Partner G20, G25, G30 Installation Instructions Manual
01
290595
Ú Installation instructions
Gas hob
3
Ú Installation instructions
Safety precautions .....................................................................3
Before installing .........................................................................3
Preparing the units..................................................................... 4
Installation of appliance ............................................................4
Setting up the appliance ...................................................................5
Removal of hob...........................................................................5
Set-up, gas and electricity connection..................................... 5
Gas connection ...................................................................................5
Faults in the gas installation/smell of gas .....................................5
Electrical connection ..........................................................................6
Types of connection................................................................... 6
Connection for natural gas (NG) .....................................................6
Liquid gas connection (LPG) ............................................................7
Conversion to a different gas type ...........................................8
Measures to note ................................................................................8
Converting to a different gas type ...................................................8
Parts for the gas conversion.............................................................8
Converting the appliance from natural gas to liquefied gas
(LPG) .....................................................................................................9
Converting the appliance from liquid gas to natural gas............9
Replacing the burner nozzles...........................................................9
Adjusting or replacing the bypass nozzles................................. 10
Removing the hob plate ................................................................. 11
Replacing the bypass nozzles....................................................... 11
Installing the hob.............................................................................. 11
Leak test and function test......................................................12
Check the gas connection ............................................................. 12
Checking the burner nozzles......................................................... 12
Checking the bypass valves.......................................................... 12
Correct flame formation........................................................... 12
Burner ................................................................................................ 12
Technical data – Gas................................................................ 12
Safety precautions
Read the appliance instructions before installing and using.
The graphics in these Assembly instructions are given as a
guide only.
The manufacturer is exempt from all liability if this manual's
requirements are not complied with.
All operations relating to installation, regulation and
conversion to other gas types must be carried out by an
authorised installation engineer, respecting all applicable
regulations, standards and the specifications of the local gas
and electricity providers.
You are recommended to contact the Technical Assistance
Service to convert to another gas type.
Before you begin, turn off the appliance's electricity and gas
supply.
This appliance has been designed for home use only, not for
commercial or professional use. This appliance cannot be
installed on yachts or in caravans. The warranty will only be
valid if the appliance is used for the purpose for which it was
designed.
After connecting the appliance, check that the local conditions
(type of gas and pressure) are compatible with the appliance
settings. The permissible appliance settings can be found on
the label or rating plate.
These instructions are only valid if the appropriate country
symbol appears on the appliance. If the symbol does not
appear on the appliance, it is necessary to refer to the
technical instructions which will provide the necessary
instructions concerning modification of the appliance to the
conditions of use of the country.
This appliance can only be installed in a well-ventilated place in
accordance with existing regulations and ventilation
specifications. The appliance must not be connected to a
combustion product removal device.
The supply cable must be attached to the unit to prevent it from
touching hot parts of the oven or hob.
Appliances with electrical supply must be earthed.
Do not tamper with the appliance's interior. If necessary, call
our Technical Assistance Service.
Before installing
This appliance is class 3 type, according to the EN 30-1-1
regulation for gas appliances: built-in appliance.
The units next to the appliance must be made of non-flammable
materials. The laminated covering and glue for adhering it must
be heat resistant.
This appliance cannot be installed above fridges, washing
machines, dishwashers or similar.
If the hob is installed above an oven, it must have forced
ventilation. Check the dimensions of the oven in your
installation instructions.
If an extractor hood is fitted, this must be done according to the
installation instructions and always allowing for a vertical
minimum clearance of 650 mm to the hob.
4
Preparing the units
Make an appropriate size cut in the work surface.
The appliance must be set up and inserted in accordance with
the specified dimensions. The appliance must not be set up on
any other object.
If the hob is electric or mixed (gas and electricity) and there is
no oven below, place a non-flammable separator (e.g. metal or
plywood) 10 mm from the bottom of the hob. This will prevent
access to the base of the hob.If the hob is gas, it is
recommendable to place the separator at the same distance.
On wood work surfaces, varnish the cutting surfaces with a
special glue. This protects them from moisture which could
collect under the work surface.
