Page 1
P1BT/P2BT
Column ARRAY
Specications
www.peavey.com
1
Page 2
FCC/ICES Compliancy Statement
This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS Standard(s). Operation
is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, that may cause undesired operation.
Le présent appareil est conforme aux CNR d’lndustrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes: (1) I’appareil ne doit pas produire de brouillage, et (2)
I’utilisateur de I’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
Warning: Changes or modifications to the equipment not approved by Peavey Electronics Corp. can void the user’s
authority to use the equipment.
Note – This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try and correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is con
nected.
• Consult the dealer or an experienced radio/TV technician for help.
-
Caution
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
Features and specifications are subject to change without notice.
Peavey Electronics Corporation • 711 A Street • Meridian, MS 39301
(601) 483-5365 • FAX (601) 486-1278 • www.peavey.com
© 2015
EX000030
2
Page 3
FCC Radiation Exposure Statement
is equipment complied with FCC radiation exposure limits set forth for an uncontrolled environment. is
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
IC Radiation Exposure Statement
is equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. e antenna should be installed and operated with minimum distance of 20 cm between the radiator and your body.
is transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Cet appareil est conforme aux limites d'exposition aux rayonnements de la IC pour un environnement non
contrôlé. L'antenne doit être installé de façon à garder une distance minimale de 20 centimètres entre la source
de rayonnements et votre corps. L'émetteur ne doit pas être colocalisé ni fonctionner conjointement avec à autre
antenne ou autre émetteur.
3
Page 4
P1BT/P2BT
Column Powered Speaker Systems
Congratulations on purchasing the Peavey P1BT/P2BT Powered Speaker System. ese compact, portable and powerful
stems are a perfect solution for the weekend warrior, singer songwriter or DJ. With a simple and intuitive layout, the P
sy
Series BT is a great plug and play option.
• Bluetooth stereo linking
• Bluetooth audio input for streaming music from any Bluetooth device
• 3 Channel mixer
• 2 XLR mic inputs and 1/4" Line Inputs
• RCA/3.5 mm Stereo input channel
• P1BT and P2BT have 180 Watts and 200 Watts
maximum power respectively.
• P1BT 2x6.5" Woofers with 1" (25mm) high-fre-
quency compression driver
•P2BT 3x6.5" Woofers with 1" (25mm) high-fre-
quency compression driver
Description:
e P Series BT is a compact, powerful, lightweight and low prole portable speaker system. Utilizing 180/200/260 watts
of potential maximum power, the units contain custom designed high frequency and woofer drivers. e P Series is
extremely easy to carry: an entire PA system that can be moved by one person in one trip.
e onboard mixer features 2 XLR and 1/4" inputs, two additional media channels feature stereo RCA/3.5mm inputs
and streaming audio Bluetooth in. Units also have ability to link with other P Series units for stereo operation. Perfect for
church, convention, DJ or club applications, the P Series oers the best-in-class feature-to-value and performance in the
indus t r y.
Installation Note:
is unit must have the following clearances from any combustible surface: top: 8", sides: 12", back: 12"
4
Page 5
P1 BT
Top Panel
12
13
PAIRING
STEREO LINK
7
6
5
4
2
3
1
5
8
Page 6
Input Panel
P1 BT
Subwoofer Out
PAIRING
STEREO LINK
(1) XLR Mic Input (Ch 1&2)
Use this XLR connector to connect a microphone to the P1/2BT speaker.
(2) Line Input (Ch 1&2)
Use this 1/4" (6.5mm) connector to connect a line-level source to the P1/2BT speaker. e line input is typically
used for sources like keyboards and CD players.
(3) RCA and 3.5mm Input (Ch 3)
ese inputs, RCA and 3.5mm (1/8") accept a stereo input from the output of an MP3 player, CD player, phone
or similar device.
(4) 3.5mm/RCA Input Selector (Ch 3)
is switch selects the source being sent to channel 3. In the upper position, the RCA inputs are sent to channel
3. In the lower position, the 3.5mm (1/8") connector is sent to channel 3.
(5) Level Control
Use this to adjust the source level in the corresponding channel.
(6) Low EQ (Bass)
is is an active tone control (shelving type: +/-15dB) that varies the level of the low frequency range.
Caution: Excessive low frequency boost causes greater power consumption and increases the possibility of
speaker damage.
(7) High EQ (Treble)
is is an active tone control (shelving type: +/-15dB) that varies the level of the high frequency range.
(8) Master Volume
e master volume control adjusts the overall level of the speaker.
(9)Power LED
LED illuminates when power has been applied to the speaker.
10
IN OUT
11
SYNC
POWER
9
(10) Sync XLR In/Out
e sync XLR In/Out connectors are used to daisy chain multiple speakers. Using these inputs, the signal source
can be fed to multiple speakers, while allowing the level of each speaker to be set by its own master volume control independent from the other speakers in the chain.
(11) Subwoofer Out
is 1/4" jack can be used to drive an external subwoofer amplier or a power sub. e signal level is pre-master
volume control. is allows the user to balance the signal between the speaker and the subwoofer.
6
Page 7
Bluetooth
(12) Bluetooth Pairing
Use this button to link your Bluetooth source (phone, tablet, etc...) to the speaker. See Bluetooth operation below.
(13) Bluetooth Stereo Link
Use this button to link your speaker to second P1/2BT speaker. See Bluetooth operation below.
Bluetooth Operation:
Pairing: To pair your bluetooth source to the speaker, use the following steps:
1. Press mode button on the back of the speaker to make the speaker discoverable. e pair
ing LED should start blinking.
2. Go to your devices bluetooth screen and select the available Peavey speaker. Once paired,
the pairing LED should light continuously.
