Peavey SSE 6 User Manual
Description
The new SSE enclosure series features high
power ratings with custom components, a
sleek look and a unique, snap-in metal
grille. The SSE 6 is a two-way system
featuring the highly acclaimed Peavey 14XT
titanium compression driver with a Sound
Guard IV tweeter protection network and a
maximum-performance 6.5" woofer. It is
rated at 150 Watts program and 300 Watts
peak. This lightweight speaker system is
ideal for smaller venues where space is at a
premium. Connections include a four-pin
Neutrik
®
Speakon®or a paralleled twoposition terminal block for additional
cabinets. The SSE Series is available in
black, white and natural finishes.
Features:
• Two-way sound reinforcement enclosure
• Designed for permanent installation
• Premium 6.5" woofer
• Peavey 14XT
™
titanium compression
driver
• Sound Guard
™
IV tweeter protection
network
• Available in three finishes: black,
white or natural
• Mounting point for VersaMount™35
bracket
• 150 Watts program/300 Watts peak
power handling
• 100 Hz to 17 kHz
• 90 dB at 1W/1m
• 8 Ohms
Frequency response, 1 meter on-axis,
swept-sine in anechoic environment:
100 Hz to 17 kHz (±3 dB)
Usable low frequency limit (-10 dB
point):
80 Hz to 21 kHz
Power handling:
Full Range:
150 W program
300 W peak
Sound pressure level, 1 Watt, 1 meter in
anechoic environment:
Full Range:
90.0 dB SPL (2.83 V input)
Maximum sound pressure level (1
meter):
Full Range:
108.8 dB SPL continuous
114.8 dB SPL peak
SPECIFICATIONS
SSE™6
2
Radiation angle measured at -6 dB
point of polar response:
500 Hz to 1.6 kHz:
Horiz. 145° +/- 55°
Vert. 165° +/- 100°
1.6 kHz to 5 kHz:
Horiz. 115° +/- 65°
Vert. 110° +/- 70°
5 kHz to 16 kHz:
Horiz. 95° +/- 15°
Vert. 95° +/- 15°
Directivity factor, Q (Mean):
5.93 +/- 3.06
Directivity index, Di (Mean):
7.03 dB +/- 2.65 dB
Transducer complement:
Low Frequency Section:
one 6.5" premium Peavey woofer
High Frequency Section:
Peavey 14XT
™
titanium diaphragm
compression driver on a 90° H x 90° V
conical horn
Box tuning frequency:
Low Frequency Section:
100 Hz
Harmonic distortion:
1% rated power
Second Harmonic:
100 Hz: 0.54%
1 kHz: 0.25%
Third Harmonic:
100 Hz: 1.97%
1 kHz: 0.46%
10% rated power
Second Harmonic:
100 Hz: 0.98%
1 kHz: 0.66%
Third Harmonic:
100 Hz: 2.45%
1 kHz: 0.66%
Crossover frequency (internal passive):
Low Frequency - High Frequency:
2.4 kHz
Impedance (Z):
Full Range:
Nominal: 8.0 Ω
Minimum: 8.5 Ω
Input connection:
One four-pin Neutrik®Speakon®in parallel
with one two-position terminal strip
Enclosure materials & finish:
Trapezoidal, dado-joined 13 mm birch
finished with a textured acrylic
polyurethane, with a full-length metal grille
covered with acoustical-grade grille cloth.
Available in black, white or natural finishes.
Mounting provisions:
(1) Mounting bracket and associated
hardware for attaching to SSE 6. This
bracket will allow for horizontal mounting to
walls and ceilings.
(4) 1/4"-20 threaded mounting points on
back to accommodate use of Versamount
™
35 adjustable mounting bracket.
