peerless-AV CL-42PLC68-OB, CL-47PLC68-OB, CL-55PLC68-OB, CLP-42PLC68-OB, CLP-47PLC68-OB User Manual
...
1
2014-06-13 #:220-9002-5 2015-02-24
OUTDOOR HD DISPLAY
MODEL:
CL-42PLC68-OB, CL-47PLC68-OB, CL-55PLC68-OB,
CLP-42PLC68-OB, CLP-47PLC68-OB, CLP-55PLC68-OB
User Manual
www.peerless-av.com
2
2014-06-13 #:220-9002-5 2015-02-24
General Safety Precautions ...................................................................................................................3
FCC Caution ...................................................................................................................................5
FCC Statement ...............................................................................................................................5
Notice .............................................................................................................................................5
Relevant Information .....................................................................................................................5
System Installation And Electrical Requirements ..................................................................................6
Electrical Code ...............................................................................................................................6
Power Source ................................................................................................................................6
Set Up Instructions .................................................................................................................................7
What's In The Box ..........................................................................................................................7
Ambient Light Sensor .....................................................................................................................7
Connecting Cables .........................................................................................................................8
Source Connection Guide ......................................................................................................8
Cable Seals ............................................................................................................................9
Installation Of The Rear Cover Plate ......................................................................................9
Connect To The Power Source .....................................................................................................10
Prepare Your Display For Mounting .............................................................................................10
Prepare The Screen For Viewing .................................................................................................11
Battery Installation And Replacement ..........................................................................................11
Power On/Off the Display .............................................................................................................11
Operating Instructions ..........................................................................................................................12
Using The Remote Control ...........................................................................................................12
Rear Keypad Controls ..................................................................................................................12
(RS-232C) Serial Control Of The Display ....................................................................................13
Communication Conditions .................................................................................................13
Communication Procedure ..................................................................................................13
Control Codes ......................................................................................................................13
Navigating The On-Screen Menu ................................................................................................14
Picture .................................................................................................................................14
Audio ...................................................................................................................................14
Time ....................................................................................................................................14
Setup ...................................................................................................................................14
Lock .....................................................................................................................................14
Channel ................................................................................................................................14
Tips .......................................................................................................................................................15
Troubleshooting ............................................................................................................................15
Care Of Screen ...........................................................................................................................15
Mobile Telephone Warning ..........................................................................................................15
End Of Life Directives ..................................................................................................................15
License Agreement & Trademark Notice .....................................................................................15
Product Specifi cations ..................................................................................................................... ....16
Warranty ..............................................................................................................................................19
CONTENTS
3
2014-06-13 #:220-9002-5 2015-02-24
Read before operating equipment
Thank you for purchasing our product. Before using it, please read this user manual carefully
and follow the instructions correctly for safe operation. Please keep this manual handy for future
reference. Also, please be sure to always include this user manual in the packaging when transferring
or transporting this product to a different location.
The lamps in this product contain mercury. Please dispose according to state, local or federal law.
Batteries Installed Warning
CAUTION - Danger of explosion if batteries are incorrectly re-placed. Replace only with the same or
equivalent type. The batteries shall not be exposed to excessive heat such as sunshine, fi re or the
like.
CAUTION:
These servicing instructions are for use by qualifi ed service personnel only. To reduce the risk of
electric shock, do not perform any servicing other than that contained in the operating instructions
unless you are qualifi ed to do so.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not defeat the safety purpose of the polarized or grounding- type plug A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fi t into your outlet, consult an electrician for replacement of the obsolete outlet.
6. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
7. Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, does not operate
normally, or has been dropped.
8. Only use attachments/accessories specifi ed by the manufacturer.
9. In case of emergency such as fi re or electric shock caused by the product, immediately contact
911 or proper emergency police / fi re service agencies in your country.
10. If monitor or glass is broken, do not come in contact with the liquid crystal and handle with care.
11. Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.
12. An outdoor antenna should not be located near overhead power lines or any electrical circuits.
13. If an outside antenna is connected to the receiver, confi rm that the antenna system is grounded
to protect against voltage surges and built up static charges Section 810 of the National Electric
Code, ANSI/NFPA No 70-1984, provides information with respect to proper grounding for the
mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of
grounding connectors, location of antenna discharge unit, connection to grounding electrodes and
requirements for the grounding electrode.
14. Use properly rated power voltage. Use of non-rated voltage may cause fi re, electric shock and
severe damages to the product.
15. Do not open the cabinet under any circumstances. High voltage inside of this product may cause
electric shock.
