Paslode CF-325 User Manual

Model CF-325

9

902245-3

21

01/09

Introduction and Warranty

Paslode Cordless Framing Nailer
Operating Manual

This manual is intended to acquaint you with the Paslode
Cordless Framing Nailer. Unlike other power fastening
tools, the Cordless Framing Nailer is powered by an
internal combustion linear motor. In simpler terms, your
Cordless Framing Nailer is powered by a motor similar to
the one that powers an automobile. The Cordless
Framing Nailer ignites a fuel and air mixture to produce
the energy to drive the motor, which in turn drives the
fastener. As you will see, the Cordless Framing Nailer is
totally self-contained. It carries its own fuel supply and
battery, along with a supply of fasteners.

For ease of use, this manual is divided into sections (see
Contents). Each section of the manual is written with you,
the tool operator, in mind. We have left out all of the
technical terms so that you can readily understand how
to get the maximum performance from your Cordless
Framing Nailer, and how to avoid damaging the tool or
injuring yourself. But, to accomplish this, we need you to
do two things:

1. READ THE MANUAL FROM COVER TO COVER
BEFORE USING THE TOOL.

2. FOLLOW ALL INSTRUCTIONS IN THE MANUAL.

The Cordless Framing Nailer should be handled like
other power fastening tools that you use. Like most tools,
when used improperly it could result in injury. If you are
going to allow others to use the Cordless Framing Nailer,
it is your responsibility to make sure that they also read
and comply with the instructions in this manual before
attempting to operate the tool.

Should you have questions about the Cordless Framing
Nailer, or wish to obtain additional copies of this manual,

®

please contact your Paslode

representative. The space
below is provided so that you may record your
representative's name, address, and telephone number.

My Paslode representative is:

Name

Address

piZ etatSytiC

Telephone Number

Paslode®Cordless CF325 Warranty and Limitations

Paslode warranties that new Paslode Cordless power fastening
tools, parts and accessories will be free from defects in material
and workmanship for the period shown below, after the date of
delivery to the original user.

ONE-YEAR LIMITED WARRANTY

A one-year warranty will apply to all parts, except those listed
below as normal wearing parts, or parts which are specifically
covered by an extended warranty.

FIVE-YEAR EXTENDED LIMITED WARRANTY

A five-year warranty will apply to all molded nylon parts:

• Motor Housing, Cap and Grille

• Handle Halves and Actuator

• Trigger

• Magazine Parts

WARRANTY STATEMENT

This warranty is limited to tools sold and service requested in the United
States. To obtain information on warranty service in the United States,
refer to the Service Center listing that was provided with your tool.

Paslode's sole liability hereunder will be to replace any part or accessory
which proves to be defective within the specific time period. Any replacement
part or accessory provided in accordance with this warranty will carry a
warranty for the balance of the period of warranty applicable to the part it
replaces. This warranty does not apply to part replacement required due to
normal wear.

This warranty is void as to any tool which has been subjected to misuse,
abuse, accidental or intentional damage, use with fasteners, fuel, batteries,
or battery chargers not meeting Paslode specification, size, or quality,
improperly maintained, repaired with other than genuine Paslode replacement
parts, damaged in transit or handling, or which, in Paslode's opinion, has
been altered or repaired in a way that affects or detracts from the
of the tool.

PASLODE MAKES NO WARRANTY, EXPRESSED OR IMPLIED, RELATING
TO MERCHANTABILITY, FITNESS, OR OTHERWISE, EXCEPT AS STATED
ABOVE, and Paslode's liability AS STATED ABOVE AND AS ASSUMED
ABOVE is in lieu of all other warranties arising out of, or in connection with,
the use and performance of the tool, except to the extent other wise provided
by applicable law. PASLODE SHALL IN NO EVENT BE LIABLE FOR ANY
DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES, INCLUDING, BUT
NOT LIMITED TO, DAMAGES WHICH MAY ARISE FROM LOSS OF
ANTICIPATED PROFITS OR PRODUCTION, SPOILAGE OF MATERIALS,,
INCREASED COST OF OPERATION, OR OTHERWISE.

Paslode reserves the right to change specifications, equipment, or designs
at any time without notice and without incurring obligation.

performance

2

Contents

egaPtcejbuS

Introduction and Warranty ......................................................... 2

An Overview of the Paslode Cordless Framing Nailer ...............4

Safety Instructions......................................................................5

Battery and Charging System ................................................... 8

Fuel Cell and Metering Valve .................................................. 10

Preparing the Paslode Cordless Framing Nailer for Use

Paslode Cordless Framing Nailer Operation........................... 14

Fasteners and Applications ..................................................... 15

Servicing ................................................................................. 16

Troubleshooting ...................................................................... 18

.........13

The battery charger meets all safety requirements for power
tools.

is a trademark
Paslode
An Ilinois Tool Works Company
888 Forest Edge Drive
Vernon Hills, Illinois 60061

Power Nailers are made in the U.S.A. and are

protected by one or more of the following U.S. patents:*

4,403,722 4,483,280 4,483,474 4,522,162

*Other patents issued and pending.

