PATLITE BSV User Manual

4263-B

V95100136

Slim Model MP3 Voice Annunciator

Instruction Manual

[ TYPE : BSV ]

Thank you for purchasing the Slim Model MP3 Voice Annunicator for you application. Please read these instructions carefully before installation, maintenance and repair. Store this manual in a safe place for future reference. If you have any questions regarding this product, please contact our PATLITE Sales Representatives.

Notice for Safe Operation

In order to prevent any damage to the user and other personnel or to assets, note the following:

■The warning indications are divided into the following classes according to the degree of danger

or damage incurred when the warning is not taken into consideration and the product is not correctly used.

Warning

Caution

PLEASE

NOTE

Indicates an imminently dangerous condition : failure to follow the instructions may lead to death or serious injury.

Indicates a potentially dangerous condition: failure to follow the instructions may lead to slight injury or property damage.

Indicates something to observe before using this product. The disregard to this indication may lead to product malfunction or failure.

Notice regarding supplementary information or convenient explanation is indicated.

1. To operate this product properly, observe the following:

WARNING

●

Be sure the power is disconnected before wiring or installing this product. Possibility of electric shock

may occur.

●

Do not disassemble or modify this product. Possibility of fire or electric shock may occur. If repair is

needed, refer to [8. Before Requesting Repair]. For questions concerning our product or for when repair is necessary, refer to the end of this document for contacting your nearest PATLITE Sales Representative.

●

Be careful not to miswire this product. Possible miswiring can cause product failure or fire.

●

Be sure to stay within the operating voltage range. Possibility of fire, failure or malfunction may occur.

●

Request the installation and wiring be performed by a professional contractor. Otherwise, there is the

possibility that fire, electric shock or falling from high places may result.

CAUTION

● To protect the power supply and other internal circuitry, be sure to connect an external fuse.

●

Do not install the product in a location where vibrations exceeding the specifications exist. If installing

where vibrations do exist, install the product in the upright position to prevent the risk of product detaching and it falling, causing injury to a passer-by, etc.

Contrary to Warnings and Cautions indicated in this document, product failure due to mishandling, dissasembly, modifications or natural disasters, etc. is not covered by any Warranty. Moreover, avoid any applications outside those indicated in this document.

PLEASE

●

Do not use in an environment exposing strong radio waves or inductance noise. Noise may be

induced from the speaker horn causing malfunction or failure.

●

Do not use in an environment where corrosive gas is present. Possible cause of failure may occur.

●

To prevent damage from static electricity, touch hands or other body parts to metals or an earth

ground to discharge the body from static charge before handling static sensitive parts, such as the SD Card.

●

Use the recommended torque when attaching parts for installation, etc.

●

When this product is used for security purposes, it should be inspected daily. In case a malfunction

should occur, it is recommended that you use this product together with other security products.

●

Do not misplace parts, such as the terminal cover or front plate, while perfoming maintenance or

repair of the product to prevent possible damage.

- Caution on copyright Work that was recorded or copied from music CDs or other media used in public places may infringe upon copyrights and law enforcement may be imposed. When using a work that was recorded or copied from music CDs or other media, be sure to obtain permission from the author. In addition, copyright of audio/music data distributed or sold by PATLITE Corporation belongs to PATLITE. It is strictly prohibited to copy/reprint whole or partial contents of audio/music data belonging to PATLITE Corporation, or to transfer/sell such material on computer networks etc., without permission of the rightful holder.

2. Model Number Configuration

ＢＳＶ - ２４ＮＭ - Ｗ

■ Rated Voltage 24: DC 12 ～ 24 V

■ Transistor Type

N: NPN P: PNP

■ Recorded Messages

M: Pre-recorded Messages Blank: None (15 built-in Alarms)

■ Front Cover Color

W: Off-white D: Dark Grey S: Silver

3. Part Names

Volume

O-ring

Mounting Screw

Front Cover

Air Vents

Accessory: M3X6 Tapping Screw

Installation Bracket

SD Card Slot

(Cover Locking Screw)

Power/ Signal Wiring

Cover Locking

Hole

Front Cover Exploded View

SD Card

Model：SDV-128P (Sold Separately)

※ Patlite Corporation is a member of

the SD Card Association.

4. Installation

This product can be panel or wall mounted. Please attach in accordance with the procedure for mounting after removing the front cover.

4-1. Front Cover

When installing or adjusting the volume control to this product, please open and close the front cover in the following manner.

① Turn the front cover in the counter clockwise direction 45 degrees. ※ Assure there is ample rotation

space available for the front cover when mounting.