GENERAL SAFETY PRECAUTIONS
RISK OF ELECTRICAL SHOCK
To reduce the risk of electric shock, do not disassemble the unit under any circumstances. No
user serviceable parts inside. All product services should be done by the Peerless-AV certifi ed
service personnel.
WARNING
4
2014-06-13 #:220-9002-5 2015-02-24
16. Under any circumstances, do NOT modify or disassemble this product as it may cause fi re,
electric shock, or severe damages to the product. Also any unauthorized modifi cations made to
the product automatically void product warranty.
17. Never touch antenna lines or wires, if applicable or power cables or power plugs in such
circumstances as lightning and thunder as it may cause electric shock.
18. Any severe physical impact on the product may cause certain components to fall out of place
within or to break, which may cause fi re or electric shock. In such event, do not operate the
product. Contact the manufacturer for support.
19. Clean dust off the power plug, periodically, to keep it clean and dry, ensuring proper and safe
operation of the product.
20. Do NOT destroy, process, or place the product close to any heating device; do NOT bend or twist
power cords, power plugs, cables, or wires with excessive force; do NOT place any heavy object
on the product as all of the above may cause damages to the product and result in fi re or electric
shock.
21. Do NOT touch power plugs with wet hands.
22. Always make sure to plug in the power plug fi rmly and completely. Incompletely placed power
plugs may cause fi re or electric shock due to built up heat emission.
23. Do NOT use any non-rated power sockets or power strips with many other devices jointly plugged
in. The wire of non-designated capacity may cause fi re due to built up heat emission. Try to use a
single, directly dedicated and rated GFI power socket for the product for safe operation.
24. In case of product malfunction or unusual events such as electrical burning smell, smoke, or loss
of content signals on TV/Display due to internal overheating, immediately turn off and unplug the
power and contact the manufacturer.
25. Do NOT install the product at such unstable locations as moving objects, constantly vibrating
props, or uneven surfaces. Improper installation may cause products to fall off. Follow mounting
instructions properly for safe operation of the product.
26. Do NOT install the product near any poisonous gas or chemically unstable atmosphere as it may
cause fi re.
27. Do NOT install the product near any strong magnetic or electrical current fi eld. It may cause
fi re, electric shock, or severe damages to the product. The product may be subject to any
electromagnetic radiation, causing deterioration of content picture quality.
28. Do NOT leave any fi re source such as candles close to or on the product as it may be a cause for
fi re or damages to the product.
29. Do NOT move or transport the product with any cables (power cables, content connectivity
cables) plugged in to the source devices. Damages may occur to the cables, plugs, or jointing
connectors of the cables due to forcible bending and stress, which may cause damages to the
waterproof seal of the product, making it subject to fi re, electric shock, or shorted circuit.
30. When unplugging, always grab the plugs of power cords or cables. Improper pulling of the cords
or cables may cause damages to the waterproof seal of the product, making it subject to fi re,
electric shock, or shorted circuit.
31. Do NOT climb on the product.
32. Two persons or more shall transport the product.
33. Do NOT use any other power cords or connection cables than what is provided with the product
or from the manufacturer directly. Use of untested, unauthorized, or substituted power cords or
connection cables may be a cause for malfunction, fi re, electric shock, or severe damages to the
product. Also such use of improper or undesignated power cords or connection cables will void
product warranty.
34. Always leave the Power Off when plugging or unplugging the power cords or connection cables to
avoid electric shock or damages to the product.
35. Do NOT use any chemical such as paint thinner or benzene to clean the product’s exterior. It may
cause scratches on the surface, erasing proper indications, identifi cation labels, or instructions on
the exterior, which may be a cause for misuse and improper operation of the product.
5
2014-06-13 #:220-9002-5 2015-02-24
FCC CAUTION
To assure continued compliance and possible undesirable interference, ferrite cores may be used
when connecting this display to video equipment; and maintain at least 400mm spacing to other
peripheral device.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with these instructions,
may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encourage to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio/display technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
Notice
CAUTION: Please use the power cord provided
with this display in accordance with the table below
If a power cord is not supplied with this equipment,
please contact your supplier. Only plug equipment
into receptacles with GFI.
IMPORTANT: Peerless-AV is not responsible for
any issues created by water present at the plug/
receptacle insertion point.