Paslode

®

is a member of:

3

An Overview of the Paslode Cordless Framing Nailer

Description

The Paslode Cordless Framing Nailer is a self-contained,
fully portable nailer that uses liquid hydrocarbon fuel to
power a unique linear drive internal combustion motor.

As with any internal combustion motor, the Paslode Cordless
Nailer will require periodic maintenance to keep it operating
at it's peak performance. The cleaning procedure booklet
will instruct you on the proper cleaning of your tool. If
additional services are required, contact your local Paslode
service provider.

NOTE: Altitude Restriction

Paslode Cordless tools are powered by an internal
combustion engine and are effected by altitude. The
tool may lose power or not cycle consistantly at
elevations of 4000 feet or greater.

Specifications

Dimensions: Weight (with battery) 7.5 pounds

Height 14-1/2 inches
Length 12 inches

Cycle Rate: Intermittent Operation – 2 to 3 nails

per second

NOTE: Exceeding these rates could cause tool to overheat,
resulting in loss of performance or damage to tool
components.

By using the Paslode Cordless Framing Nailer at its
recommended cycle rate, you will be able to drive several
thousand nails in a typical workday.

Fasteners: 30° paper tape collation

Minimum 2 inch x .113 diameter shank
Maximum 3-1/4 inch x .131 diameter shank

Magazine Capacity: 1 nail strip + 5 fasteners.

Battery : 6 volts DC - Provides enough energy to

drive approximately 4000 fasteners on a full
charge.

Fuel Cell: Orange quicklode™ fuel cartridge (1.32 oz)

Liquid hydrocarbon - Provides enough fuel
to drive approximately 1200 fasteners.

Motor Housing

MOTOR ASSEMBLY

Adjustable

Work-Contacting

Element

Toe Nailing Teeth

Cover and Filter

Fuel Cartridge Compartment

Battery
Indicator Light (LED)

Battery
Compartment
(Opposite Side)

Utility Hook

HANDLE ASSEMBLY

Channel magazine

Trigger

Follower

4

The following safety instructions have been included in this
booklet to provide you with basic information necessary for
safe operation of the Paslode Cordless Framing Nailer. DO
NOT ATTEMPT TO OPERATE THIS TOOL UNTIL YOU
HAVE READ AND UNDERSTAND ALL SAFETY
PRECAUTIONS AND MANUAL INSTRUCTIONS.

In addition to these instructions, training may be necessary.
Contact your Paslode representative for additional
information.

WARNING

Safety Instructions

WARNING

Never expose or store the
tool, fuel or battery at
temperatures in excess of
120° F (49° C). Fuel and/
or the battery may burst,
releasing flammable gas.

The Paslode Cordless
Framing Nailer is an
internal combustion
device. It produces hot
exhaust gases that may
ignite flammable
materials. Never use the
tool in a combustible
environment or in the
presence of combustible
materials, such as
flammable chemicals,
adhesives, gasoline, or
solvents.

WARNING

Never attempt to operate
this tool until you have
read and understood all
safety precautions and
manual instructions.

Failure to follow all safety
precautions instructions
may result in a permanent
loss of vision, serious
personal or even fatal
injury, property damage
and/or tool damage.

WARNING

This tool must be operated

only in a well-ventilated
environment, because

the tool exhausts carbon
monoxide similar to a gas
chainsaw or lawnmower.
Exposure to carbon
monoxide from use in
eclosed areas, may cause
dizziness, nausea, or
unconsciousness or
death.

WARNING

ALWAYS keep the
Cordless Framing Nailer,
fuel cartridge, battery cell
and battery charger out of
the reach of children.

5

Safety Instructions

WARNING

EYE and EAR safety gear
must be worn when
working with or in the
vicinity of the Paslode
Cordless Framing Nailer.

1. Eye protection must meet the requirements of ANSI
Standard Z87.1 and should have side shields for
increased protection. As an employer you are
responsible for enforcing the use of eye protection
equipment by the tool operator and all personnel in the
work area.

2. NEVER ASSUME THE TOOL IS EMPTY.

Never point the tool at yourself or anyone else.

3. NEVER ENGAGE IN "HORSEPLAY" WITH THE TOOL.

The Cordless Framing Nailer is not a toy – it is a tool.
Careless and improper use may result in a serious
accident.

