x 3/8" button socket cap screws (I) as shown in rear view.
Tilt can be adjusted to 0° or 30°.
I
C
D
REAR VIEW
ISSUED: 09-30-11 SHEET #: 009-9057-3 05-23-12
Attach top plate (U) to adapter plate (E) with four
7 8
M10 x 15 mm penta-pin screws (Y). Tighten screws using penta-pin tool (Z).
E
Secure four rubber feet (W) to bottom of CPU as shown below.
CPU
U
Z
Secure CPU to top plate (U) using safety belt.
8-1
NOTE: Safety belt may need to be loosened to attach CPU to component box top plate.
U
CPU
CPU MAY APPEAR DIFFERENT THAN
ILLUSTRATED
W
Secure top plate (U) to bottom plate (V) with four M8
9
x 15 mm screws (X) as shown in rear view. Tighten screws using 4 mm allen wrench (AA).
U
SAFETY BELT
X
V
REAR VIEW
ISSUED: 09-30-11 SHEET #: 009-9057-3 05-23-12
Installing Adapter Brackets to Flat Panel Display
WARNING
• Tighten screws so adapter brackets are fi rmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the display inserts or if screws bottom out and adapter brackets are still not tightly secured, damage may oXur to display or product may fail.
To prevent scratching the display, set a cloth on a fl at, level surface that will support the weight of the display. Place
10
display face side down. Refer to display manufacturers instructions or customer service, for removing any knobs, base, cover, or screw(s) on the back of the display to prepare mounting. These need to be removed to allow the adapter brackets (F) to be attached. Select the small, medium, large or extra large screws from the baffl ed fastener pack then attach adapter brackets to display following fi gure 10.1 or 10.2.
NOTE: Top and bottom mounting holes must be used for attaching adapter brackets. Verify that all holes are properly aligned, and then tighten screws using 4 mm security allen wrench (AA).
X
F
NOTE: "X" dimensions should be equal.
Notes:
• The number of fasteners used will vary, depending upon the type of display.
• Multi-washers and spacers may not be used, depending upon the type of display.
• Use the corresponding hole in the multi- washer that matches your screw size as shown.
CENTER BRACKETS
VERTICALLY ON BACK
OF DISPLAY
X
MULTI-WASHER
MEDIUM HOLE FOR M5 SCREWS
SMALL HOLE FOR M4 SCREWS
LARGE HOLE FOR M6 SCREWS
NOTE: For fl at back displays proceed to step 10-1. For bump-out or recessed back display skip to step 10-2
ISSUED: 09-30-11 SHEET #: 009-9057-3 05-23-12
For Flat Back Display
10-1
Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into display as shown below. Screw must make at least three full turns into the mounting hole and fi t snug into place. Do not over tighten. If screw cannot make three full turns into the display, select a longer length screw from the baffl ed fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
NOTE: Spacers may not be used, depending upon the type of display.
If you have any questions, please call Peerless customer care at 1-800-865-2112.
fi g. 10.1
DISPLAY
MULTI-WASHER
SCREW
ADAPTER
BRACKET (F)
For Bump-out or Recessed Back Display
10-2
Begin with longer length screw, hand thread through multi-washer, adapter bracket and spacer in that order into display as shown below. Screw must make at least three full turns into the mounting hole and fi t snug into place. Do not over tighten. If screw cannot make three full turns into the display, select a longer length screw from the baffl ed fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
DISPLAY
SPACER
If you have any questions, please call Peerless customer care at 1-800-865-2112.
fi g. 10.2
MULTI-WASHER
SCREW
ADAPTER
BRACKET (F)
ISSUED: 09-30-11 SHEET #: 009-9057-3 05-23-12
Mounting Flat Panel Display
Cable Management
Hook adapter brackets (F) onto adapter plate (E).
11
Then slowly swing display down as shown. Turn safety/security screws, using 4 mm security allen wrench (AA), clockwise at least six times to prevent display from being removed as shown in detail 1 of fi gure 1 1.1.
NOTE: To lock the display down, tighten security screws to adapter plate (E) as shown in detail 1.
fi g 11.1
Run cables through column (B) using cable
12
management holes.
CABLE MANAGEMENT HOLES
B
F
DETAIL 1
E
SECURITY SCREWS
10 of 11
All other brand and product names are trademarks or registered trademarks of their respective owners.
ISSUED: 09-30-11 SHEET #: 009-9057-3 05-23-12
© 2012, Peerless Industries, Inc. All rights reserved.
Peerless Industries, Inc.
2300 White Oak Circle
www.peerlessmounts.com
Aurora, Il 60502
LIMITED FIVE-YEAR WARRANTY
Peerless Industries, Inc. (“Peerless”) warrants to original end-users of Peerless® products will be free from defects in material and workmanship, under normal
use, for a period of fi ve years from the date of purchase by the original end-user (but in no case longer than six years after the date of the product’s manufacture).
In no event shall the duration of any implied warranty of merchantability or fi tness for a particular purpose be longer than the period of the applicable
express warranty set forth above. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty does not cover damage caused by (a) service or repairs by the customer or a person who is not authorized for such service or repairs by Peerless,
(b) the failure to utilize proper packing when returning the product, (c) incorrect installation or the failure to follow Peerless’ instructions or warnings when installing,
In no event shall Peerless be liable for incidental or consequential damages or damages arising from the theft of any product, whether or not secured
by a security device which may be included with the Peerless® product. Some states do not allow the exclusion or limitation of incidental or consequential
This warranty is in lieu of all other warranties, expressed or implied, and is the sole remedy with respect to product defects. No dealer, distributor, installer or other
person is authorized to modify or extend this Limited Warranty or impose any obligation on Peerless in connection with the sale of any Peerless® product.
At its option, Peerless will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.
using or storing the product, or (d) misuse or aXident, in transit or otherwise, including in cases of third party actions and force majeure.
damages, so the above limitation or exclusion may not apply to you.
This warranty gives specifi c legal rights, and you may also have other rights which vary from state to state.
www.peerlessmounts.com
© 2012 Peerless Industries, Inc.
11 of 11
ISSUED: 09-30-11 SHEET #: 009-9057-3 05-23-12
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use