Relevant Information
Be sure to keep record of your displays model number for future reference
Plug Type: North America
Plug Shape:
Region: USA/Canada
Voltage: AC 120V
6
2014-06-13 #:220-9002-5 2015-02-24
SYSTEM INSTALLATION AND ELECTRICAL REQUIREMENTS
Electrical Code
Note: To the display system installer: This reminder is provided to call attention to Article 820-44 of
the National Electric Code that provides guidelines for proper grounding and, in particular, specifi es
that the cable ground shall be connected to the grounding system of the facility. Outlet shall be
installed near the equipment and shall be easily accessible.
Note: Installation shall incorporate UL Listed external surge protection rated 2500 Vpk or less, for 150
to 300 Vac mains, installed in accordance with Article 285 of ANSI/NFPA 70 or applicable local codes.
Power Source
The display must be connected to a mains socket outlet with a protective earthing connection.
The main plug is used as the disconnect device and shall remain readily accessible.
This display operates on 100-240 volts 60 Hz, AC current. Insert the power cord into a 120 volts 60
Hz outlet. Never connect the display to direct current or anything other than the specifi ed voltage.
To prevent electric shock from the display, do not use with an extension cord, receptacle, or other
outlet unless the blades and ground terminal can be fully inserted to prevent blade exposure.
CAUTION: Never remove the back cover of the display as this can expose you to very high
voltages and other hazards If the display does not operate properly, unplug the display and call your
authorized dealer or service center.
CAUTION: Double pole/neutral fusing (ISO 3869. No 5036)
Antenna discharge unit
(NEC Section 810-20)
NEC National Electric Code
Ground clamp
Electric service
equipment
Ground clamps
Power service grounding
electrode system
(NEC Art 250 Part H)
Grounding conductors
(NEC Section 810-21)
Antenna lead-in wire
7
2014-06-13 #:220-9002-5 2015-02-24
Important:
1. The display is equipped with protective glass; however, it is best practice to never apply pressure
to the screen display area which may compromise the integrity of the display. The manufacturer’s
warranty does not cover user abuse or improper installations.
2. All cables and cable covers MUST be connected and attached prior to installation on mount.
3. When routing cables through the cable entry make sure that the cables are formed in such a way
as to remove any stress on the connectors.
4. Installation shall be in accordance with the applicable parts of Chapter 8 of ANSI/NFPA70.
What's In The Box
Display
Remote (REM-0005)
Cord Cover
14 Screws (SCR-0043)
User Manual
SET UP INSTRUCTIONS
Ambient Light Sensor (May not be available on all models)
This display is equipped with an ambient light sensor which allows the display to intelligently adjust
the display's brightness based on the ambient lighting of the room or environment the display is
located in. A switch to turn the sensor on or off is located on the back of the display.
1. Ambient light sensor on: Your display's brightness will automatically dim as ambient lighting
decreases.
2. Ambient light sensor off: Your display settings will remain at full brightness even if the ambient
lighting of the room or environment changes.
Hint: Set the ambient light sensor switch to your desired setting before installing the display's rear
cover plate to avoid having to remove the display's rear cover plate to access the switch.
Power Cord
8mm Socket Bit
5.5mm Socket Bit
Fuse Lock Down Plate
8
2014-06-13 #:220-9002-5 2015-02-24
Connecting Cables
Source Connection Guide
Connect cables from the source devices to their appropriate connector on the display.
Note: Your display's serial number can be found on the box and underneath the rear cover plate.
2 1
Antenna or Cable
HDMI 2
Coaxial SPDIF
S-Video
AV / Video
AV / Audio L
AV / Audio R
Component 1 / PR
Component 1 / PB
Component 1 / Y
HDMI 1
VGA
PC Audio
USB
Audio Out
3
Antenna or Cable
HDMI 2
Coaxial SPDIF
AV / Video
AV / Audio L
AV / Audio R
Component 1 / PR
Component 1 / PB
Component 1 / Y
HDMI 1
VGA
PC Audio
USB
Audio Out
HDMI 3
For display with serial
number that starts with 12 or 14
For display with serial
number that starts with 15
9
2014-06-13 #:220-9002-5 2015-02-24
Cable Seals
1. Plug cables into proper input connection.
2. Run cable across foam gasket block.
Notes: a. If running one cable per block,
run cable over middle of cable
block.
b. If running more than one cable
on a block, ensure that cables
are at least ¼” apart to allow for
proper sealing.
3. Cables will be sealed when rear cover plate
is attached and screwed into place.
Installation Of The Rear Cover Plate
1. Place cover plate directly over cables aligning
holes with screw inserts.
2. Apply pressure to center of cover plate.
Note: Foam gasket block should
compress when pressure is applied.
3. Screw in screws until they will no longer
tighten.