7. NEVER OPERATE THE TOOL WITH THE WORK
CONTACTING ELEMENT REMOVED OR DISABLED.

This device helps reduce the possibility of accidental
fastener discharge by preventing the tool from operating
until it is completely against the work surface.

NEVER operate the tool if the work contacting element
is not working properly.

8. ALWAYS POINT THE TOOL AWAY FROM YOURSELF
AND OTHERS WHEN CLEARING JAMS OR
REMOVING FASTENERS. REMOVE THE FUEL
CARTRIDGE AND BATTERY.

Pull the follower slightly back and push the release
lever. Tip the tool nose up slightly and fasteners should
slide out of the rear of the magazine. If fasteners are
jammed, refer to the appropriate servicing section of
this manual.

9. NEVER OPERATE THE CORDLESS FRAMING
NAILER IF PARTS ARE LOOSE, DAMAGED OR
MISSING.

10. NEVER DRIVE FASTENERS INTO KNOTS OR ON
TOP OF OTHER FASTENERS.

A fastener may ricochet and cause serious injury.

4. NEVER CARRY THE TOOL WITH YOUR FINGER ON,
OR SQUEEZING, THE TRIGGER.

This practice may result in the accidental discharge of
a fastener.

5. NEVER OPERATE A MALFUNCTIONING TOOL.

Refer to the servicing or troubleshooting section of this
manual to correct the problem. If the problem cannot be
corrected, stop using the tool and report it to your
supervisor or Paslode representative.

6. DO NOT LOAD FASTENERS WITH THE TRIGGER
AND/OR WORK CONTACTING ELEMENT PRESSED
IN. A fastener may be accidentally discharged.

11. OPERATE THE TOOL ONLY ON THE WORKPIECE.

WARNING

The Cordless Framimg
Nailer must be operated
only when it is in contact
with the work surface.
When fastening thin
materials such as
plywood, be sure to
position the tool so that
the fastener is driven into
the underlying piece.

6

Safety Instructions

12. NEVER DRIVE FASTENERS INTO AREAS WITH
CONCEALED HAZARDS.

Always check the area behind the work surface for
electrical wiring, gas pipes, water pipes, sewer drains or
other potential hazards.

13. ALWAYS MAINTAIN SECURE AND UNOBSTRUCTED
FOOTING WHEN ON LADDERS, PLATFORMS OR
OTHER HIGH LOCATIONS.

WARNING

Never over-reach, since
tool recoil may cause a
loss of balance. Always
be aware of edges and
drop-offs when nailing on
rooftops and other high
locations. Keep them in
full view.

14. ALLOW ONLY QUALIFIED PERSONNEL TO OPERATE
THE CORDLESS FRAMING NAILER.

15. PROPERLY STORE FUEL CELL.

WARNING

Always store tool, fuel
cartridge and battery
where they will not be
exposed to an open flame,
sparks or temperatures
above 120° F (49° C).

16. ALWAYS STORE THE TOOL WITH THE FUEL
CARTRIDGE AND BATTERY REMOVED.

Store the fuel cartridge in the case with the Cordless
Framing Nailer.

17. KEEP THE TOOL CLEAN AND WELL MAINTAINED.

A clean tool is less likely to jam or malfunction.

18. KEEP YOUR HANDS CLEAR OF THE WORK AREA
SURFACE.

WARNING

WARNING

Only persons who have
read and fully understand
all tool operation, safety
and maintenance
instructions should be
allowed to operate the tool.

Battery Disposal:

The Paslode Cordless batteries contain cadmium and must be recycled or disposed of properly. It is illegal in some
areas to place a nickel-cadmium battery into the trash or solid waste stream. You may contact your local recycling
center for information on where to return the spent battery or call 1-800-822-8837 for information on Ni-Cd battery
recycling in your area.

A fastener may exit at an
angle unexpectedly and
cause injury.

7

Battery And Charging System

The Paslode Cordless tool comes with a rechargeable
battery and its owncharging system.This charging system
is the only one that will work with all Paslode batteries
(round or oval). It will accept either the round or oval
shaped batteries. The first step in preparinganew tool for
operation is to fully charge the battery. New batteries are

shipped discharged and must be charged prior to first
use. Batteries will take5minutes to2hours (time will be

dependant on theamount of discharge within the battery) to
recharge.

Important Charging Notes

WARNING

CHEMICAL/EXPLOSION
HAZARD

ReadALLinstructions before
charging or using battery.
Failure to follow ALL
instructionsmayresultinfire,
severe burns, or release of
toxic materials.

