PEERLESS FPE42FH-S, FPE42F-B, FPE42F-S Installation And Assembly Manual
Installation and Assembly:
Peerless Environmental Enclosure for 42" Flat Panel Screens
Model: FPE42F-S, FPE42FH-S, FPE42F-B
2300 White Oak Circle • Aurora, IL 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.com
Max Load Capacity: 250 lb (113 kg)
ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11
NOTE: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• Due to outdoor environmental conditions such as strong wind gusts, heavy snow, hail, rain, etc. The environmental
enclosure and hardware, must be inspected at least once a year, and immediately following any time winds exceed
90 mph. A qualifi ed installer or inspector must check for signs of rust, loose fasteners, bent metal, etc. If evidence
of excessive wear, deterioration or any unsafe condition is observed, this product must be taken out of service
immediately. Direct all inquiries to customer care if you have any questions.
• Glass face of enclosure must avoid direct sunlight or damage to display may occur.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum Load Capacity. See page one.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of
an "edge to edge" stud fi nder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws fi rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product was designed for use with other outdoor products only
• This product was designed to be installed on the following wall construction only;
WALL CONSTRUCTION HARDWARE REQUIRED
• Wood Stud Included
• Wood Beam Included
• Solid Concrete Contact Qualifi ed Professional
• Cinder Block Contact Qualifi ed Professional
• Brick Contact Qualifi ed Professional
• Other or unsure? Contact Qualifi ed Professional
Tools Needed for Assembly
• stud fi nder ("edge to edge" stud fi nder is
recommended)
• drill
Table of Contents
Parts List ............................................................................................................................................................................... 3
Removing bay door ............................................................................................................................................................... 5
Wall installation .......................................................................................................................................................................7
Wall plate installation ............................................................................................................................................................. 8
Reinstalling door ....................................................................................................................................................................9
Attaching vertical brackets to screen ............................................................................................................................. 10,11
Mounting and removing screen ...........................................................................................................................................12
Depth Adjustment .............................................................................................................. .................................................. 14
Setting Thermotstat ........................................................................................................... ..................................................15
Filter Replacement .............................................................................................................................................................. 17
• phillips screwdriver, 5 mm allen wrench,
fl athead screwdriver
• 5/32" (4 mm) bit for wood stud wall
• level
• hammer
2 of 18
ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11
Before you begin, make sure all parts shown are included with your product.
A
Parts may appear slightly different than illustrated.
Parts List
FPE42F-S FPE42FH-S FPE42F-B
Description Qty. Part # Part # Part #
enclosure assembly 1 061-7246 061-7304 061-T1246
adapter brackets 2 201-P1513 201-P1513 201-P1513
B
wood screws 6 5S1-015-C03 5S1-015-C03 5S1-015-C03
C
sealed washer 6 540-4067 540-4067 540-4067
E
ROXTEC cable seal 1 600-0107 600-0107 600-0107
F
key 1 600-0116 600-0116 600-0116
G
12 mm flat head screw 4 520-2325 520-2325 520-2325
H
serrated locknut 4 530-2021 530-2021 530-2021
I
wall plate 1 201-P1018 201-P1018 201-P1018
J
cord cover plate assembly (not shown) 2 061-7285 061-7285 061-T1285
K
4 mm allen wrench 1 560-1727 560-1727 560-1727
L
A
C
B
J
F
E
G
HI
L
3 of 18
ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11
Adapter Bracket Fasteners
M4 x 12 mm (4)
(504-9013)
M6 x 25 mm (4)
(520-1208)
M4 x 25 mm (4)
(504-1015)
.75" spacer (4)
(540-1059)
M5 x 12 mm (4)
(520-1027)
.5" spacer (4)
(540-1057)
M8 x 16 mm (6)
(520-9257)
M5 x 25 mm (4)
(520-9543)
M6 x 12 mm (4)
(520-1128)
M8 x 40 mm (4)
(520-1136)
M6 x 20 mm (4)
(520-9402)
multi-washer (4)
(580-1036)
M6 x 30 mm (4)
(510-9109)
M8 x 25 mm (4)
(520-1031)
4 of 18
ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11
Optional Removal of Bay Door
WARNING
• Grasp bay door fi rmly. Bay door will swing freely when gas springs are removed.
Bay door may be removed for ease of installation
1
to mounting surface. NOTE: Removal of bay door
is optional. Installation may be completed without
removing bay door.
Insert fl athead screwdriver under brass clip of gas
spring shown in detail 1 and pry up. Pull gas spring
away from bay door.
BRASS CLIP
BAY DOOR
MAIN ENCLOSURE
ASSEMBLY
1-1
Remove center set of 10-24 x .5" phillips screws
from inside of enclosure assembly (A) as shown in
fi gure 1.1. Slide bay door to the right to disengage
hinges and lift off of enclosure assembly.
A
10-24 x .5"
PHILLIPS SCREWS
fi g. 1.1
GAS SPRING
BRASS CLIP
DETAIL 1
5 of 18
ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11
Installing Cables
Removal of Rear Supports: Loosen 1/4-20 x
1-2
2.36" screws at top and bottom of rear supports as
shown in detail 2. Lift up rear supports, tilt to the
side, and pull out of carriage supports as shown in
detail 3.
1/4-20 SCREWS
REAR SUPPORTS
1/4-20 SCREWS
Cables may be routed through top, bottom, or rear
2
of main enclosure assembly. An additional available
option for cable entry while maintaining the waterproof
seal of the enclosure is the ROXTEC cable gland (F).
Install ROXTEC hardware to top, bottom, or rear of
enclosure assembly (A). NOTE: If cables are routed
through rear enclosure assembly hole, wall mount is
required for mounting to wall.
Follow the ROXTEC manufacturers' instructions for
installation included in ROXTEC cable gland (F) box.
Install cord cover plate assembly (K) to remaining
open holes of enclosure assembly (A) as shown in
detail 4.
DETAIL 2
REAR SUPPORTS
DETAIL 3
A
K
DETAIL 4
CARRIAGE
SUPPORTS
6 of 18
ISSUED: 07-16-10 SHEET #: 061-9050-4 03-04-11
Loading...