Note: Do not over torque screws as
they may strip and damage the cable
seal.
4. When all screws are installed properly, the
cables should appear to be completely
encapsulated between the cable gland and
the back cover plate.
10
2014-06-13 #:220-9002-5 2015-02-24
Prepare Your Display For Mounting
Note: Install cables prior to mounting your display. Cable entry cover may be obstructed once the
display is mounted.
IMPORTANT:
1. Do not apply pressure to the screen display area which may compromise the integrity of the
display. The manufacturer’s warranty does not cover user abuse or improper installations.
2. For portrait mounting rotate the display so that the rear cover plate and cord connections will be
on the right when viewing the display from the front.
Wall mounting solution is not included with the unit and is sold separately. Peerless-AV provides a
variety of all-weather mounting solutions. Contact your Peerless-AV representative for
all-environment mounting solutions.
For your safety, only mount with an UL listed wall mount bracket that supports the weight of the
display. When mounting the display outdoors or in harsh environments, only use wall mounts that are
designed to resist water, rust and wind.
Examine the chart below to determine the mounting specifi cations for your display:
Connect To The Power Source
Connect the supplied power cord to the display.
The display should be installed close to an easily accessible power outlet. Fully insert the prongs into
the power outlet socket. A loose connection may cause image degradation.
Only plug TV into an electrical outlet that has a GFI receptacle. If you run an extension cord, make
sure it is an outdoor rated cord and plug. Insure that is placed safely and out of the way of people and
animals.
600mm
400mm
600mm
400mm
CL-42PLC68-OB
CL-47PLC68-OB
CL-55PLC68-OB
CLP-42PLC68-OB
CLP-47PLC68-OB
CLP-55PLC68-OB
Model
Mounting Hole
Pattern
Required Mounting
Screws
CL-42PLC68-OB
CL-47PLC68-OB
CL-55PLC68-OB
600mm x 400mm Four M8 screws
CLP-42PLC68-OB
CLP-47PLC68-OB
CLP-55PLC68-OB
400mm x 600mm Four M8 screws
11
2014-06-13 #:220-9002-5 2015-02-24
Battery Installation And Replacement
The remote control is powered by two 15V AAA
batteries currently installed.
To install or replace batteries:
1. Remove the battery module of the remote
control by removing the two screws on the
end of the battery module. Slide the battery
module out of the remote control.
2. Insert two new “AAA” size batteries into the
battery module.
Important: Match the batteries to the (+)
and (-) marks on the battery module and
remote control.
3. Slide the battery module back into the remote
control and reinserting the two screws in the
end of the battery module.
Incorrect usage of batteries can result in leaks
or bursting. Peerless-AV recommends the
following battery use:
1. Do not mix battery brands.
2. Do not combine new and old batteries. This
can shorten the battery life or cause liquid
leakage of the batteries.
3. Remove dead batteries immediately to
prevent battery acid from leaking into the
battery compartment.
4. Do not touch exposed battery acid as it
may injure skin.
5. Remove the batteries if you do not intend
to use the remote control for a long period
of time.
CAUTION
Power On/Off Your New Display
Power on your display by using the remote control or the rear power key as shown below. The display
will power on but image may not appear for a few seconds as it completes it's power up sequence.
Remote control
Point the remote control at the IR sensor located
in the upper right corner of the display and press
the power key.
Power Key
Rear Power Key
To access the rear keypad follow the procedures
found in the "Rear Keypad Controls" section.
Press the blue power key.
Prepare The Screen For Viewing
1. Remove protective fi lm from the screen.
2. Clean the screen with an approved screen cleaner or Isopropyl alcohol designated in the "Care of
Screen" section. Do not use any window cleaners or anything containing ammonia.
12
2014-06-13 #:220-9002-5 2015-02-24
OPERATING INSTRUCTIONS
Using The Remote Control
Power On/Off
Source Select
Quick Source
Selection Buttons
Channel Up/Down
Volume Up/Down
Menu Controls
(Up/Down/Left/Right)
Select
Number Pad
Select Picture
Mode
Select Sound Mode
Enable/Disable
Sleep Timer
& Set Sleep
Interval
Favorite Channel
Up/Down
Select Zoom Mode:
(Normal, Wide,
Zoom, Cinema)
Closed Captioning
On/Off
Multichannel TV Sound;
Select Alternate Program
Language (If available)
Select On
Screen Menu
(Press menu
button to go
back while in
the menu)
Terminate Menu Mode
Display
Electronic
Program Guide
(If available)
Mute SoundDisplay Favorite Channel List
Display Channel,
Audio, Video and
Signal Information
Rear Keypad Controls
To access the keypad, the cover plate located on the back of the display must be removed. Remove
the fasteners using the supplied 5.5 mm socket bit. Reinstall the keypad cover to prevent any water
from entering the unit.