Installation of appliance
Note: Wear protective gloves to fit the hob.
Remove the pan support, handles, burner cap and burner
heads.
Turn the appliance over carefully and place it on a soft cloth.
Make sure that the ignition parts are not damaged.
The adhesive seal provided prevents leaks. Adhere it to the
work surface around the cut-out. It must be adhered around the
edge of the area cut out.
Fitting the appliance onto the kitchen unit:
1. Remove the clips from the accessory bag and screw them
into the position indicated so that they can turn freely.
2. Insert and centre the hob.
Press the sides of the hob until it is supported around its
entire perimeter.
3. Turn the clips and tighten them fully.
The position of the clips depends on how thick the work
surface is.
Do not stick the hob onto the worktop with silicone.
PLQ
PLQ
PLQ
PD[
¸
PLQ
5
Setting up the appliance
■ The distance between the top edge of the cooker and the
bottom edge of the extractor hood must comply with the
extractor hood manufacturer's specifications.
■ Ensure that the appliance is not moved again after it is set
up. In particular, the distance from the high-output burner to
the fronts of adjacent units or from the wall must be at least
50 mm.
■ The underside of the appliance heats up during operation.
We therefore recommend that you install a guard plate on the
underside of the appliance.
Removal of hob
Turn off the appliance's electricity and gas supply. Unscrew the clips and proceed in the reverse order to
installation.
Set-up, gas and electricity connection
Gas connection
Installation must only be performed by an approved expert or a
licensed after-sales service engineer in accordance with the
instructions specified in the "Installation instructions".
For the licensed expert or after-sales service
Caution!
The setting values for this appliance are specified on the rating
plate on the back of the appliance. The gas type set in the
factory is marked with an asterisk (*).
If the star symbol appears next to the label "NG", the appliance
is set up for natural gas, and if it appears next to "LPG", the
appliance is set up for liquefied gas.
Caution!
Before connecting the appliance, check whether the local
connection conditions (gas type and pressure) correspond to
the appliance settings. If a change to the appliance settings is
necessary, make the change with the aid of the instructions in
the "Installation instructions".
Caution!
This appliance is not connected to a waste gas main. It must be
connected and commissioned in accordance with the
installation conditions. Do not connect the appliance to a waste
gas main. All ventilation regulations must be observed.
Caution!
The gas connection must be made via a fixed, i.e. not mobile
connection (gas line) or via a safety hose.
Caution!
If using the safety hose, ensure that the hose is not trapped or
crushed. The hose must not come into contact with hot
surfaces.
Caution!
The gas connection must have an easily accessible locking
device.
Safety information
The nominal operating pressure of the appliance is:
for natural gas (G20) 20 mBar, for natural gas (G25) 25 mBar,
for LPG (G30) 30 mBar, for LPG (G31) 37 mBar. The appliance
must be operated at these pressure values. All data on the
rating plate of your appliance relates to these pressure values.
The manufacturer is not responsible for results, performance or
any risk caused by operating the appliance at different values.
: If the gas pressure in your gas supply grid!
for natural gas (G20) is higher than 25 mBar, for natural gas
(G25) is higher than 30 mBar, for LPG (G30) is higher than 36
mBar, for LPG (G31) is higher than 45 mBar, you must use
your appliance in conjunction with a suitable gas regulator, for
safety reasons. Connection, maintenance and configuration of
the gas regulator must be performed by an authorised
installation expert. If you do not know the gas pressure in your
gas supply grid, please ask your local supply grid operator.
Faults in the gas installation/smell of gas
If you notice a smell of gas or faults in the gas installation, you
must:
: WHAT TO DO IF YOU SMELL GAS!
Escaping gas may cause an explosion.
If you smell gas or notice any faults in the gas installation:
■ Immediately shut off the gas supply or close the gas cylinder
valve.
■ Immediately extinguish all naked flames and cigarettes.
■ Do not use any light or appliance switches and do not pull
any plugs out of sockets. Do not use any telephones or
mobile phones within the building.
■ Open windows and ventilate the room.
■ Call the aftersales service or the gas supplier.
PLQ
PD[
Loading...