Peavey PR 12 DATASHEET
FFrreeqquueennccyy rraannggee ((--1100 ddBB,, hhaallff
ssppaaccee))::
54 Hz to 21 kHz
SSeennssiittiivviittyy ((11 WWaatttt//11 mmeetteerr))::
97 dB
PPoowweerr rraattiinngg ((pprrooggrraamm))::
400 Watts
PPoowweerr ccaappaacciittyy ((ppeeaakk))::
800 Watts
TTrraannssdduucceerr ccoommpplleemmeenntt::
Heavy-duty 12" woofer with 2
3/8" voice coil and 50 oz.
magnet, RX14
™
1.4" titanium
diaphragm dynamic
compression driver
DDrriivveerr pprrootteeccttiioonn::
Positive temperature coefficient
resistor
NNoommiinnaall ccoovveerraaggee ppaatttteerrnn::
90˚ x 40˚
NNoommiinnaall iimmppeeddaannccee::
8 Ohms
IInnppuutt ccoonnnneeccttiioonnss::
Two 1/4" phone jacks in parallel
EEnncclloossuurree mmaatteerriiaallss aanndd ffiinniisshh::
Injection-molded, 1/4" thick
polypropylene with textured
finish; dark gray color
DDiimmeennssiioonnss ((HH xx WW xx DD))::
23.6875" x 17" x 13.75"
60.17 cm x 45.24 cm x 34.92 cm
Width in rear: 10" {24.5 cm}
WWeeiigghhtt::
33 lbs. (15 kg)
MMoouunnttiinngg oorr ssuussppeennssiioonn::
Molded-in stand-mounting cup,
top and bottom flying point
inserts
FFeeaattuurreess::
• Two-way sound reinforcement
enclosure
• 12" heavy duty woofer with 2
3/8" voice coil and 50 oz.
magnet
• RX14
™
1.4" titanium
diaphragm compression driver
• 400 Watts program/800 Watts
peak power handling
• Crossover network for driver
protection and EQ
• High frequency driver
protection
• 90˚ x 40˚ coverage constantdirectivity horn for better offaxis tonality
• Lightweight trapezoidal
enclosure
• Durable plastic injection-
SPECIFICATIONS PR™12
SPECIFICATIONS PR™12
molded
enclosure
• Heavy duty steel grille
• Molded-in pole mount
• Top and bottom flying point inserts
DDeessccrriippttiioonn
The PR 12 is a two-way sound
reinforcement system consisting of
a heavy duty 12" woofer and an
RX14
™
titanium diaphragm, dynamic
compression driver mounted on a
90˚ x 40˚ coverage constantdirectivity horn.
The lightweight-yet-rugged
injection-molded plastic enclosure
with molded-in stand-mount cup
facilitates portable use for live
music or speech sound. A black
powder-coated steel grille provides
driver protection and a professional
appearance.
The PR 112 speaker system is rated
at 400 Watts program power
handling, and the full crossover
network includes high voltage film
capacitors and high frequency driver
protection for clear, punchy sound
and excellent long-term reliability.
Two 1/4" phone jack input
connectors make daisy-chaining to
other speakers simple.
CCaauuttiioonn::
Before attempting to
suspend PR 12 consult a certified
structural engineer. The speaker
may fall due to improper
suspension, resulting in serious
injury and property damage.
Additional speaker enclosures
must not be suspended below a PR
12, nor should additional weight be
suspended from one of these units.
Use only the correct mating
hardware. All associated rigging is
the responsibility of others.
Always use all four inserts of a
given group as a set. NEVER use
just one insert to fly a cabinet! The
four insert groupings include a top
group and a bottom group, but
some models have an additional
group of four on the rear plane of
the cabinet. Maximum enclosure
angle from vertical hang: 30˚
When mounting or flying, you must
use a suitable safety chain or wire
rope to secure the speaker. Looped
through the top handle and firmly
attach to a suitable structural
member as indicated by a certified
structural engineer.
The recommended range of torque
for the mounting bolt is 3 to 3 1/2
lb./feet of torque. DO NOT
OVERTIGHTEN! If an insert spins, it
has been damaged and the cabinet
cannot be flown!
Never transport the cabinet while it
is mounted on an array bracket or
other mounting bracket, as this
may unduly stress the mounting
inserts.
WWAARRNNIINNGG!! ((nnoottee ttoo ssttrruuccttuurraall
eennggiinneeeerr))!!
The end of the mounting bolt
should not penetrate the cabinet
more than 5/16" beyond its
surface.
If this penetration depth is
exceeded, then the insert may be
damaged or unseated from the
cabinet, severely compromising its
mounting integrity!
The correct mounting bolt diameter
and threads per inch are: 1/4" x
20. We recommend the use of a
grade 5 bolt. For custom brackets,
we recommend a 5/16" hole for
the bolts to allow for tolerances
and adjustment.
33 ++ 22 YYEEAARR LLIIMMIITTEEDD WWAARRRRAANNTTYY
NNOOTTEE::
For details, refer to the
warranty statement. Copies of
this statement may be obtained
by contacting Peavey Electronics
Corporation, P.O. Box 2898,
Meridian, Mississippi 39301-2898.
Loading...