DIRECT MODE: Allows for quick access to source selection, volume settings and channel selection.
MENU MODE: Press the MENU button to access MENU MODE and activate the On Screen Display
(OSD). For a description of OSD operation refer to the next section.
The keypad buttons are assigned as indicated in the table below.
DIRECT
MODE
Channel Down
Channel Up
Menu
Volume Down
Volume Up
Input Select
On/Off
MENU
MODE
-
Select
Menu
Left
Right
Auto Confi g
On/Off
13
2014-06-13 #:220-9002-5 2015-02-24
(RS-232C) Serial Control Of The Display
Attach an RS-232C cable cross-type (commercially available) to the supplied Din/D-Sub RS-232C for
the connections.
Note: This operation system should be used by a person who is accustomed to using computers.
Function Code
Menu A0, F0, 55, FF, 4E, B1
Right A0, F0, 55, FF, 05, FA
OK A0, F0, 55, FF, 02, FD
Down A0, F0, 55, FF, 0D, F2
Up A0, F0, 55, FF, 17, E8
Left A0, F0, 55, FF, 0C, F3
Source A0, F0, 55, FF, 01, FE
(1) A0, F0, 55, FF, 42, BD
(2) A0, F0, 55, FF, 43, BC
(3) A0, F0, 55, FF, 0F, F0
(4) A0, F0, 55, FF, 1E, E1
(5) A0, F0, 55, FF, 1D, E2
(6) A0, F0, 55, FF, 1C, E3
(7) A0, F0, 55, FF, 18, E7
(8) A0, F0, 55, FF, 45, BA
(9) A0, F0, 55, FF, 4C, B3
(0) A0, F0, 55, FF, 56, A9
Exit A0, F0, 55, FF, 1B, e4
Power On A0, F0, 55, FF, AE, 51
Power Off A0, F0, 55, FF,AF, 50
Power On/Off A0, F0, 55, FF, 0B, F4
Volume + A0, F0, 55, FF, 0A, F5
Volume - A0, F0, 55, FF, 40, BF
Channel + A0, F0, 55, FF, 55, AA
Channel - A0, F0, 55, FF, 5A, A5
Function Code
Mute A0, F0, 55, FF, 14, EB
Sleep A0, F0, 55, FF, 53, AC
AV A0, F0, 55, FF, ED, 12
VGA A0, F0, 55, FF, EA, 15
HDMI A0, F0, 55, FF, EC, 13
HDMI1 A0, F0, 55, FF, E1, 1E
HDMI2 A0, F0, 55, FF, E2, 1D
S-VIDEO A0, F0, 55, FF, E4, 1B
TV A0, F0, 55, FF, E8, 17
DTV A0, F0, 55, FF, E9, 16
Component A0, F0, 55, FF, E7, 18
USB A0, F0, 55, FF, 57, a8
PMODE A0, F0, 55, FF, 4B, B4
Zoom A0, F0, 55, FF, 51, AE
Surround A0, F0, 55, FF, C7, 38
SMODE A0, F0, 55, FF, 5B, A4
Text A0, F0, 55, FF, 59, A6
VOL 25% A0, F0, 55, FF, 21, dE
VOL 50% A0, F0, 55, FF, 22, dD
VOL 75% A0, F0, 55, FF, 23, dC
VOL 100% A0, F0, 55, FF, 24, dB
Brightness 25% A0, F0, 55, FF, 26, d9
Brightness 50% A0, F0, 55, FF, 27, d8
Brightness 75% A0, F0, 55, FF, 28, d7
Brightness 100% A0, F0, 55, FF, 29, d6
Communication Conditions
Set the RS-232C communication settings on the
PC to match the TV’s communication conditions.
The TV’s communication settings are as follows:
Baud Rate .........................38,400 bps
Data Bits .....................................8 bits
Parity ..........................................None
Stop Bit .........................................1 bit
Communication Procedure
Send the control commands from the PC via the
RS-232C connector.
The TV operates according to the received
command and sends a response message to the
PC.
Do not send multiple commands at the same time
- wait until the PC receives the response before
sending the next command.