Dimensions (H x W x D):
Front:
16.41" x 9.95" x 9.47"
417 mm x 253 mm x 240 mm
Rear:
16.41" x 5.23" x 9.47"
417 mm x 133 mm x 240 mm
Net weight:
21 lbs. (9.5 kg)
Frequency response
This measurement is useful in determining
how accurately a given unit reproduces an
input signal. The frequency response of the
SSE 6 is measured at a distance of 1-meter
using a 1 Watt (into the nominal impedance)
swept-sine input signal. As shown in figure
1, the selected drivers in the SSE 6 combine
to give a smooth frequency response from
100 Hz to 17 kHz.
Directivity
Beamwidth is derived from the -6 dB points
from the polar plots (see figure 3), which are
measured in a whole-space anechoic
environment. Q and Directivity Index are
plotted for the on-axis measurement
position. These specifications provide a
reference to the coverage characteristics of
the unit and provide insight into proper
placement and installation in the chosen
environment. The blending of the
components of the SSE 6 exhibit a desirable
beamwidth and directivity (figures 3 & 4)
suitable for sound reinforcement
applications.
Power handling
There are many different approaches to
power handling ratings. Peavey rates this
loudspeaker system's power handling using
a full-range form of the AES Standard 2-
1984. Using audio band 20 Hz to 20 kHz
pink noise with peaks of four times the RMS
level, this strenuous test signal assures the
user that every portion of this system can
withstand today's high technology music.
This rating is contingent upon having a
minimum of 3 dB available amplifier
headroom.
Harmonic distortion
Second and third harmonic distortions vs.
frequency are plotted in figures 5 & 6 for two
power levels. Ten percent (10%) of rated
input power and either one percent (1%) of
rated input power or 1 Watt, whichever is
greater. Distortion is read from the graph as
the difference between the fundamental
signal (frequency response) and the desired
harmonic. As an example, a distortion curve
that is down 40 dB from the fundamental is
equivalent to 1% distortion.
Mounting
Caution: Before attempting to mount this
speaker, consult a certified structural
engineer. The speaker may fall due to
improper installation, resulting in serious
injury and property damage. DO NOT
suspend or mount any other product or
device from this SSE 6 enclosure. The
maximum enclosure angle 45°. Use only
Grade 5 hardware or better. All associated
rigging is the responsibility of others.
Architectural & engineering
specifications
The loudspeaker system shall have an
operating bandwidth of 100 Hz to 17 kHz.
The nominal output level shall be 90.0 dB
when measured at a distance of 1 meter with
an input of 1 Watt. The nominal impedance
shall be 8.0 ohms. The maximum
continuous power handling shall be 75
Watts, with maximum program power of 150
Watts, a peak power input of at least 300
Watts and a minimum amplifier headroom of
3 dB. The nominal radiation geometry shall
be 120 degrees in the horizontal plane and
130 degrees in the vertical plane. The
outside dimensions shall be 16.41 inches
high by 9.95 inches wide by 9.47 inches
deep. The weight shall be 21 lbs. The
loudspeaker system shall be a model SSE 6.
3 + 2 YEAR LIMITED WARRANTY
NNOOTTEE::
For details, refer to the warranty
statement. Copies of this statement may
be obtained by contacting Peavey
Electronics Corporation, P.O. Box 2898,
Meridian, Mississippi 39301-2898.
SPECIFICATIONS
SSE™6
3
Amplitude Response (1W 1m On-Axis)
110
100
90
80
dB SPL (re 20 Pa)
70
60
20 50 100 200 500 1k 2k 5k 10k 20k
Figure 1
Frequency (Hz)
Impedance
100
50
30
20
Z
(
)
10
5
3
2
1
20 50 100 200 500 1k 2k 5k 10k 20k
Figure 2
Frequency (Hz)
360
300
180
140
100
80
60
40
Beamwidth (Degrees)
30
20 50 100 200 500 1k 2k 5k 10k 20k
Figure 3
Horizontal
Vertical
Frequency (Hz)
Q & Directivity Index
100
Q
10
1
Beamwidth
20 50 100 200 500 1k 2k 5k 10k 20k
Figure 4
Frequency (Hz)
20
Di
10
0
4
Harmonic Distortion : 10% Rated Power
120
110
100
90
80
70
dB SPL (re 20 Pa)
60
50
20 50 100 200 500 1k 2k 5k 10k 20k
Figure 5
Frequency (Hz)
2nd Harmonic
3rd Harmonic
Harmonic Distortion : 1% Rated Power
110
100
90
80
70
60
dB SPL (re 20 Pa)
50
40
20 50 100 200 500 1k 2k 5k 10k 20k
Figure 6
Frequency (Hz)
2nd Harmonic
3rd Harmonic
Loading...