Paxton TOUCHLOCK K series stainless steel keypad User Manual

30/11/2011

Ins-30006 TOUCHLOCK K series stainless steel keypad

Technical Support

01273 811011 [e-mail]

Technical help is available: Monday - Friday from 07:00 - 19:00 (GMT)

Saturday from 09:00 - 13:00 (GMT)

Documentation on all Paxton products can be found on our website - http://www.paxton.co.uk/

Fitting

Paxton

K75 Screw connector option

The unit should be mounted in conjunction with
an electrical backbox to achieve the required
clearance for the connector.

If an adaptor plate (310-750) is tted, the

mountings on the backbox can also be used.

Indoor use only

Cable extensions

Readers can be extended using Belden CR9540 10-core overall screened cable to a maximum of 100 metres.

Wiring

Connection to a control unit

When using this keypad style with Net2, the software version used must be v3.21 or later.

WHITE labelled Net2 control units provide 5V at the Red terminal. The Red power wire for

the reader should therefore be directly connected to the 12V ACU terminal.

Switch2 controllers with WHITE labels are incompatible with these products. The keypads in the K and KP series,

can only be used with Switch2 controllers tted with YELLOW wiring labels.

reader port

Connection modules

Reader junction box (325-020)

This module can be used to provide a
connection point for the reader RJ45 plug.
The terminals on the module are then wired
colour for colour to the controller.

Alternatively, the reader can be wired directly

into the screw terminals of the control unit by

rst cutting off the RJ45 plug and stripping

back the wires in the cable.

Further information on how to purchase Installer Tools is available at:

http://paxton.info/841

Reader port module (325-030)

This module may be purchased separately to speed up
the installation and replacement of readers.

The reader port module is designed to convert the
standard reader ports on Switch2 and Net2 controllers
to accept one or two RJ45 connections. Pull off the
screw terminal block from the reader port and simply
replace it with this module.

Suitability

Security-sensitive doors

Wet environments

Mounted on metal surface

Readers mounted together

Technical Help

Here is the list of topics about this product that receive the most technical support enquiries.

We list them here to help you speed up the installation and trouble shooting process.

1 - Net2 - Bell function.

QPressing the bell button on the keypad will result in Relay 2 being energised for 1 second. A bell sounder can be
Qcontrolled by wiring one of the bell feeds across COM / NO on the relay.

2 - Readers/keypads not working.

Q- Software settings - Conrm that the settings of the reader or keypad are correct.
Q- Connections - Check the wiring of the connectors. Where possible, test this reader on the other port.
Q- Extended Cable - Belden 9540 should be used. (100 m maximum) Twisted pair alarm cable should
Q not be used. To conrm that an extended cable is not at fault, wire the reader direct into the reader port.
Q- Supply voltage - Conrm that the voltage is within specication. (see table)
Q- User token - Conrm that the user token used for testing is OK by presenting it to a known working reader.
Q- Interference - Conrm whether the reader works when tested 'in hand' and not mounted on the wall. Ensure
Q that readers are not mounted back to back or there is no interference from other local RF devices.

3 - Readers/keypads - Extending cable.

QOnly Belden CR9538 / 9540 can be used for cable extensions. CR9538 8 core up to 25 m, CR9540 10 core for
Q25-100 m (maximum extension). With CR9540, the two additional cores should be used to double up for power.

4 - Switch2 - Initialising with 2 keypads.

QEither Keypad can be used to initialise the controller. Connect all wires in parallel, colour for colour.

5 - Switch2 (White label) & Touchlock Switch Control (922-177).

QThis keypad style does NOT work with these control units.

6 - Duress Codes.

QNet2 - Duress codes cannot be programmed into Net2.
QSwitch2 - These systems can accept Duress codes.

7 - Net2 - Replacing an old style keypad. (ACU Keypad port).

QWhen using this keypad with Net2, the software version used must be V3.21 or later and the keypad must be
Qwired into the reader port.

Specications

Electrical

Voltage

Current

Clock and data bit period

Vandal resistance

Environment

Operating temperatures - all items

Waterproof - Fixed cable

Waterproof - K75 - Screw connection

Cable length

Dimensions

K38 38 mm 78 mm

K50 50 mm 100 mm

K75 75 mm 143 mm

Min

8V DC 14V DC

Min

- 35 °C

IPX7

Width

Max

100 mA

Max

+ 66 °C

Height

600 µs

Medium

Outdoor use

Indoor use

5 metres

Depth

13 mm

15 mm

16 mm

This product is not suitable for retail sale. All warranties are invalid if this product is not installed by a competent person.

The declaration of conformity is available on request. Contact details are provided at: http://paxton.info/596