Control Codes
14
2014-06-13 #:220-9002-5 2015-02-24
Picture
Picture Mode Standard
Dynamic
Soft
Personal
Contrast Adjust contrast level
Brightness Adjust brightness level
Color Adjust color level
Tint Adjust tint level
Sharpness Adjust sharpness level
Color Mode Normal
Cool
Warm
Audio
Sound Mode Standard
Music
Movie
Personal
Bass Adjust bass level
Treble Adjust treble level
Balance Adjust balance level
Surround On/Off
AVC
(Automatic
Volume Control)
On/Off
SPDIF Type
(Digital Audio
Output Format)
PCM
Raw
Audio Language English
Spanish
French
Navigating The On Screen Menu
Pressing the menu key on the remote or rear keypad will cause the On Screen Display (OSD) main
page to be displayed with fi ve menu tabs: Picture, Audio, Time, Setup, Lock and Channel. Use the
cursor keys to move through the various sub menus. Pressing the menu key again will move the
selection back one level. Press exit to quit.
Time
Sleep Timer Set time interval to turn off
inactive display
Time Zone Select time zone
Daylight
Savings Time
On/Off
Clock No options
Lock
Password Set user password to
prevent unauthorized
access to OSD
Channel
Air/Cable Choose between Antenna
and Cable
Auto Scan Searches for available
channels
Favorite Shows favorite channels
Show/Hide Enable/Disable unwanted
channels
Channel No. No options: Displays list of
channels
Channel Label Change channel names
DTV Signal Displays channel info and
signal strength
Setup
Menu
Languages
English
Spanish
French
Transparency On/Off
Zoom Mode Normal
Wide
Zoom
Cinema
Noise Reduction Off
Weak
Middle
Strong
Advanced No Option
Closed Caption
Basic Selection:
Advanced
Selection:
Option:
On/Off
CC 1-4
Text 1-4
Service 1-6
Select Font Size, Color
and Opacity
XVS On/Off
Restore Defaults Restore all options to their
original settings
15
2014-06-13 #:220-9002-5 2015-02-24
Care Of The Screen
Do not rub or strike the screen with anything hard as this may scratch, mar, or even damage the
screen permanently .
Never use ammonia or any cleaner containing ammonia, as it will damage the anti-glare coating on
the screen. Only use Isopropyl alcohol or an approved screen cleaner to clean the screen.
Protective covers are available for Peerless-AV all-weather TVs. Contact your Peerless-AV
representative to get the right cover for your screen.
Unplug the power cord before cleaning the screen Dust the display by wiping the screen and the
cabinet with a soft, clean cloth If the screen requires additional cleaning, use a clean, damp cloth Do
not use liquid cleaners, aerosol cleaners, or solvents of any kind.
Mobile Telephone Warning
Keep your mobile telephone away from your display to avoid disturbances in the picture or sound,
possibly causing permanent damage to your display.
End Of Life Directives
In an effort to produce environmentally friendly products. your new display contains materials that can
be recycled and reused. At the end of your display life, specialized companies can minimize display
waste by separating reusable materials from non-reusable materials. Please ensure you dispose of
your display according to local regulations.
License Agreement And Trademark Notice
HDMI, the HDMI logo and High-Defi nition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
Manufactured under license from Dolby Laboratories Dolby and the
double-D symbol are trademarks of Dolby Laboratories
Troubleshooting
TIPS
No Picture • Check that the display is turned on.
• Is the power cord inserted into a power outlet?
• Test the power outlet by plugging in another device into the outlet.
Remote Control
Doesn’t Work
• Make sure there is a direct path between the remote control and the IR
receiver located at the top right of the display.
• Was the shipping tab removed and the battery re-installed correctly?
• Install new battery.
Picture Appears
Slowly After
Switching On
• This is normal; the display image is disabled during the start up process.
• After an image appears it can take several minutes for the LCD display to
reach it’s normal operating brightness.
• On fi rst use activate power control by pressing power button on remote.