Battery Disposal:

The Paslode batteries contain cadmium and must be
recycled or disposed of properly. It is illegal in some
areas to place a nickel-cadmium battery into the trash or
solid waste stream. You may contact your local recycling
center for information on where to return the spent battery
or call 1-800-822-8837 for information on Ni-Cd battery
recycling in your area.

Charging Instructions:

1. Remove wall mount unit with the orange label from
the tool case and plug into a 120V AC outlet. Set
orange charger on a stable surface and insert the
wall mount unit's plug into the plug receptacle on the
back of the charger (see picture). A green light
indicates power is on and charging system is ready.

2. Remove the battery from tool or case and insert
terminals down into charger. The red light will come
on indicating that the battery is charging and the
green light will go out.

NOTE

If battery is completely discharged the red light and
the green light may flash back and forth for up to
20 minutes. This safety feature slowly recharges
the battery until it is ready to accept the full charging
current. If the red and green lights continue to
flash after 20 minutes, replace the battery.

3. After charging, the red light will go out and the green
light will come on, indicating that the battery is fully
charged. The charger will keep the battery at full
charge until it is removed.

4. Unplug the wall mount unit from the charger and
remove the wall mount unit from the 120V AC outlet.

Charging Times:

First charge (new battery) 2 hours

Discharged Battery 5 minutes to 2 hours

Wall Mount Unit

Plug

THE PASLODE BATTERY CHARGING SYSTEM

8

REAR VIEW OF

CHARGER BASE

Plug Receptacle

Charger
Base

Charging Don'ts:

1. Never charge battery outdoors or in temperatures
below 40 F (5 C).

2. Never allow metal objects to come in contact with
battery terminals.

3. Never puncture or attempt to open battery case or
cells.

4. Never store battery where it will be subjected to
temperatures above 120 F (49 C).

5. Never incinerate battery.

6. Never use a defective battery charger, one that
overheats and/or smokes when plugged in.

7. Never immerse the battery in water.

Charging System Accessories:

Battery Charger Kit - Part No. 900200
Wall Mount Transformer* - Part No. 900477
Battery Charger Base* - Part No. 901230
Automotive Adapter* - Part No. 900507

Inserting Battery

Battery and Charging System

Battery Indicator Light

The illustration is a close-up of the side of the Paslode
Cordless framer handle. On the side of the handle is a small
plastic lens. This is the battery indicator light.

When you insert a fully-charged battery into the tool, you will
see a blinking green light. If the light blinks red, recharge the
battery.

Battery Indicator
Light

1. Load the battery, contacts first, into the Cordless
Framing Nailer.

2. Push battery fully forward into its locked position.

3. To remove battery, push down on locking tab and slide
battery out.

NOTE: If battery is left in tool for an extended period, the
battery will discharge completely and will require recharging.

IMPORTANT: Should your battery terminals become
corroded and cause poor electrical contact, clean the
terminals using a cloth or pencil eraser.

Clean the
Contacts

9

Quicklode™ Fuel Cartridge

Fuel Cartridge

WARNING

EXPLOSION/FIRE
HAZARD

Read ALL safety
instructions before using
or handling the fuel cell.
Failure to follow ALL
instructions may result in
explosion or fire. This
may cause serious
personal injuries or
property damage.

Keep the fuel cartridge
away from heat, sparks
and open flame. Do not
smoke when handling or
operating tool or fuel
cartridge.

Exposure to
temperatures above
120°F (49°C) may cause
the fuel cartridge to
burst, releasing
flammable gas.

There is a second container inside the fuel cartridge. The
inner container holds the fuel. The space between the inner
container and the outer cylinder is filled with a gas, called the
propellant, which is under pressure.

To eject the fuel, propellant pressure squeezes the inner
fuel container, much as you squeeze a tube of toothpaste.
This squeezing action ensures that all the fuel is used, and
that the Cordless Framing Nailer can operate in any position.

Because of this container-within-a-container design, you
might hear the sound of fluid when shaking the fuel cell after
all the fuel has been used. This is the propellant, which
remains between the containers even after all the fuel has
been expelled.

If you expose the empty fuel cartridge to extreme
temperatures, the propellant gas will expand and could
cause the container to burst, releasing flammable gases.

The fuel contains a small amount of oil to keep the tool
lubricated during use. It is not necessary to oil the tool
during normal operation. When cleaning the tool, use only
Paslode Cordless tool oil. Using oils not formulated for the
Paslode Cordless Tool, may cause loss of power and may
damage the internal parts of the tool's motor.

WARNING

Sunlight can raise the inside temperature of an
unventilated motor vehicle or storage container to
above 140°F (60°C).

Never puncture or attempt to open the fuel; it is
nonrefillable.

