LOTUS
FCC statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on.
The user is encouraged to try to correct the interference by one of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not
expressly approved by the party responsible for compliance could void
the user's authority to operate this equipment. (Example- use only
shielded interface cables when connecting to computer or peripheral
devices).
FCC Radiation Exposure Statement
This equipment complies with Part 15 of the FCC Rules.Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Channel
This equipment marketed in USA is restricted by firmware to only
operate on 2.4G channel 1-16.
PT-61L008
Getting Started Guide
Important Ergonomic Information
Long periods of repetitive motions using an improperly
set-up workspace, incorrect body position, and poor work
habits may be associated with physical discomfort and
injury to nerves, tendons, and muscles. If you feel pain,
numbness, weakness, swelling, burning, cramping, or
stiffness in these areas, see a qualified health professional.
Installation of the Mouse
The USB receiver fits into the bottom of the mouse for
storage.
• Insert the 2 AAA batteries into the mouse
• Simply plug your receiver into an open USB port to
begin using
your mouse. Note: for convenience and portability the
receiver stores
in the bottom of your mouse when not in use.
Connecting the Mouse with the Receiver
1. Press the button on top of the receiver.
2. Press the connect button on the bottom of the mouse.
Low Battery Light
The low battery indicator on top of your mouse will blink red
to indicate that the battery needs to be replaced. To extend
battery life place the receiver in the bottom of the mouse
when not in use. This will automatically turn your mouse off.
Troubleshooting
If your Wireless Mouse does not function properly, please
review the following steps for troubleshooting.
• Insure that the USB mini-receiver is properly inserted
into your computer’s USB port. Try another USB port.
• Keep the mouse within one meter (3 feet) of the
receiver.
Metallic surfaces will shorten transmission distances.
• Try re-connecting the mouse with the receiver.
• If you find you are having problems (erratic or no
movement) or if
the low battery light blinks red, you will need to replace
the batteries.
Maintenance of your Mouse
• You may clean the surface of the Mouse with a soft
damp cloth.
• Do not use any harsh or abrasive cleaners.
• Before using any chemical cleaners, please test the
results on the bottom of the device.
International Standards and Safety
INVISIBLE LASER RADIATION: DO NOT VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS; CLASS 1M
LASER PRODUCT. This optical device complies with
International Standard IEC 60825-1: 2001-08, Class 1M
Laser Product Invisible and also complies with 21
CFR 1040.10 and 1040.1, except for deviations pursuant to
Laser Notice Nr. 50, dated July 26, 2001: Emission of 2
diverging beams (+/-4°) of infrared user-invisible light
Maximum power 2x300uW with 2 interleaved lasers (duty
cycle 24%), wavelength range (min 844, max 865
nanometers) Operating temperature between 0°C (32°F) to
40°C (104° F). CAUTION: This optical device has no
serviceable parts. Use of controls or adjustments or
performance of procedures other than those specified
herein may result in hazardous radiation exposure.
Guidelines for safe and efficient use. A Class 1M Laser
Product is safe under reasonably foreseeable conditions of
operation, but may be hazardous if the user employs optics
within the beam. It is recommended to observe the
following precautions:
1. Viewing the laser output with certain optical instruments
(for example, eye loupes, magnifiers and microscopes)
within a distance of 100mm may pose an eye hazard.
2. Do not direct the infrared beam at anyone's eye.
3. In the absence of proper operation and if troubleshooting
is unsuccessful, switch off the device and call Logitech
technical support. 4. Do not attempt to disassemble your
product unless it is for end-of-life disposal.
5. Do not expose your product to liquid, humidity, or
moisture. 6. Do not operate your product when the
temperatures is outside the specified operating range of
0°C (32°F) to 40°C (104° F). In case
of exposure to out-of-range temperature environment,
switch off the device, and allow temperature to stabilize
within the specified operating temperature range before
operating.
Loading...