② When attaching for wall-mounting, pull the front cover forward to remove, then pull-out the mounting

screw and O-ring. (Refer to "3. Part Names" for the Front Cover Exploded View)

③ Please attach the removed parts in steps ① and ② in the reverse order to reassemble. Attach the

front cover so that the "�UP" is on top. (Mounting Screw Recommended Torque: 0.3 N-m)

● Use the M3X6 tapping screw (Cover Locking Screw-included) indicated on the lower-right figure to fix

the front cover. (Recommended Torque: 0.3 N-m)

+0.7

-0

�57.5

Volume

Mounting Screw

±0.2

[mm]

4-2. Panel Mounting

① Mount on a flat surface with a panel thickness of 1 mm to 3.5 mm for proper clamping. (Refer to the

② Rotate the front cover counter-clockwise 45 degrees, then loosen and remove the mounting screws. ③ Check that the mounting bracket is in position (A) before inserting the product from the front, and

④ Check that the product has been properly clamped before placing the front cover back on.

4-3. Wall Mounting

① Mount on a flat surface with a panel thickness of 1 mm to 3.5 mm for proper clamping. (Refer to the

② Rotate the front cover counter-clockwise 45 degrees, then loosen and remove the mounting screws

③ Allign the front cover with the hole positions, inserting the product from the front; insert the mounting

④ Ensure the product is properly installed before installing the front cover.

(100)

"Panel-mount Dimension drawing")

secure it with the mounting screws, clamping the mounting nut to the rear of the mounting surface. (Recommended torque: 0.3 N-m)

�68 mm

Panel Mounting Dimension Diagram

※ Conforms to IEC-61554 (DIN-43700)

"Panel-mount Dimension drawing")

and O-rings.

screws from the back panel and tighten. (Recommended torque: 0.3 N-m)

[mm]

Wall Mounting Dimension Diagram

(Product Front View)

Attach the front cover so that the arrow is alligned as indicated.

Open

Loosen (A)

2-�3.5

Installation Surface

Tighten (B)

Section

Cover Locking Screw

Cover Locking

Hole

Section C Rear View

Loosen (A)

Tighten (B)

WARNING

● Request the installation and wiring be performed by a professional contractor. Otherwise,

there is the possibility that fire, electric shock or falling from high places may result.

CAUTION

Be sure the power is disconnected before installing this product. Failure to comply may result in electric shock.

●

● Ensure the installation surface is sufficient enough to handle the weight of the product, and

where there is less vibration. Also, do not install onto a vehicle. Failure to comply will lead to injury or damage to the product.

● Use two screws when installing and tighten with the recommended torque. Failure to comply

may result in product failure due to falling or over-torquing.

Do not apply a heavy load to the wires. Failure to comply may result in damage due to an electric short.

●

● Do not turn the front cover more than 45o. Failure to comply may result in product damage.

PLEASE

● Install the product on a flat surface with no uneven surfaces. Failure to comply will weaken its

resistance to water and dust.

● If installing the product where vibrations exist, it is recommended to make periodic inspections

to ensure the mounting screws are properly tightened.

When installing in high places, choose a location which is accessible by a scaffold, ladder, etc., for repairs.

●

● When operating the product by controlling the power ON/OFF, be sure to include a switch by

which the power supply can be easily cut near the main power for safety.

● Do not block any air vents when installing this product.

Applying thread locking adhesive to the Cover locking screw may result in damage to the product.

●

NOTE

●

Depending on the mounting surface material, thickness and the volume of the product, a vibration sound may be generated from the mounting screws. To prevent it, take countermeasure steps by reinforcing the mounting screws.

5. Wiring

When wiring to external contacts for the signal line, use non-voltage contacts such as a relay, switch or an NPN (PNP type also available) open collector circuit. Refer to table 1 below for contact capacity.

■ Wiring Example

● BSV-24N（NPN Transistor Type）

Do not short Power(+) to the CH line. Failure do to so will result in damage to the product.

CH4

Light Green

CH3 Peach

CH2 Yellow

CH1 Sky

Blue

Power

(-)

Black

Power

(+)

White

■ Wiring Example

● BSV-24P（PNP Transistor Type）

Non-voltage Contact Circuit NPN Transistor Circuit

Do not short Power(-) to the CH line. Failure do to so will result in damage to the product.

CH4 Light Green

CH3 Peach

CH2 Yellow

CH1 Sky Blue

Power (-) Black

Power (+) White

Voltage Contact Circuit PNP Transistor Circuit

Table 1. Signal Contact Capacity

Current Capacity

Withstanding Voltage

Table 2. Recommended Fuse

Rated Voltage Rated Current

Table 3. Inrush Current Ratings

Inrush Current

Fuse

15mA or more

DC35V or more

250V

0.25A

17A

CH4

CH3

CH2

CH1

Power (-)

)

sat

Fuse

0.1mA or less 1V or less

Power (+)

CH4

CH3

CH2

CH1

Power (-)

Power (+)

Leakage Current

“ON” Voltage(V

Standard Fusion Slow-blow

WARNING

● Ensure the wiring is correct before connecting the power source. Miswiring may result in

product damage.