®
16
2014-06-13 #:220-9002-5 2015-02-24
Specifi cations subject to change without notice
PRODUCT SPECIFICATIONS
Display
Screen Size
CL-42PLC68-OB
CL-47PLC68-OB
CL-55PLC68-OB
CLP-42PLC68-OB
CLP-47PLC68-OB
CLP-55PLC68-OB
42" diagonal
47" diagonal
55" diagonal
42" diagonal
47" diagonal
55" diagonal
Aspect Ratio 16:9
Resolution 1920 x 1080
Brightness 700 cd/m
2
Backlight
Adjustment
Automatic (ambient light
sensor)
Contrast Ratio* 1000:1
Viewing Angle 178° vertical/horizontal
Response Time 9ms (gray to gray)
Refresh Rate
CL-42PLC68-OB
CL-47PLC68-OB
CL-55PLC68-OB
CLP-42PLC68-OB
CLP-47PLC68-OB
CLP-55PLC68-OB
60 Hz
60 Hz
120 Hz
60 Hz
60 Hz
120 Hz
TV Controller Features
Analog TV NTSC
Digital TV ATSC
Picture
Adjustment
Brightness/Contrast/
Saturation/Tint/Sharpness/
Noise reduction
Picture Mode Standard, Dynamic,
Personal, Soft
Color
Temperature
Adjustment
Cool, Normal, Warm
Screen
Adjustment
Normal/Wide/Zoom
Clock, Sleep
Timer
Yes
MTS Yes
V-chip Yes
Closed Caption Yes
Electronic
Program Guide
Yes
Noise Reduction Yes
3-D Comb Filter
and De-interlace
Yes
Mute Yes
OSD Language English, French, Spanish
* Enhanced for direct sunlight usage.
Power
AC Input 90 VAC to 240 VAC,
50 to 60 Hz
Power
Consumption
CL-42PLC68-OB
CL-47PLC68-OB
CL-55PLC68-OB
CLP-42PLC68-OB
CLP-47PLC68-OB
CLP-55PLC68-OB
Display: 101 W
Heater: 700 W
Display: 135 W
Heater: 700 W
Display: 145 W
Heater: 700 W
Display: 101 W
Heater: 700 W
Display: 135 W
Heater: 700 W
Display: 145 W
Heater: 700 W
Environmental
Operating
Temperature
-40° F to 140 F
Storage
Temperature
0° F to 124° F
(unit left plugged in)
IP Rating IP68
Nema Rating 6
Safety/EMC UL, FCC Class B
17
2014-06-13 #:220-9002-5 2015-02-24
Input/Output Connections
TV Input Coax, 75 ohm (x1)
VGA Input 15 pin D-SUB (x1)
HDMI Input HDMI (x2), 480i, 480p,
720p, 1080i, 1080p
S-Video Input Mini DIN (x1)
CVBS Input RCA (x1)
YPbPr Input RCA (x2), 480i, 480p,
720p, 1080i, 1080p
VGA Stereo
Audio Input
3mm Accessory Jack (x1)
CVBS Stereo
Audio Input
RCA (x1)
YPbPr Stereo
Audio Input
RCA (x2)
Audio Stereo
Output
3mm Jack (10W + 10W)
Mechanical
Display Size:
CL-42PLC68-OB
CL-47PLC68-OB
CL-55PLC68-OB
CLP-42PLC68-OB
CLP-47PLC68-OB
CLP-55PLC68-OB
(W x H xD)
38.2" x 22.2" x 6.0"
42.6" x 24.7" x 6.0"
47.3" x 27.4" x 6.0"
22.2" x 38.2" x 6.0"
24.7" x 42.6" x 6.0"
27.4" x 47.3" x 6.0"
Enclosure Color Black
Enclosure Glass Anti-refl ective and
UV protection
VESA Mount
CL-42PLC68-OB
CL-47PLC68-OB
CL-55PLC68-OB
CLP-42PLC68-OB
CLP-47PLC68-OB
CLP-55PLC68-OB
600 mm x 400 mm
600 mm x 400 mm
600 mm x 400 mm
400 mm x 600 mm
400 mm x 600 mm
400 mm x 600 mm
Net Weight
CL-42PLC68-OB
CL-47PLC68-OB
CL-55PLC68-OB
CLP-42PLC68-OB
CLP-47PLC68-OB
CLP-55PLC68-OB
92 lbs
110 lbs
138 lbs
92 lbs
110 lbs
138 lbs
Shipping Size
CL-42PLC68-OB
CL-47PLC68-OB
CL-55PLC68-OB
CLP-42PLC68-OB
CLP-47PLC68-OB
CLP-55PLC68-OB
(W x H x D)
42" x 26" x 8.3"
47" x 29" x 8.3"
53" x 32" x 8.3"
42" x 26" x 8.3"
47" x 29" x 8.3"
53" x 32" x 8.3"
Shipping Weight
CL-42PLC68-OB
CL-47PLC68-OB
CL-55PLC68-OB
CLP-42PLC68-OB
CLP-47PLC68-OB
CLP-55PLC68-OB
110 lbs
128 lbs
156 lbs
100 lbs
128 lbs
156 lbs
18
2014-06-13 #:220-9002-5 2015-02-24
This page intentionally left blank.