Stereo Linking: To link two compatible P1/2BT speakers, use the following steps:
1. First, use the previous steps to pair your Bluetooth device to the rst speaker.
2. Press Pairing on the second speaker to turn the Bluetooth on.
3. Press Stereo Link button on both speakers. Once the connection has been made, the Stereo
Link LED 's on both speakers should be on continuously.
4. To disconnect, press the Stereo Link button again on either speaker.
7
Page 8
Rear Panel
SYNC
IN OUT
Subwoofer Out
POWER
CAUTION
AVIS:
RISQUE DE CHOC
ELECTRIQUE-NE PAS OUVRIR
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
WARNING:
THIS APPARATUS SHOULD NOT BE EXPOSED TO RAIN OR MOISTURE
AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT
AVIS:
DECHARGE ELECTRIQUE, CET APPAREIL NE DOIT PAS ETRE EXPOSE
A LA PLUIE OU A L’HUMIDITE ET AUCUN OBJET REMPLI DE LIQUIDE,
DANS LE BUT DE REDUIRE LES RISQUES D’INCENDIE OU DE
BE PLACED ON THIS APPARATUS.
TEL QU’UN VASE, NE DOIT ETRE POSE SUR CELUI-CI.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
CAN-ICES-3(B)/NMB-3(B)
WARNING: This speaker system can permanently damage hearing!
Use extreme care setting maximum loudness!
Soyez extrêmement prudent en réglant le volume maximum!
P3 BT
Electronics Corp.
Peavey
FCC ID: I4S-P3BT
CE0681
IC: 3642A-P3BT
Bluetooth Pairing
1. Press mode button to enter the BT pairing mode.
2. Connect your Bluetooth device to P3 BT.
Stereo Linking Two Speakers
1. Pair your Bluetooth device to rst speaker.
2. Press Pairing on the second speaker to turn BT on.
3. Press Stereo Link on both speakers under BT Mode.
4. To disconnect ,press the Stereo Link button again
on either speaker.
While Pairing or Linking LEDs will ash.
When Paired or Linked LEDs will be solid.
AC 115/230V 50-60Hz
Consumo de energia 180Wh
POWER
14
15
16
USE ONLY WITH 250V FUSE
100-240V
F2.5AL/250V
(14) Power Switch
e power switch is used to turn the speaker on and o
(15) AC Power Inlet
Never break o the ground pin on any equipment. It is provided for your safety. If the outlet used does not have
is is the receptacle for an IEC line cord, which provides AC power to the unit. Connect the line cord to this
connector to provide power to the unit. Damage to the equipment may result if improper line voltage is used.
(See line voltage marking on unit).
a ground pin, a suitable grounding adapter should be used and the third wire should be grounded properly.
To prevent risk of shock or re hazard, always make sure that the amplier and all associated equipment is
properly grounded.
(16) FUSE
To replace the fuse, be sure to remove the IEC power cord from the IEC socket. e fuse holder tray is
located beneath the IEC socket cavity. Pry the fuse holder tray out with a small at blade screwdriver placed
under the center of the top edge of the fuse tray, and gently lever the fuse tray out. e fuse is held in a clip in the
fuse tray, and should be removed and replaced with a fresh 5 X 20mm 250V type fuse of the appropriate current
would be the one that is NOT clipped into the fuse tray clips.
en, once the fresh fuse has been put in place, re-insert the fuse tray into the IEC connector assembly, and
rating. A spare fuse should be located in a hollow compartment in the fuse tray, below and behind the clip, this
make sure it is fully seated and ush with the outside of the IEC connector assembly.
It is recommended that to assure future convenience of having a spare, that a spare fuse be obtained and placed
in the hollow compartment at the earliest convenient time.
8
Page 9
Specifications
Connections 2 - XLR input jacks (Ch 1&2)
2 - 1/4" (6.35mm) TRS input jacks (Ch 1&2)
1 - 1/8" (3.5mm) TRS/stereo input (Ch 3)
1 - RCA input (Ch 3)
2 - XLR SYNC (In/Out)
1 - 1/4" (6.35mm) TRS (Subwoofer Output)
Frequency Response P1BT 60 - 19kHz
P2BT 50 - 19kHz
Peak Power P1BT 180 Watts (150W LF/30W HF)
P2BT 200 Watts (130W LF/70W HF)
Max Output SPL P1BT 98dB SPL (1W/1M)
P2BT 102dB SPL (1W/1M)
Bluetooth v5 A2DP streaming, stereo linking with a second P1/2BT speaker
Woof e r P1BT 2 x 6.5" (165mm) Woofer
P2BT 3 x 6.5" (165mm) Woofer
Tweeter P1BT 1" (25mm) high-frequency compression driver
P2BT 1" (25mm) high-frequency compression driver
Weight P1BT 15.4lbs (7kgs)
P2BT 33lbs (15kgs)
Dimensions (length x width x height) P1BT 23" x 9.25" x 10.5" (584mm x 235mm x 267mm)
P2BT 30" x 9.25" x 10.5" (762mm x 235mm x 267mm)
Power Supply 120VAC/60Hz or 230VAC/50Hz
9
Page 10
Logo referenced in Directive 2002/96/EC Annex IV
The bar is the symbol for marking of new waste and
13 August 2005
Peavey Electronics Corporation 5022 Hartley Peavey Drive Meridian, MS 39305 (601) 483-5365 FAX (601) 486-1278
10
www.peavey.com
Warranty registration and information for U.S. customers available online at
www.peavey.com/warranty
or use the QR tag below
Features and specications subject to change without notice.
(OJ(L)37/38,13.02.03 and defined in EN 50419: 2005
is applied only to equipment manufactured after
Loading...