Never incinerate, reclaim or recycle the fuel.

Never smoke while installing or operating the fuel
cartridge or tool.

Never inhale the spray.

Keep out of the reach of children.

Store fuel cartridge(s) in well-ventilated areas only.

10

NOTE

1. Never attempt to refill the cartridge! Replace
with fresh fuel cartridge, and dispose of spent

cartridge properly.

2. Do not attempt to remove or reuse the fuel

cartridge cap.

3. When replacing fuel cartridge also clean or replace
air filter for optimum tool operation.

NOTE: Altitude Restriction

Paslode Cordless tools are powered by an internal
combustion engine and are effected by altitude. The
tool may lose power or not cycle consistantly at
elevations of 4000 feet or greater.

Quicklode™ Fuel Cartridge

etaD yB desU tseBpac egdirtrac leuF

NOTE:

Paslode Cordless fuel cartridges are marked with a best used by date on the bottom of the can.

For maximum performance use fuel before best used by date.

DANGER

Paslode Cordless Fuel Cartridges are flammable.
Do not smoke when installing the metering valve!

Paslode Cordless Fuel Cell/Cartridge Disposal Guidelines

Paslode the industry leader in cordless technology provides this information to assist users with the proper disposal of discarded
fuel cells/cartridges. Acceptable disposal options vary depending on the type of fuel cell/cartridge users. All users must consider
federal, state and local solid waste regulations to ensure that discarded fuel cells/cartridges are disposed of properly. Users must
contact their local solid waste authority for further guidance.

Discarded fuel cells/cartridges (used or unused) may be considered hazardous waste under the Resource Conservation and
Recovery Act (RCRA) depending on several factors as described in the paragraphs that follow. Upon disposal used and unused
fuel cells/cartridges may be classified as ignitable hazardous waste (waste code D001) under U.S. EPA regulations.

Hazardous waste generated by homeowners and contractors who perform routine maintenance for homeowners in their homes are
not regulated by RCRA. In general, "household wastes" generated by homeowners and their contractors are exempt from hazard­ous waste regulation because those wastes are expressly excluded from the definition of hazardous waste. For example US EPA
has excluded as "household waste" aerosol cans that contain residual product and propellent. Thus under federal hazardous waste
regulations homeowners and contractors may dispose of discarded fuel cells/cartridges as general refuse in a properly permitted
municipal landfill. These users must still contact their local solid waste authority to determine if any
prohibits or restricts such disposal.

state or local regulation

Paslode takes no responsibility for proper fuel cell/cartridge disposal. Proper disposal remains the responsibility of sellers and
users. All sellers and users must contact their local solid waste authority to determine if any federal, state or local regulation
prohibits or restricts disposal. Users may obtain more information about U.S. EPA hazardous waste regulations at the following
internet address: www.epa.gov/epaoswee.osw/hazwaste.htm

Alternatively users may contact U.S. EPA's RCRA Superfund Call Center at 1-800-424-9346 to receive more information.

11

Quicklode™ Fuel Cartridge

Inserting Fuel Cartridge

A. Inserting the fuel cartridge into the Cordless Framing
Nailer is very simple. To begin, press up at the bottom of the
actuator cover and pivot outward to open. The cover will
swing out of the way.

1. Press Up

2. Pull Out

B. Lift the fuel cartridge adaptor and insert the Quicklode
fuel cartridge into the tool.

C. Release the adaptor so it is centered on the fuel
cartridge.

D. Close the actuator cover to complete the loading of fuel
in the Cordless Framing Nailer. Do this by swinging it up
and over the fuel cartridge, and pushing down until the
actuator cover snaps into position.

12

1. Swing Up

2. Push Down

Preparing the Paslode Cordless Framing Nailer for Use

Fasteners

The Paslode Cordless Framing Nailer drives Paslode
RounDrive®nails, which have been collated into strips. The
use of nails that do not meet Paslode standards could cause
tool damage and void your warranty. Paslode nail sizes and
types are illustrated in the Fasteners and Applications
section.

Loading Fasteners

STEP 1: To load, pull the follower handle back to the rear
lock position (button will pop up).

STEP 2: Insert a strip of nails and release follower by
pushing on button.

Lockout Feature

The purpose of this feature is to prevent needless
blank cycling,which could waste fuel and damage
tool components. Five (5) nails will be left in the
magazine when the follower reaches the lockout
area. The indicator arrow shows that you can reload.
It does not indicate that the Cordless Framing Nailer
is empty. Because of a lockout feature in the
Cordless Framing Nailer it will not operate when the
nail supply in the tool is less than six (6) nails.