ENG
19
2014-06-13 #:220-9002-5 2015-02-24
The Peerless-AV Outdoor TV/Display is warranted to be free of defects in material and workmanship from the time of purchase by
the original owner. If this product is found and proved to be defective under the terms and conditions of this warranty, Peerless-AV
will repair or replace defective parts with new and/or reconditioned parts at no charge for the parts and labor to the original owner,
subject to the terms and conditions of this Limited Warranty.
This Limited Warranty covers failures due to defects in material or workmanship that occur during normal residential or commercial
use as follows:
1. Parts – the warranty period for parts are: two (2) years from the date of original purchase. During the applicable Limited
Warranty period for parts, defective parts will be replaced at no charge. Parts used for the replacement will be warranted for the
remainder of the original warranty period for those parts.
2. Labor – the warranty period for labor is: two (2) years from the date of original purchase. During the applicable Limited Warranty
period for labor, Peerless-AV will provide the labor for warranty repair at no charge for a period of two (2) years from the date of
original purchase.
3. Original owner must provide verifi cation of the date of purchase when requesting Limited Warranty Services. A copy of the
original Dated Sales Receipt is required together with the product to obtain service under this Limited Warranty. Product
Registration at the time of purchase is required.
4. All repairs must be performed by a Peerless-AV Authorized Service Provider.
5. Customer is responsible for returning (including any freight and shipping costs) defective unit to a Peerless-AV Authorized
Service Provider. If the product is found to have no defects, the customer will be responsible for return shipping costs as well.
THIS LIMITED WARRANTY DOES NOT COVER:
• Shipping damage.
• Damage caused during customer unpacking, and/or removal of packing materials.
• Damage due to improper, incorrect or insuffi cient AC voltage.
• Damage due to power surges or lightning strikes.
• Damage which results from fi re, fl ood, lightning, tornado, hurricane, large hail, extremely gusty winds, sand storms, vandalism,
terrorism or other acts of nature.
• Any unit which has been modifi ed or damaged due to improper installation or failure to obey the operating instructions provided
in the User Manual.
• Any failure, loss, damage or personal injury due to accident, neglect, misuse, abuse, improper operation, improper maintenance,
improper storage, alteration to the unit, or failure by the consumer to follow operating instructions provided in the User Manual.
• Any owner other than the original owner.
• Any unit purchased from an unauthorized seller.
• If the original product serial number has been removed, defaces or tampered with in any way.
• Any transportation charges incurred in connection with warranty services.
• Indirect, consequential, or special damages, except as required by federal or state laws.
• Any unit tampered with, modifi ed, adjusted or repaired by any party other than the Peerless-AV Authorized Service Provider.
• Any cosmetic damages to the surface or exterior that has been deface or faded, or caused by normal wear and tear or exposure
to chemicals, acid rain, large hail or adverse weather conditions.
• Because the TV/display cabinet and components are hand-assembled and altered, we do not cover minor cabinet blemishes or
minor scratches to the exterior of the unit.
• Picture quality when installed in direct sunlight and uncovered where sun is shining directly on screen.
• Any damage, scratches or blemishes to the screen and/or exterior cabinet due to end-user cleaning.
• Dirty air waves, and/or unusual signal interference due to weak signal from multi-wire runs or weak signal from cable or satellite
service providers or unusual signal interference or lack of distance when using the Digital Wireless Video/Audio Package.
• Return shipping when no defect is found.
Peerless-AV and its representatives or agents shall in no event be liable for any general, indirect or consequential damages arising
out of/or caused by the use of/or the inability to use this product.
This warranty is made in lieu of all other warranties, expressed or implied, and all other liabilities on the part of Peerless-AV. Any
other warranties, including the warranties of merchantability and fi tness for a particular purpose are hereby disclaimed by Peerless-
AV and its representatives and/or agents.
The laws of some states do not allow exclusion of implied warranties; therefore, this warranty shall be deemed modifi ed to be
consistent with such laws. This Limited Warranty gives you specifi c legal rights. You may also have other rights that vary from state
to state.
All warranty inspections and repairs must be performed by Peerless-AV or its authorized service representations.
Customer Care: 800.865.2112 or 630.375.5100
TWO YEAR PARTS & LABOR LIMITED WARRANTY
Peerless-AV
2300 White Oak Circle
Aurora, IL 60502
Email: tech@peerlessmounts.com
Ph: (800) 865-2112
Fax: (800) 359-6500
www.peerless-av.com
© 2015, Peerless Industries, Inc.
Loading...