CAUTION

●

Be sure the power is disconnected before installing this product. Failure to comply may result in electric shock.

●

Do not strongly pull or tug at the wires. Failure to comply may result in damage or failure to the product.

PLEASE

● To protect the power supply and other internal circuitry, be sure to connect an external fuse.

● Be sure to check for proper wiring before connecting the power.

To countermeasure against interference noise, make wiring as short as possible and use shielded wires

●

whenever possible. In addition, separate any signal lines which pass along high voltage cables or is susceptible to receive induction noises. Interference may influence signal inputs and cause product malfunction.

●

If a non-voltage contact, such as a relay or switch etc., is used for the power supply line, consider inrush

current capacity when selecting the contact. If the capacity is insufficient, it will cause pitting or welding of the contacts, causing malfunction.

6. Directions for Operation

The following corresponds to the factory settings of this product according to the model and message registration contents at the time of order.

● The following applies to Model BSV-24□M-□

The factory setting is set for the “Bit Input”, and “Hold Playback” mode when registration data is loaded into the internal memory.

● When message registration is up to four (4) messages:

The factory setting is set for “Bit Input” and “Normal Playback” mode when registration data is loaded into the internal memory.

● When message registration is for five (5) messages and above:

The factory setting is set for “Binary Input” and “Normal Playback” mode when registration data is loaded into the internal memory. The MP3 data will play back properly when the proper transistor, bit/binary input with the signal input are integrated.

NOTE

● Even when starting two or more unitis simultaneously, a lag will occur during message playback.

6. Specifications

Items

Rated Voltage

Voltage Range

Power Consumption

Sound Pressure Level

Volume Control

Number of Playback Messages

Initial Registered Data

Audio File

Bit Rate

Maximum Playback Time

Internal Memory Size

Playback Startup Time

File Format

Operating Temperature Range

Storage Temperature Range

Relative Humidity

Mounting Direction

Protection Rating

Insulation Resistance

Withstanding Voltage

Vibration Resistance

Mass (±

10%)

(*1) Test Conditions: DC24V, Max. Vol., Ch 1 to 4 on, 1kHz sine wave at -1dB

Test Conditions: Placed on a 300mm2 base at a distance of 1 meter with a 1kHz sine wave at a -6dB input.

(*2)

Sound level of message will vary with the surrounding environment.

※

(*3) Values in brackets indicate available channels when sound reduction function is used

【Outer Appearance】

(mm)

87dB or less: (For Panel Mount) / 85dB or less: (For Wall Mount)

Sound Reduction Function: -1dB to -50dB range possible from the CH4 input

The following alarm data is loaded when no set messages are ordered

No. 1

Chime

Rapid Hi Lo

No. 6

No. 11

Synthesized Melody

No less than 300ms (Bootup for Signal Input and Power Input Conditions)

Panel Mount Indoors: Upright, Sideways, Inverted / Outdoors: Upright Only

Wall Mount Indoors: Upright, Sideways, Inverted / Outdoors: None (Indoor Use Only)

Panel Mount IP54 (Upright Direction Only)

Wall Mount IP20

More than 1MΩ at 500V DC between the terminals and chassis

500VAC applied for 1 minute between terminals and chassis without breaking insulation

□75

Bit Input: 5 (4) / Binary Input: 31 (7)

No. 2

Beep

Melody Chime

No. 7

No. 12

Call Sign

Maximum Playback Time: 63sec (at Standard Bit Rate)

Recommended SD Card: SDV-128 (Sold Separate)

70m/s2 at 30Hz in the X, Y and Z directions for 2 hours each

19.9

Specifications

DC 12 to 24V

DC 10.8 to 26.4V

Max. 3.5W

Volume Adjustable

No. 3

No. 8

No. 13

MPEG1 Audio Layer III (MP3)

32kbit/s, 64kbit/s, (Standard Rate)

508kB (MP3 data total)

SD Card Format: FAT16

-10

-20

85% RH or less (No Condensation)

71.5

AWG #22 UL1007

(*1)

Stutter

Synthesized Piano

Inverted Reveille

C to +50oC

C to +60oC

100g

67.6

No. 4

Bell

Synthesized Bell

No. 9

No. 14

Galactic Motor

(*3)

500

5mm Sleeve

No. 5

Yelp

Stutter + Bell

No. 10

No. 15

Two Tone

(*2)

NOTE

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undersired operation.

● Despite the cautions and warnings provided in this manual, it is not the responsibility of PATLITE for

any failure or damage occured from mishandling.

● Due to changes, improvements, etc., the contents of this manual may change without advance notice.

4263-B

'11.1.AUTO