Paslode Cordless Framing Nailer and
Outdoor Weather

Use the Cordless Framing Nailer outdoors, in clear weather,
when the nailer, fuel cartridge, and battery are between
20°F (-7°C) and 120°F (49°C.

HOT WEATHER OPERATION

The Cordless Framing Nailer requires cooling of the motor
assembly to operate properly. The fan normally provides
the necessary air flow to permit continuous operation.
Whenever the Cordless Framing Nailer is idle for extended
periods, keep the fuel and tool out of direct sunlight and in
surroundings where temperatures will not exceed 120°F
(49°C). After extended periods of continuous use, it may be
necessary to cool the motor by setting tool aside for 10-15
minutes or until the tool operates normally. An overheated
tool may not drive nails completely or may operate erratically.

There is a reload indicator on follower and tool. A full strip
can be loaded in this area as shown above.

COLD WEATHER OPERATION

Fuel at cold temperatures lose the required propellant force.
Bring the tool, battery, and fuel cartridge above minimum
operating temperature without direct exposure to flame, and
check the battery.

CAUTION

The Cordless Framing Nailer should not be used in the
rain or where excessive moisture is present. The use
of the Paslode Cordless Technology under these
conditions may result in damage to tool components
and cause tool to malfunction.

13

Paslode Cordless Framing Nailer Operation

PRESS WORK –
CONTACTING
ELEMENT
AGAINST THE
WORK SURFACE.

Fan motor starts,
fuel is injected into

Note: The fan will run for
approximately 10 seconds
after the last nail is driven

combustion
chamber and
mixed with air by
the fan.

SQUEEZE
TRIGGER
Spark plug sparks
and fuel/air mixture
ignites.
Combustion
powers piston
assembly driving
fastener.

LIFT TOOL ­RELEASE
TRIGGER
Combustion
chamber opens.
Fan exhausts hot
gases and cools
internal
components.

DANGER

Move up to Increase

Drive Depth

Move Down to Reduce

Drive Depth

Probe Stop

Depth of Drive Adjustment

Remove the battery before adjusting the depth of drive.

The depth of drive adjustment is made by adjusting the work
contacting element. Pulling the probe stop outward away
from the tool will allow the work contacting element to be
moved up or down.

If the tool is over-driving (the nail head is driven below the
surface of the wood), the work contacting element should be
moved down slightly. If the nails stand up (the head is not
flush with the work surface), the work contacting element
should be moved up slightly. The indicator marks are set at
1/10" increments with a total range of 1/2".

Standard

Work-Contacting

Element

The work contacting element and nose will become hot
after prolonged or rapid use. If it becomes necessary to
adjust the work contacting element, avoid touching with
bare hands.

Push

Adjustable Utility Hook

The adjustable utility hook can be used as a belt or
rafter hook. To adjust the utility hook, push the black
button in the direction of the arrow and rotate it to the
desired position.

14

Adjust the work contacting element to get the nail head
depth to meet job requirements.

No-Mar Work-Contacting Element

For applications where the work-piece must be mark free,
like in siding and recreational decks, order the No-Mar
Work-Contacting Element, Part No. 901252

DANGER

Never attempt to operate the Cordless Framing Nailer
unless both adjustment screws are installed. Intentional
removal of an adjustment screw could result in improper
tool operation, loss of nail control and injury to tool user
or bystanders.

Fasteners and Applications

SIZE TYPE APPLICATION

2" x .113 (6D) Common Ring Shank Underlayment, wall sheathing,

2" x .113 (6D) Common ring shank, Fencing, siding

2-3/8" x .113 (8D) Cooler ring shank Roof & floor decking, underlayment,

2-3/4" x .113 (8D) Coated ring shank, Recreational decking, siding, fencing

3" x .120 (10D) Coated nail Remodeling
3" x .120 (10D) Ring shank, hot-dipped Fencing, recreational decking, siding,

3" x .131 (10D) Coated nail Framing
3-1/4" x .131 (12D) Coated nail Framing

Smooth Shank - For general construction, carpentry and
framing: the most popular and versatile.

hot-dipped galvanized plus

hot-dipped galvanized plus

galvanized plus tile roofs

Hot Dipped Galvanized Plus - These nails are hot dipped
with a baked on polymer coating. They offer the highest

roof and floor decking, siding

sheathing

corrosion resistance of any galvanized nail. These nails

Ring Shank - The ring shank provides improved withdrawal
resistance for applications where the resistance from smooth
shank fasteners is not adequate: floor decking, crating,
pallets.

Hardened Steel - For attaching wooden plates to green
concrete foundations; 2X furring strips to cinder block.

should be used where higher corrosion resistance is required
to retard rust and rust staining. Recommended for use in
natural wood siding, such as cedar, redwood, cypress and
preservative treated lumber. (Not for use in all-weather
wood foundations.)

