Peavey PR 10 DATASHEET

FFrreeqquueennccyy rraannggee ((--1100 ddBB,, hhaallff ssppaaccee))::

54 Hz to 21 kHz

SSeennssiittiivviittyy ((11 WWaatttt//11 mmeetteerr))::

95 dB

PPoowweerr rraattiinngg ((pprrooggrraamm))::

400 Watts

PPoowweerr ccaappaacciittyy ((ppeeaakk))::

800 Watts

TTrraannssdduucceerr ccoommpplleemmeenntt::

Heavy duty 10" woofer, RX14

™

1.4" titanium diaphragm dynamic compression driver

DDrriivveerr pprrootteeccttiioonn::

Positive temperature coefficient resistor

NNoommiinnaall ccoovveerraaggee ppaatttteerrnn::

90˚ x 40˚

NNoommiinnaall iimmppeeddaannccee::

8 Ohms

IInnppuutt ccoonnnneeccttiioonnss::

Two 1/4" phone jacks in parallel

EEnncclloossuurree mmaatteerriiaallss aanndd ffiinniisshh::

Injection-molded, 1/4" thick polypropylene with textured finish; dark gray color

DDiimmeennssiioonnss ((HH xx WW xx DD))::

19.5" x 14" x 13.125"

49.5 cm x 35.6 cm x 33.3 cm Width in rear: 8" {20.3 cm}

WWeeiigghhtt::

28 lbs. (12.7 kg)

MMoouunnttiinngg oorr ssuussppeennssiioonn::

Molded-in stand-mounting cup, top and bottom flying point inserts

BBuulllleettss::

• Two-way sound reinforcement enclosure

• 10" heavy duty woofer with 2" voice coil

• RX14

™

1.4" titanium diaphragm compression driver

• 400 Watts program/800 Watts peak power handling

• Crossover network for driver protection and EQ

• High frequency driver protection

• 90˚ x 40˚ coverage constantdirectivity horn for better offaxis tonality

• Lightweight trapezoidal enclosure

SPECIFICATIONS PR™10

• Durable plastic injection-molded enclosure

• Heavy duty steel grille

• Molded-in pole mount

• Top and bottom flying point inserts

DDeessccrriippttiioonn The PR 10 is a two-way sound reinforcement system consisting of a heavy duty 10" woofer and an RX14

™

titanium diaphragm, dynamic compression driver mounted on a 90˚ x 40˚ coverage constantdirectivity horn.

The lightweight-yet-rugged, injection-molded plastic enclosure with molded-in stand-mount cup facilitates portable use for live music or speech sound. A black powder-coated steel grille provides driver protection and a professional appearance.

The PR 10 speaker system is rated at 400 Watts program power handling, and the full crossover network includes high voltage film capacitors and high frequency driver protection for clear, punchy sound and excellent long-term reliability. Two 1/4" phone jack input connectors make daisy-chaining to other speakers simple.

CCaauuttiioonn::

Before attempting to suspend the PR 10, consult a certified structural engineer. The speaker may fall due to improper suspension, resulting in serious injury and property damage. Additional speaker enclosures must not be suspended below a PR 10, nor should additional weight be

suspended from one of these units. Use only the correct mating hardware. All associated rigging is the responsibility of others.

Always use all four inserts of a given group as a set. NEVER use just one insert to fly a cabinet! The four insert groupings include a top group and a bottom group, but some models have an additional group of four on the rear plane of the cabinet. Maximum enclosure angle from vertical hang: 30˚

When mounting or flying, you must use a suitable safety chain or wire rope to secure the speaker. Loop this through the top handle and firmly attach to a suitable structural member as indicated by a certified structural engineer.

The recommended range of torque for the mounting bolt is 3 to 3-1/2 lb./feet of torque. DO NOT OVERTIGHTEN! If an insert spins, it has been damaged and the cabinet cannot be flown!

Never transport the cabinet while it is mounted on an array bracket, or other mounting bracket, as this may unduly stress the mounting inserts.

WWAARRNNIINNGG!! ((nnoottee ttoo ssttrruuccttuurraall eennggiinneeeerr)) The end of the mounting bolt should not penetrate the cabinet more than 5/16" beyond its surface.

If this penetration depth is exceeded, then the insert may be damaged or unseated from the cabinet, severely compromising its mounting integrity!

The correct mounting bolt diameter and threads per inch are: 1/4" x

20. We recommend the use of a grade 5 bolt. For custom brackets, we recommend a 5/16" hole for the bolts to allow for tolerances and adjustment.

33 ++ 22 YYEEAARR LLIIMMIITTEEDD WWAARRRRAANNTTYY NNOOTTEE::

For details, refer to the warranty statement. Copies of this statement may be obtained by contacting Peavey Electronics Corporation, P.O. Box 2898, Meridian, Mississippi 39301-2898.

+ 2 hidden pages