Peerless-AV ACCXT302 Installation [en, es, fr]
Installation and Assembly:
Video Conferencing Shelf Accessory Kit
for Flat and Tilt Mounts
Model: ACCXT302
Max Load Capacity: 5 lb (2.3 kg)
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.com
ISSUED: 07-28-11 SHEET #: 120-9122-3 03-02-12
NOTE: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum Load Capacity. See page one.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws fi rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
Tools Needed for Assembly
• phillips screwdriver
• level
Before you begin, make sure all parts shown are included with your product.
Parts List
Description Qty.
A shelf 1 125-1270
B mount bracket 1 125-1271
C shelf bracket 1 125-1273
D adjustment bracket 1 125-1272
E M5 x 16mm self tapping screw 3 520-9515
F washer 3 540-9400
Parts may appear slightly different than illustrated.
Part #
A
E F
B
C D
2 of 17
ISSUED: 07-28-11 SHEET #: 120-9122-3 03-02-12
Connect mount bracket (B), adjustment bracket (D) and shelf bracket (C) with two screws (E) and two washers (F)
as shown. NOTE: Do not fully tighten screws (E) until step 3.
1
F
E
F
E
Attach the assembled brackets to shelf (A) as shown.
2
A
C
D
B
3 of 17
ISSUED: 07-28-11 SHEET #: 120-9122-3 03-02-12
NOTE: Display must be removed from display mount prior to installing shelf. Adjust brackets (B, C, D) to desired
height and tighten two screws (E) on the brackets.
3
DISPLAY
A
C
X
D
X + 1"
E
B
E
DISPLAY
MOUNT
Slide the video conferance shelf into the slot located on the front of your display mount. NOTE: The video
conferance shelf can also be installed to the bottom of the display mount. Adjust the video conferance shelf to
4
center horizontal position.
4 of 17
ISSUED: 07-28-11 SHEET #: 120-9122-3 03-02-12
Secure the video conferance shelf to your display mount with one screw (E) and one washer (F).
5
F
E
DISPLAY MOUNT
5 of 17
All other brand and product names are trademarks or registered trademarks of their respective owners.
ISSUED: 07-28-11 SHEET #: 120-9122-3 03-02-12
© 2012, Peerless Industries, Inc. All rights reserved.
Instalación y montaje:
Videoconferencia Plataforma kit de accesorios
para soportes de planos y de inclinación
Modelos: ACCXT302
Capacidad Máxima de Soportar Carga: 5 lb (2.3 kg)
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.com
PUBLICADO: 07-28-11 HOJA #: 120-9122-3 03-02-12
Loading...