The Paslode Cordless Framing Nailer is not recommended for use with 3"
Ring Shank nails in pressure treated lumber.

15

Servicing

Restrict Field Service to the Following

CHECKING THE ENERGY LEVEL OF THE BATTERY

RECHARGING THE BATTERY

CHECKING THE FUEL CARTRIDGE

REPLACING THE FUEL CARTRIDGE

CLEANING THE AIR FILTER

CLEARING A JAM

Attempts to go beyond these procedures could result in
serious personal injury or damage to the Cordless Framing
Nailer and voiding the warranty.

There are certain problems you may encounter when you
are using the Cordless Framing Nailer that you will be able
to correct on the work site. The following field service
procedures are the only service procedures you should
attempt. Anything else that may appear wrong with the
Cordless Framing Nailer should only be diagnosed and
repaired by a fully trained service technician. If you have any
reason to believe that your problem is beyond the service
procedures in this manual, contact your Paslode
representative immediately.

DANGER

Never attempt any maintenance of the Paslode Cordless
Framing Nailer without first removing the fuel cartridge
and battery. Maintenance should be started only after
the tool is completely inoperative.

Battery Check

Periodically check the battery indicator light in the handle
of the Cordless Framing Nailer. When encountering a
problem, the first step should always be to make sure the
battery has enough energy to operate the tool.

Fuel Cartridge Check

If the Cordless Framing Nailer's fan operates and the light
is green, but the tool will not cycle or does not drive
fasteners completely, check the fuel cartridge. With the fuel
cartridge out of the tool, check to see if the cartridge still
contains fuel. To determine if there is any fuel left in the fuel
cartridge, hold in the upright position and simply place
against a solid object, and gently push about three or four
times. A small amount of fuel should be released each time.

DANGER

Wear safety glasses when performing this test. Never
perform this test near an open flame or sparks, while
smoking, or where the fuel may get into your eyes.

If fuel is not released with each operating of the cartridge
cap, this indicates that there is no more fuel left in the
cylinder and it must be replaced. Dispose of the empty fuel
cartridge properly.

Clearing a Jam

An occasional problem you may encounter is a jammed
fastener. Because of the unique design of the Cordless
Framing Nailer, clearing a jammed fastener is easy:

1. Remove the fuel cartridge and battery.

2. Lock follower back in magazine and remove fasteners.

3. Loosen the (2) magazine mounting screws with the
5/32 hex key.

4. Pull handle/magazine away from the nose of the tool
and clear jam.

5. Realign handle magazine to nose, and tighten mounting
screws.

6. Reload fasteners and release follower.

When the work contacting element is pressed on work
piece, the fan motor will turn on and blinking green light will
turn solid green. If the light blinks red or glows red, recharge
battery.

16

Remove

Servicing

WARNING

Make certain magazine mounting screws are tight and
magazine is tight to nose. Attempting to fire tool with a
loose magazine will result in loss of nail control,
damage to tool, or nail discharge toward operator.

Air Filter

Open the grille by pressing slightly above the adapter, and
pivoting the cover open. The air filter simply lifts out.

Tap the filterGENTLY to remove any dust.Check and clean
the air filter every two days. Soap and water restores the
filter to a "like new" condition.

Grille

Filter

When you get home:

1. Place the battery in its charger if it needs charging as
indicated by the red charge light on the handle.

2. Wipe your Cordless Framing Nailer withaclean, soft
cloth.

3. Remove and clean the filter every two days.

Tool Cleaning and Oiling

Periodic cleaning and oiling are necessary to keep the
Paslode Cordless Nailer operating properly. The tool
should be cleaned and lubricated at least every 50,000
cycles. This number may vary depending upon the rate
at which the tool is used and the operating conditions it
is used in. The chart in the cleaning instructions will help
you determine how often the tool should be cleaned.

Cordless Framing Nailer Paslode
Cordless Tool Accessories

End-of-Workday Routine

At the end of each workday, conduct an end-of-workday
routine. These simple steps are based on maintaining the
safety and operational efficiency of the Paslode Cordless
Framing Nailer.

Before you leave the work site:

1. Remove battery and store in tool case. Always use the
Cordless Framing Nailer case for transporting and

storing the tool.

A variety of accessories are available for the Paslode
Cordless Framing Nailer:

No-Mar Work Contacting Element - Part No. 901252

Battery - Part No. 404717

Clear Safety Glasses - Part No. 402510

Paslode Lubricating Oil - Part No. 401482

Battery Charger Kit - Part No. 900200

Wall Mount Transformer - Part No. 900477

Battery Charger Base - Part No. 901230

PaslodeCordless Framing Nailer Case-PartNo. 404710

Automotive Adapter - Part No. 900507

Contact your Paslode®representative for additional
information.

Tools

2. Dispose of all empty fuel cartridges. Remember to

dispose of these cartridges where they will not be found
by children, crushed, punctured, or burned.

A 5/32 Hex Socket Wrench (Part No. 401331)is provided
with each Paslode Cordless framer.

17

Troubleshooting

Preparing Tool for Operation - Battery/Charger Problems

SYMPTOM POSSIBLE PROBLEMS SERVICE

Battery does not appear to accept charge
when the battery and charger are plugged
into the wall mount adapter.

Battery charger flashes red/green for more
than 20 minutes.

Inoperative indicator lights on charger, or
defective charger.

Defective battery.

Try battery in tool after a full charge cycle. If
tool LED is green, charger is not working
properly. Replace charger, or monitor
charging time to ensure battery has
adequate time for recharging. It is normal
for battery to feel warm after properly
charging.

Charger gets hot, makes excessively loud
noise, or smokes during charging cycle.
Charger cord or wall plug gets hot.

Normal Stage of Operation

SYMPTOM POSSIBLE PROBLEMS SERVICE

Fan does not run - tool indicator light is
blinking red or solid red.

Fan does not run, or runs slower than
normal - tool indicator light is solid red.

Work-contacting element does not depress
fully - tool does not operate.

Tool will not cycle - fan runs, indicator light
is solid green.

Battery damaged or cycle life exhausted.

Damaged charger.

Battery is not charged.

Battery terminals are oily, dirty, or corroded.

Battery is discharged.

Four (4) or less nails in tool. Load strip of nails.

Lockout bracket is stuck in lockout position.

Work-contacting element is bent, worn or at
the deepest setting.

Follower is not behind fasteners.

Fuel Cartridge empty.

Spark wire out of spark plug.

Replace battery.

Discontinue use immediately and unplug
from power source. Replace charger and
tag or dispose of charger to prevent
accidental reuse or connection to power
source.

Charge battery.

Clean battery terminals with cloth or pencil
eraser.

Charge battery.

Check lockout. If unable to free return tool to
authorized Paslode dealer for service.

Remove and inspect lower probe. Clean,
adjust or replace lower probe as required.

Position follower behind fasteners.

Replace fuel cartridge.

Remove cap and check spark lead, insert in
spark plug and replace cover.

18

Spark plug is dirty.

No spark is generated.

Clean tool cylinder head and spark plug.

Return tool to authorized Paslode® dealer for
service.

Normal Stage of Operation

If tool will not o perate after following the above service directions, return the tool to an
authorized Paslode.® representative for service.

For the nearest Paslode® representative call 1-800-682-3428.
For factory direct service call 1-800-447-3830.
For Technical support call 1-800-222-6990 or visit our web site at www.paslode.com.
To purchase parts, visit our website at www.itwconstructionparts.com

Troubleshooting

ECIVRESSMELBORPELBISSOPMOTPMYS

Tool operates properly, but fasteners do not
drive fully.

Tool operates, but no fastener is driven.

Tool operates erratically or appears to be
losing power - tool indicator light is green.

Tool operated and drove fasteners, but
driver blade did not return to up position.

Work-contacting element requires adjustment.

Dirty air filter.

There may be loss of seal in combustion
chamber.

Wrong fasteners being used.

Tool requires cleaning.

Follower not properly engaged behind fastener
strip.

Jammed fastener.

Spark plug wire is loose.

Filter element is dirty, causing tool to overheat.

Built-up dirt and debris on driver blade or in
nose bore.

Adjust work contacting element.

Clean filter.

Press work contacting element against
workpiece for 20 seconds. Pull trigger. If
fastener does not drive, there is a leak that
requires service.

Use only fasteners meeting Paslode
specifications. Check Fasteners and
Applications section for fastener types and
sizes recommended for use in Cordless tool.

Clean per instructions.

Position follower behind fastener strip and
engage strip.

Clear jam.

Check spark plug wire.

Remove filter element and clean. Use soap
and water to remove stubborn debris.

Clean driver blade and nose bore with
degreaser cleaner.

®

Return tool to authorized Paslode
dealer for service.

Clean or replace work-contacting element.

Combustion chamber does not drop after
tool cycles.

Mid check is dirty or disabled.

Work-contacting element is bent or is dirty.

®

Cordless

19

20

P

An Illinois Tool Works Company
888 Forest Edge Drive
Vernon Hills, Illinois 60061

www.paslode.com